Brakes (Front)

Installation

~4min read
0408012016020010779N·mlb·ft
Tightening torque found on this page

INSTALLATION

PRECAUTION / NOTICE / HINT

NOTICE:

  • Immediately after installing the brake pads, braking performance may be reduced. Always perform a road test in a safe area, paying attention to the surroundings.
  • After replacing the front disc brake pads, always perform a road test to check brake effectiveness and whether there is any vibration.

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. INSTALL FRONT DISC

(a) Align the front disc alignment marks with the front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position with the minimum front disc runout.

*a

Alignment Mark

2. INSTALL FRONT DISC BRAKE CYLINDER SUPPORT

(a) Install the front disc brake cylinder support to the steering knuckle with the 2 bolts.

Torque:

107 N·m {1 091 kgf·cm, 79 ft·lbf}

3. INSTALL FRONT DISC BRAKE BUSHING DUST BOOT

(a) Apply a light coat of lithium soap base glycol grease around the entire circumference of 2 new front disc brake bushing dust boots.

HINT:

Apply a minimum of 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bushing dust boot.

Lithium soap base glycol grease

(b) Install the 2 front disc brake bushing dust boots to the front disc brake cylinder support.

4. INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

(a) Apply a light coat of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).

Lithium soap base glycol grease

(b) Install a new front disc brake cylinder slide bushing to the front disc brake cylinder slide pin (lower side).

(c) Apply a light coat of lithium soap base glycol grease to the sliding and sealing surfaces of the 2 front disc brake cylinder slide pins.

Lithium soap base glycol grease

(d) Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder support.

(e) Push each front disc brake cylinder slide pin into the front disc brake bushing dust boot to engage the pin in the boot.

5. INSTALL FRONT DISC BRAKE PAD SUPPORT PLATE

(a) Install the 4 front disc brake pad support plates to the front disc brake cylinder support.

NOTICE:

  • Be sure to install the front disc brake pad support plate in the correct position and direction.
  • If reusing the brake pad support plates, use the identification marks made during removal to install them in their original positions.

6. INSTALL FRONT DISC BRAKE ANTI-SQUEAL SHIM KIT

Click here

7. INSTALL FRONT DISC BRAKE PAD

(a) Install the 2 front disc brake pads to the front disc brake cylinder support.

8. INSTALL FRONT DISC BRAKE WHEEL CYLINDER ASSEMBLY

(a) Hold each front disc brake cylinder slide pin and install the front disc brake wheel cylinder assembly to the front disc brake cylinder support with the 2 new bolts.

Torque:

32 N·m {321 kgf·cm, 23 ft·lbf}

*a

Turn

*b

Hold

CAUTION:

  • Do not reuse the bolts.
  • If the bolts are reused, the front disc brake wheel cylinder assembly may detach, resulting in an accident.

9. CONNECT FRONT FLEXIBLE HOSE

(a) Connect the front flexible hose to the front disc brake wheel cylinder assembly using a new union bolt and new gaskets.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

NOTICE:

Install the front flexible hose lock correctly in the lock hole of the front disc brake wheel cylinder assembly.

10. BLEED BRAKE LINE

Click here

11. INSTALL FRONT WHEEL

Click here