Doors / Back Door

Adjustment

~3min read
1special tools
010203040502619N·mlb·ft
Tightening torque found on this page

ADJUSTMENT

PRECAUTION / NOTICE / HINT

*a

Centering Bolt

*b

Standard Bolt

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.
  • The centering bolts are used to install the door hinges on the vehicle body and the door. The door cannot be adjusted while the centering bolts are installed. Replace the centering bolts with standard bolts before making adjustments.
  • The specified torque for standard bolts is shown in the standard bolt table.

    Click here

PROCEDURE

1. INSPECT FRONT DOOR PANEL SUB-ASSEMBLY

(a) Make sure that the clearance measurements of areas "A" to "Y" are within the standard ranges.

Standard clearance

Area

Measurement

Area

Measurement

A

2.1 to 6.1 mm (0.083 to 0.240 in.)

B

-2.0 to 2.0 mm (-0.079 to 0.079 in.)

C

3.1 to 7.1 mm (0.122 to 0.280 in.)

D

2.9 to 6.9 mm (0.114 to 0.272 in.)

E

3.3 to 6.7 mm (0.130 to 0.264 in.)

F

7.1 to 11.1 mm (0.280 to 0.437 in.)

G

3.3 to 6.7 mm (0.130 to 0.264 in.)

H

5.9 to 9.9 mm (0.232 to 0.390 in.)

I

3.3 to 6.7 mm (0.130 to 0.264 in.)

J

3.7 to 7.7 mm (0.146 to 0.303 in.)

K

3.3 to 6.7 mm (0.130 to 0.264 in.)

L

1.4 to 5.4 mm (0.055 to 0.213 in.)

M

3.3 to 6.7 mm (0.130 to 0.264 in.)

N

1.2 to 5.2 mm (0.047 to 0.205 in.)

O

3.3 to 6.7 mm (0.130 to 0.264 in.)

P

0.8 to 3.8 mm (0.031 to 0.150 in.)

Q

2.4 to 6.4 mm (0.094 to 0.252 in.)

R

-2.0 to 2.0 mm (-0.079 to 0.079 in.)

S

2.9 to 5.3 mm (0.114 to 0.209 in.)

T

-1.2 to 1.2 mm (-0.047 to 0.047 in.)

U

7.5 to 11.5 mm (0.295 to 0.453 in.)

V

-2.0 to 2.0 mm (-0.079 to 0.079 in.)

W

3.5 to 8.5 mm (0.138 to 0.335 in.)

X

2.7 to 5.7 mm (0.106 to 0.224 in.)

Y

-1.5 to 1.5 mm (-0.059 to 0.059 in.)

-

-

2. ADJUST FRONT DOOR PANEL SUB-ASSEMBLY

(a) Using SST, loosen the 4 hinge bolts on the vehicle body and adjust the door position.

SST: 09812-00010

(b) After adjustment, tighten the 4 hinge bolts on the vehicle body.

Torque:

26 N·m {265 kgf·cm, 19 ft·lbf}

(c) Loosen the 4 hinge bolts on the door and adjust the door position.

(d) After adjustment, tighten the 4 hinge bolts on the door.

Torque:

Manufactured by TMMT:

26 N·m {265 kgf·cm, 19 ft·lbf}

Manufactured by TMC:

21 N·m {214 kgf·cm, 15 ft·lbf}

(e) Using a "TORX" T40 socket wrench, slightly loosen the 2 striker mounting screws.

(f) Using a brass bar and a hammer, tap the striker to adjust its position.

(g) Using a "TORX" T40 socket wrench, tighten the 2 striker mounting screws after adjustment.

Torque:

23 N·m {235 kgf·cm, 17 ft·lbf}