Registration
REGISTRATION
PROCEDURE
1. REPAIR INSTRUCTION
CAUTION:
As weak radio waves are emitted from the electrical key transmitter sub-assembly, if a pacemaker is being used, be sure to read the pacemaker instruction manual and the following.
- People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should keep away from the smart key system antennas. The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your dealer for details, such as the frequency of radio waves and timing of the emitted radio waves. Then, consult your doctor to see if you should disable the entry function.
Click here
.gif)
- User of any electrical medical device other than implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverter defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
- Ask your dealer for details for disabling the entry function.
Click here
.gif)
NOTICE:
PRECAUTION WHEN REPLACING PARTS
- Code registration is necessary when any of the following parts is replaced with a new one. After replacing a part, any part that has performed registration cannot be returned.
- Certification ECU (smart key ECU assembly)
- ID code box (immobiliser code ECU)
- Electrical key transmitter sub-assembly
- Main body ECU (multiplex network body ECU)
- DCM (telematics transceiver)*
- *: for Remote Connect Compatible Type
PRECAUTION FOR REGISTRATION
- Make sure that only 1 electrical key transmitter sub-assembly is in the cabin during registration procedures. If 2 or more electrical key transmitter sub-assemblies are in the cabin simultaneously, the electric waves will interfere with each other, preventing normal registration.
- A maximum of 4 electrical key transmitter sub-assemblies can be registered (this includes any electrical key transmitter sub-assemblies registered when the vehicle was purchased).
- If the battery is depleted during the electrical key transmitter sub-assembly registration procedure, there may be cases in which the electrical key transmitter sub-assembly cannot be registered again. Therefore, make sure to perform work with a sufficiently charged battery.
- If any of the work times are exceeded, finish the procedure.
- Do not disconnect the battery during the Registration.
- Do not perform operations that create an electrical load such as operating the power windows.
- If Smart Key System is canceled, registration cannot be performed.
Click here
.gif)
2. EXPLANATION OF IMMOBILISER KEY ID REGISTRATION PROCEDURE
(a) Addressing customer requests (perform work in chart below in order starting from left)
Customer Request/Condition | Undesignated key permanent erasure | All keys ID erasure (Smart code reset) | New key ID registration | Additional key ID registration |
|---|---|---|---|---|
Refer to PROCEDURE |
"5" |
"6" |
"3" |
"4" |
All electrical key transmitter sub-assemblies are lost |
- |
![]() |
![]() |
- |
Registering additional electrical key transmitter sub-assembly |
- |
- |
- |
![]() |
Making a lost electrical key transmitter sub-assembly unusable |
![]() |
- |
- |
- |
(b) Addressing malfunctions 1 (perform work in chart below in order starting from left)
Certification ECU (smart key ECU assembly) malfunctionCondition (The number of the electrical key transmitter sub-assemblies customer has brought) | Undesignated key permanent erasure | Replace certification ECU (smart key ECU assembly) | Replace ID code box (immobiliser code ECU) | New key ID registration | ECU code registration | ECU communication ID registration | Remote engine start and stop registration* |
|---|---|---|---|---|---|---|---|
Refer to PROCEDURE |
"5" |
"3" |
"7" |
"8" |
"10" |
||
All electrical key transmitter sub-assemblies |
- |
![]() |
- |
![]() |
- |
- |
![]() |
At least 1 electrical key transmitter sub-assembly (Key ID codes can be registered and cleared) |
![]() |
![]() |
- |
![]() |
- |
- |
![]() |
At least 1 electrical key transmitter sub-assembly (Key ID codes cannot be either registered or cleared) |
- |
![]() |
![]() |
![]() |
- |
![]() |
![]() |
All electrical key transmitter sub-assemblies are lost |
- |
![]() |
![]() |
![]() |
- |
![]() |
![]() |
- *: for Remote Connect Compatible Type
(c) Addressing malfunctions 2 (perform work in chart below in order starting from left)
