Axle and Differential

Installation

~5min read
0408012016020013096N·mlb·ft
Tightening torque found on this page

INSTALLATION

PRECAUTION / NOTICE / HINT

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. INSTALL FRONT AXLE HUB SUBASSEMBLY

(a) Clamp the steering knuckle between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.

(b) Install the front axle hub subassembly and front disc brake dust cover to the steering knuckle with the 3 bolts.

Torque:

130 N·m {1 326 kgf·cm, 96 ft·lbf}

NOTICE:

  • Be careful not to damage the speed sensor rotor or contact surfaces.
  • Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.

2. INSTALL FRONT AXLE ASSEMBLY

(a) Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz.) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

Toyota Body Grease W

(b) Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.

Torque:

270 N·m {2 753 kgf·cm, 199 ft·lbf}

NOTICE:

  • Do not apply lubricant to the contact surfaces of the steering knuckle and shock absorber.
  • When installing the nuts, prevent the bolts from turning.

HINT:

The bolts can be installed in either direction. However, make sure both bolts are installed in the same direction.

3. INSTALL FRONT AXLE SHAFT ASSEMBLY

(a) Align the alignment marks on the front axle shaft assembly and front axle hub subassembly, then connect the front axle shaft assembly to the front axle assembly.

NOTICE:

  • Do not push the front axle assembly outward from the vehicle more than necessary.
  • Make sure there is no foreign matter on the speed sensor rotor or contact surfaces.
  • Do not damage the front axle shaft outer joint boot.
  • Do not damage the front disc brake dust cover.
  • Be careful not to damage the speed sensor rotor.

*a

Alignment Mark

4. CONNECT FRONT SUSPENSION LOWER ARM SUB-ASSEMBLY NO. 1

(a) Connect the front suspension lower arm subassembly No. 1 to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:

89 N·m {908 kgf·cm, 66 ft·lbf}

5. CONNECT TIE ROD END SUBASSEMBLY

Click here

6. INSTALL FRONT DISC

Click here

7. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Click here

8. INSTALL FRONT AXLE SHAFT NUT

(a) Clean the threaded portions of the front axle shaft assembly and a new front axle shaft nut using a residue-free solvent.

NOTICE:

  • Make sure to perform this work even when using a new front axle shaft assembly.
  • Keep the threaded portions free from oil or foreign objects.

(b) Using a 30 mm long socket wrench, while applying the brakes, temporarily install a new front axle hub nut.

Torque:

216 N·m {2 203 kgf·cm, 159 ft·lbf}

NOTICE:

Stake the front axle shaft nut after checking its tightening and out-of-round, using the following steps.

HINT:

Keep the brake pedal depressed to prevent the front axle shaft from rotating.

9. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY

Click here

10. REMOVE FRONT DISC

Click here

11. INSPECT FRONT AXLE HUB BEARING TIGHTENING

Click here

12. INSPECT FRONT AXLE HUB OUT-OF-ROUND

Click here

13. INSTALL FRONT DISC

Click here

14. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

Click here

15. INSTALL FRONT SPEED SENSOR

(a) Engage the 2 front speed sensor hooks with the front shock absorber assembly.

NOTICE:

Do not twist the front speed sensor when installing it.

(b) Install the front speed sensor and front hose on the front shock absorber assembly using the bolt.

Torque:

29 N·m {296 kgf·cm, 21 ft·lbf}

NOTICE:

Do not twist the front hose when installing it.

(c) Install the front speed sensor to the steering knuckle with the bolt.

Torque:

8.5 N·m {87 kgf·cm, 75 in·lbf}

NOTICE:

  • Prevent foreign matter from adhering to the front speed sensor tip.
  • Fully insert the front speed sensor body into the steering knuckle before tightening the bolt.
  • After installing the front speed sensor to the steering knuckle, make sure there is no gap between the front speed sensor bracket and the steering knuckle. Also make sure that no parts are caught by foreign matter.
  • Do not twist the front speed sensor when installing it.

(d) Engage the clip.

NOTICE:

Do not twist the front speed sensor when installing it.

16. STAKE FRONT AXLE SHAFT NUT

(a) Using a chisel and hammer, stake the front axle shaft nut.

17. INSTALL FRONT WHEEL

Click here

18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Click here

19. CHECK SPEED SENSOR SIGNAL

Click here