Door Lock

Inspection

~6min read

INSPECTION

PROCEDURE

1. INSPECT REAR LH DOOR LOCK ASSEMBLY WITH MOTOR

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Battery connection

Result

Battery positive (+) → Terminal 4 (L)

Battery negative (-) → Terminal 1 (UL)

Lock

Battery positive (+) → Terminal 1 (UL)

Battery negative (-) → Terminal 4 (L)

Unlock

If the result is not as specified, replace the rear LH door lock assembly with motor.

*a

Component without wire harness connected

(Rear LH Door Lock Assembly with Motor)

*b

Unlock

*c

Lock

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

6 (LSSR) - 9 (E)

Lock

10 kΩ minimum

6 (LSSR) - 9 (E)

Unlock

Below 1 Ω

If the result is not as specified, replace the rear LH door lock assembly with motor.

2. INSPECT REAR RH DOOR LOCK ASSEMBLY WITH MOTOR (without Double Lock System)

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Battery connection

Result

Battery positive (+) → Terminal 4 (L)

Battery negative (-) → Terminal 1 (UL)

Lock

Battery positive (+) → Terminal 1 (UL)

Battery negative (-) → Terminal 4 (L)

Unlock

If the result is not as specified, replace the rear RH door lock assembly with motor.

*a

Component without wire harness connected

(Rear RH Door Lock Assembly with Motor)

*b

Unlock

*c

Lock

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

6 (LSSR) - 9 (E)

Lock

10 kΩ minimum

6 (LSSR) - 9 (E)

Unlock

Below 1 Ω

If the result is not as specified, replace the rear RH door lock assembly with motor.

3. INSPECT REAR LH DOOR LOCK ASSEMBLY WITH MOTOR (with double locking system)

(a) Check the operation of the door lock motor and the double locking motor.

(1) Apply battery voltage and check the operation of the rear door lock motor and the double locking motor.

OK:

Battery connection

Result

Battery positive (+) → Terminal 4 (DL)

Battery negative (-) → Terminal 3 (UNDL)

Lock

Battery positive (+) → Terminal 3 (UNDL)

Battery negative (-) → Terminal 4 (DL)

Unlock

Battery positive (+) → Terminal 2 (L)

Battery negative (-) → Terminal 1 (UL)

ON

Battery positive (+) → Terminal 1 (UL)

Battery negative (-) → Terminal 2 (L)

Unlock

HINT:

  • Move the door lock motor to the lock position and activate the double locking system. Make sure the doors cannot be unlocked using the control cable.
  • Move the door lock motor to the lock position and deactivate the double locking system. Make sure the doors can be unlocked using the control cable.

If the result is not as specified, replace the rear LH door lock assembly with motor.

*a

Component without wire harness connected

(Rear LH Door Lock Assembly with Motor)

*b

Unlock

*c

Lock

(b) Check the operation of the unlock detection switch and the double locking position switch.

(1) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

5 (LSSR) - 6 (E)

Lock

10 kΩ minimum

5 (LSSR) - 6 (E)

Unlock

Below 1 Ω

9 (DLSR) - 10 (E)

OFF

10 kΩ minimum

9 (DLSR) - 10 (E)

ON

Below 1 Ω

If the result is not as specified, replace the rear LH door lock assembly with motor.

4. INSPECT REAR RH DOOR LOCK ASSEMBLY WITH MOTOR (with double locking system)

(a) Check the operation of the door lock motor and the double locking motor.

(1) Apply battery voltage and check the operation of the rear door lock motor and the double locking motor.

OK:

Battery connection

Result

Battery positive (+) → Terminal 2 (DL)

Battery negative (-) → Terminal 1 (UNDL)

Lock

Battery positive (+) → Terminal 1 (UNDL)

Battery negative (-) → Terminal 2 (DL)

Unlock

Battery positive (+) → Terminal 4 (L)

Battery negative (-) → Terminal 3 (UL)

ON

Battery positive (+) → Terminal 3 (UL)

Battery negative (-) → Terminal 4 (L)

Unlock

HINT:

  • Move the door lock motor to the lock position and activate the double locking system. Make sure the doors cannot be unlocked using the control cable.
  • Move the door lock motor to the lock position and deactivate the double locking system. Make sure the doors can be unlocked using the control cable.

If the result is not as specified, replace the rear RH door lock assembly with motor.

*a

Component without wire harness connected

(Rear RH Door Lock Assembly with Motor)

*b

Unlock

*c

Lock

(b) Check the operation of the unlock detection switch and the double locking position switch.

(1) Measure the resistance according to the value(s) shown in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

9 (LSSR) - 10 (E)

Lock

10 kΩ minimum

9 (LSSR) - 10 (E)

Unlock

Below 1 Ω

5 (DLSR) - 6 (E)

OFF

10 kΩ minimum

5 (DLSR) - 6 (E)

ON

Below 1 Ω

If the result is not as specified, replace the rear RH door lock assembly with motor.