ID code box (immobiliser code ECU) malfunctionCondition (The number of the electrical key transmitter sub-assemblies customer has brought) | Undesignated key permanent erasure | Replace certification ECU (smart key ECU assembly) | Replace ID code box (immobiliser code ECU) | New key ID registration | ECU code registration | ECU communication ID registration | Remote engine start and stop registration* |
|---|---|---|---|---|---|---|---|
Refer to PROCEDURE |
"5" |
"3" |
"7" |
"8" |
"10" |
||
At least 1 electrical key transmitter sub-assembly |
- |
- |
![]() |
- |
![]() |
![]() |
- |
All electrical key transmitter sub-assemblies are lost |
- |
![]() |
![]() |
![]() |
- |
![]() |
![]() |
- *: for Remote Connect Compatible Type
(d) Addressing malfunctions 3 (perform work in chart below in order starting from left)
Electrical key transmitter sub-assemblies malfunctionCondition (The number of the electrical key transmitter sub-assemblies customer has brought) | Undesignated key permanent erasure | All keys ID erasure (Smart code reset) | New key ID registration | Additional key ID registration |
|---|---|---|---|---|
Refer to PROCEDURE |
"5" |
"6" |
"3" |
"4" |
One or more electrical key transmitter sub-assembly that operates normally |
![]() |
- |
- |
![]() |
All electrical key transmitter sub-assembly lost or any electrical key transmitter sub-assembly does not operate normally |
- |
![]() |
![]() |
- |
(e) Addressing malfunctions 4 (perform work in chart below in order starting from left)
Malfunctioning ECU | Condition | Replace hybrid vehicle control ECU | Replace main body ECU (multiplex network body ECU) | Replace DCM (telematics transceiver)* | ECU code registration | ECU communication ID registration | Remote door lock and unlock registration* | Remote engine start and stop registration* |
|---|---|---|---|---|---|---|---|---|
Refer to PROCEDURE |
"7" |
"8" |
"9" |
"10" |
||||
Hybrid vehicle control ECU |
When replacing a new one |
![]() |
- |
- |
- |
- |
- |
- |
When replacing a used one |
![]() |
- |
- |
- |
![]() |
- |
- |
|
Main body ECU (multiplex network body ECU) |
When replacing a new one |
- |
![]() |
- |
![]() |
- |
![]() |
- |
DCM (telematics transceiver)* |
When replacing a new one |
- |
- |
![]() |
- |
- |
![]() |
![]() |
- *: for Remote Connect Compatible Type
3. NEW KEY ID REGISTRATION
NOTICE:
- When the certification ECU (smart key ECU assembly) is replaced, register all electrical key transmitter sub-assemblies used by the customer.
- Registered electrical key transmitter sub-assemblies other than those registered during the certification ECU (smart key ECU assembly) replacement cannot be re-registered, and therefore they can no longer be used.
- Immediately after replacing the certification ECU (smart key ECU assembly), the GTS item "Number of Registered Codes" should change to "0". If this item does not change to "0", the certification ECU (smart key ECU assembly) may be registered to another vehicle. A certification ECU (smart key ECU assembly) which is registered to another vehicle cannot be used.
Process | Procedure | Time limit (seconds) |
|---|---|---|
1. Start of registration |
|
- |
2. Get Pass-Code |
|
- |
3. Confirmation of all registered electrical key transmitter sub-assemblies (When only the certification ECU (smart key ECU assembly) is replaced) |
HINT: When performing the electrical key transmitter sub-assembly confirmation procedure the security indicator light comes on and remains on until all the electrical key transmitter sub-assemblies are confirmed. |
30 |
4. Verification of unregistered electrical key transmitter sub-assembly |
|
30 |
5. End of registration |
Finish new key ID code registration. |
- |
4. ADDITIONAL KEY ID REGISTRATION
NOTICE:
If an electrical key transmitter sub-assembly has recently been registered, the new key registration warning message will be displayed on the multi-information display and cannot be cleared for 10 days.*
This message is displayed to inform the user that an electrical key transmitter sub-assembly has been registered and help prevent the vehicle from being stolen if the registration was unauthorized.
