Installation
INSTALLATION
COMPONENTS (INSTALLATION)
Procedure | Part Name Code | ![]() | ![]() | ![]() |
|
|---|---|---|---|---|---|
1 |
REAR FLEXIBLE HOSE |
47319F |
- |
- |
|
2 |
ADD BRAKE FLUID |
- |
- |
- |
|
3 |
BLEED BRAKE LINE |
- |
- |
- |
|
4 |
REAR WHEEL |
- |
- |
- |
- |
5 |
INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL |
- |
- |
- |
|
*A |
for HEV Model |
- |
- |
![]() |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
* |
For use with a union nut wrench |
● |
Non-reusable part |
- |
- |
NOTICE:
- Because the left and right rear flexible hoses are not interchangeable, verify the part number when installing the rear flexible hoses.
- When reusing the rear flexible hoses, use the identification marks created during removal to install each rear flexible hose to its original position.
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL REAR FLEXIBLE HOSE
![]() |
NOTICE: When installing the rear flexible hose, minimize twisting of the hose. |
*a |
Torque Wrench Fulcrum Length |
*b |
Identification Mark |
(1) Install the rear flexible hose with a new clip.
NOTICE:
- Install the clip as far as it will go.
- When installing the rear flexible hose LH, face the identification mark to the upper side of the vehicle.
(2) Using a union nut wrench, connect the brake line to the rear flexible hose while holding the rear flexible hose with a wrench.
Torque:
Specified tightening torque :
15,2 N·m {155 kgf·cm, 11 ft·lbf}
NOTICE:
- Do not kink or damage the brake line.
- Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.
HINT:
- Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
.gif)
- When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
13.4 N*m (137 kgf*cm, 10 ft.*lbf)
(3) Install the rear flexible hose LH to the rear flexible hose bracket with the bolt.
Torque:
29 N·m {296 kgf·cm, 21 ft·lbf}
(4) Install the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.
Torque:
30 N·m {310 kgf·cm, 22 ft·lbf}
NOTICE:
Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.
2. ADD BRAKE FLUID
- for HEV model:
Click here
.gif)
- for Gasoline model:
Click here
.gif)
3. BLEED BRAKE LINE
- for HEV model: Click here
.gif)
- for Gasoline model: Click here
.gif)
4. INSTALL REAR WHEEL
Click here ![]()
5. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL (for HEV Model)
HINT:
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click here ![]()
.png)
.png)
.png)
.png)