Vehicle Exterior

Power Back Door Warning System does not Operate

~3min read

DESCRIPTION

When the power back door warning system does not operate, one of the following may be malfunctioning: 1) wireless door lock control system, 2) power back door warning buzzer circuit, 3) multiplex network door ECU.

WIRING DIAGRAM

NOTICE:

  • If the replacement, removal and installation of the multiplex network door ECU or disconnection of the connectors of the multiplex network door ECU has been performed, initialize the power back door system.

    Click here

  • The power back door warning function can be customized. Make sure the function is ON.

    Click here

  • If the main body ECU (multiplex network body ECU) is replaced, refer to Registration.

    for HEV Model: Click here

    for Gasoline Model: Click here

PROCEDURE

  1. CHECK OPERATION

(a) Check power back door system operation.

Click here

Result

Proceed to

Hazard warning light does not come on

A

Power back door warning buzzer does not operate

B

B

GO TO STEP 6

A
  1. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM (HAZARD ANSWER-BACK FUNCTION)

(a) Check wireless door lock operation.

Click here

OK:

Hazard answer-back function operates normally.

NG

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM

OK
  1. REPLACE MULTIPLEX NETWORK DOOR ECU

(a) Temporarily replace the multiplex network door ECU with a new or normally functioning one.

Click here

NEXT
  1. INITIALIZE MULTIPLEX NETWORK DOOR ECU

(a) Perform the initialization for the multiplex network door ECU.

Click here

NEXT
  1. CHECK POWER BACK DOOR SYSTEM

(a) Check that the power back door hazard warning lights operate normally.

Click here

OK:

The power back door hazard warning lights operate normally.

OK

END (MULTIPLEX NETWORK DOOR ECU WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

  1. PERFORM ACTIVE TEST USING GTS

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Back Door > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PBD Buzzer (Small Volume)

Power back door warning buzzer sound (small volume)

Start

-

PBD Buzzer (Middle Volume)

Power back door warning buzzer sound (Middle volume)

Start

-

PBD Buzzer (Large Volume)

Power back door warning buzzer sound (Large volume)

Start

-

Body Electrical > Back Door > Active Test

PBD Buzzer (Small Volume)

Body Electrical > Back Door > Active Test

PBD Buzzer (Middle Volume)

Body Electrical > Back Door > Active Test

PBD Buzzer (Large Volume)

OK:

Power back door warning buzzer sounds.

OK

REPLACE MULTIPLEX NETWORK DOOR ECU

NG
  1. CHECK HARNESS AND CONNECTOR (POWER BACK DOOR WARNING BUZZER - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND)

(a) Disconnect the U23 power back door warning buzzer connector.

(b) Disconnect the U39 multiplex network door ECU connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

U23-1 (BZR+) - U39-1 (BZR+)

Always

Below 1 Ω

U23-2 (BZR-) - Body ground

Always

Below 1 Ω

U23-1 (BZR+) or U39-1 (BZR+) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE POWER BACK DOOR WARNING BUZZER

(a) Temporarily replace the power back door warning buzzer with a new or normally functioning one.

Click here

NEXT
  1. CHECK POWER BACK DOOR SYSTEM

(a) Check that the power back door warning buzzer operates normally.

Click here

OK:

Power back door warning buzzer sounds.

OK

END (POWER BACK DOOR WARNING BUZZER WAS DEFECTIVE)

NG

REPLACE MULTIPLEX NETWORK DOOR ECU