Door Lock

Removal

~5min read

REMOVAL

PRECAUTION / NOTICE / HINT

The adjustments, calibrations, initializations or registrations required after parts have been removed and installed, or replaced during removal/installation of the front door lock assembly with motor, are listed below.

Procedure Required After Replacing / Removing / Installing Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative function when procedure not performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Front door glass sub-assembly
  • Front door glass run

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL CLIP

Click here

4. REMOVE MULTIPLEX NETWORK MAIN SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Click here

5. REMOVE POWER WINDOW SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Click here

6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

7. REMOVE FRONT DOOR GLASS INNER SEAL

Click here

8. REMOVE FRONT DOOR CENTER BELT WEATHERSTRIP

Click here

9. REMOVE FRONT DOOR ACCESS HOLE COVER

Click here

10. REMOVE FRONT DOOR WINDOW GLASS SUB-ASSEMBLY

Click here

11. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP

Click here

12. REMOVE FRONT DOOR WINDOW REGULATOR SASH

Click here

13. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Click here

14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for driver side)

Click here

15. REMOVE FRONT DOOR LOCK ASSEMBLY WITH MOTOR

(a) Disconnect the connector.

*1

Front door unlock rod

Remove in this direction

(b) Using a TORX T30 socket wrench, remove the 3 screws.

(c) Disconnect the front door lock unlock rod as shown in the illustration.

(d) Remove the front door lock assembly with motor.

(e) When reusing the front door lock assembly with motor (without double locking system):

(1) Remove the door lock wire harness grommet from the front door lock assembly with motor.

(f) When reusing the front door lock assembly with motor (with double locking system):

(1) Remove the door lock wire harness grommet from the front door lock assembly with motor.

16. REMOVE FRONT DOOR LOCK STRIKER SUB-ASSEMBLY (without double locking system)

(a) Using a screwdriver with its tip wrapped in protective tape, release the claws as shown in the illustration.

*a

Protective tape

Remove in this direction

(b) Release the guides to remove the front door lock striker sub-assembly from the front door lock assembly with motor.

17. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) without Double Lock System:

(1) Release the guide to remove the front door lock remote control cable assembly from the front door lock assembly with motor.

(b) with Double Lock System:

(1) Release the guide to remove the front door lock remote control cable assembly from the front door lock assembly with motor.

18. REMOVE FRONT DOOR INSIDE LOCK CABLE ASSEMBLY

(a) without Double Lock System:

(1) Release the guide to remove the front door inside lock cable assembly from the front door lock assembly with motor.

(b) with Double Lock System:

(1) Using a screwdriver with its tip wrapped in protective tape, release the claws as shown in the illustration.

*a

Protective tape

Remove in this direction

(2) Release the guide to remove the front door inside lock cable assembly from the front door lock assembly with motor.