3zr-fae Battery / Charging

Reassembly

~4min read
7special tools
010203040502.32N·mlb·ft
Tightening torque found on this page

REASSEMBLY

PROCEDURE

1. INSTALL GENERATOR DRIVE END FRAME BEARING

(a) Using the SST and a press, press in a new generator drive end frame bearing.

SST: 09950-60010

09951-00470

SST: 09950-70010

09951-07100

(b) Align the tabs of the retainer plate with the notches in the generator drive end frame, then install the retainer plate.

*a

Tongue

*b

Cutout

(c) Install the 4 screws.

Torque:

2.3 N·m {23 kgf·cm, 20 in·lbf}

2. INSTALL GENERATOR ROTOR ASSEMBLY

(a) Place the generator drive end frame on the generator pulley with clutch.

*1

Generator Rotor Assembly

*2

Generator Drive End Frame

(b) Install the generator rotor assembly to the generator drive end frame.

3. INSTALL GENERATOR COIL ASSEMBLY

(a) Install a new bearing cover seal.

NOTICE:

When installing, align the protrusions of the bearing cover seal with the grooves in the generator coil assembly.

*a

Protrusion

*b

Groove

(b) Using the SST and a press, gently press in the generator coil assembly to install it.

SST: 09612-70100

09612-07240

(c) Install the 4 bolts.

Torque:

5.9 N·m {60 kgf·cm, 52 in·lbf}

4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

(a) While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) pin into the hole in the generator brush holder assembly.

*a

Pin (1.0 mm)

(b) Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:

1.8 N·m {18 kgf·cm, 16 in·lbf}

*a

Pin (1.0 mm)

(c) Remove the pin from the hole in the generator brush holder assembly.

5. INSTALL GENERATOR TERMINAL INSULATOR

(a) Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Make sure to install the generator terminal insulator in the correct direction.

6. INSTALL GENERATOR REAR END COVER

(a) Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:

4.6 N·m {47 kgf·cm, 41 in·lbf}

7. INSTALL GENERATOR PULLEY WITH CLUTCH

(a) Secure the Generator Drive End Frame in a vise between aluminum plates.

(b) Temporarily install the generator pulley with clutch onto the rotor shaft.

(c) Confirm SST (A) and (B) shown in the illustration.

SST: 09820-63021

(d) Place the end of the rotor shaft in the SST (A).

*a

Rotor Shaft

(e) Install the SST (B) on the clutch pulley of the generator.

*1

Generator Pulley with Clutch

(f) Tighten the clutch pulley of the generator by turning the SST (B), as shown in the illustration.

*a

Hold

*b

Torque wrench lever length

*c

SST lever arm length

Turn

Torque:

Specified torque:

80 N·m {816 kgf·cm, 59 ft·lbf}

NOTICE:

Take all necessary precautions, as the clutch pulley of the generator or the rotor shaft may be damaged if the SST is not held in the correct position during this operation.

HINT:

  • Calculate the torque wrench reading when changing the torque wrench lever length.

    Click here

  • When using the SST (lever arm length of 100 mm (3.94 in)) + torque wrench (lever arm length of 400 mm (15.7 in)): 64 N·m (653 kgf·cm, 47 lbf·ft)

(g) Remove the SST from the clutch pulley of the generator.

(h) Check that the clutch pulley of the generator turns smoothly.

(i) Remove the drive end frame of the generator from the vise.

8. INSTALL GENERATOR PULLEY CAP

(a) Install a new generator pulley cap on the clutch pulley of the generator.