- *: Display of the warning message will be suspended when any of the following conditions is met:
- The warning message has been displayed for 60 seconds.
- All of the doors are closed and locked.
- Ignition switch is turned to ON.
Process | Procedure | Time limit (seconds) |
|---|---|---|
1. Start of registration |
|
- |
2. Get Pass-Code |
|
- |
3. Confirmation of registered electrical key transmitter sub-assemblies |
HINT: When checking registered electrical key transmitter sub-assemblies, check using an electrical key transmitter sub-assembly that is registered to the vehicle. |
30 |
4. Verification of unregistered electrical key transmitter sub-assembly |
|
30 |
5. End of registration |
Finish additional key ID code registration. |
- |
5. UNDESIGNATED KEY PERMANENT ERASURE
NOTICE:
If Undesignated Key Permanent Erasure is performed, previously registered electrical key transmitter sub-assemblies cannot be re-registered, and therefore they can no longer be used.
HINT:
Undesignated Key Permanent Erasure can be used to delete and disable all key IDs other than the electrical key transmitter sub-assemblies selected during "confirmation of registered electrical key transmitter sub-assemblies to keep (process No. 3)".
Process | Procedure | Time limit (seconds) |
|---|---|---|
1. Start of erasure |
|
- |
2. Get Pass-Code |
|
- |
3. Confirmation of registered electrical key transmitter sub-assemblies to keep |
HINT: The security indicator light illuminates when all the registered electrical key transmitter sub-assemblies to keep are confirmed. |
30 |
4. Erasure of key ID |
|
- |
5. Confirmation of ECU code |
HINT: The security indicator light goes off when confirmation of ECU code is completed. |
- |
6. Erasure of ID code |
|
- |
7. End of erasure |
Finish key ID erasure. |
- |
6. ALL KEYS ID ERASURE (SMART CODE RESET)
NOTICE:
Do not perform "Smart Code Reset" (all key ID erasure) until all of the malfunctions and symptoms have been confirmed and resolved. If all key ID erasure is performed without confirming or resolving malfunctions, key registration will be unable to be performed, resulting in unnecessary part replacement.
Process | Procedure | Time limit (seconds) |
|---|---|---|
1. Start of erasure |
|
- |
2. Get Pass-Code |
NOTICE: After obtaining the Pass-Code, do not turn off the GTS until erasure is completed. If the GTS is turned off before erasure is completed, obtain the Pass-Code once more. |
- |
3. Erasure of ID code |
|
- |
4. End of erasure |
Finish key ID code erasure. |
- |
7. ECU CODE REGISTRATION
Process | Procedure | Time limit (seconds) |
|---|---|---|
1. Start of registration |
|
- |
2. Confirmation of registered electrical key transmitter sub-assemblies |
HINT: When checking registered electrical key transmitter sub-assemblies, check using an electrical key transmitter sub-assembly that is registered to the vehicle. |
30 |
3. Registration of ECU code |
|
- |
4. End of registration |
Finish ECU code registration. |
- |
8. ECU COMMUNICATION ID REGISTRATION
NOTICE:
Do not open or close the driver door during registration. If the driver door is opened or closed, restart from step 1 of "Start of registration".
Process | Procedure |
|---|---|
1. Start of registration |
|
2. ECU communication ID registration |
|
3. Confirmation of registration |
|
4. Clear DTC |
|
5. End of registration |
Finish ECU communication ID registration. |
9. REMOTE DOOR LOCK AND UNLOCK REGISTRATION
HINT:
After completing the registered work to vehicle, it is required to turn the vehicle connection setting to ON with the Smartphone Application.
Process | Procedure |
|---|---|
1. Start of registration |
|
2. Registration of remote door lock and unlock |
|
3. End of registration |
Finish remote door lock and unlock registration. |
10. REMOTE ENGINE START AND STOP REGISTRATION
HINT:
After completing the registered work to vehicle, it is required to turn the vehicle connection setting to ON with the Smartphone Application.
Process | Procedure |
|---|---|
1. Start of registration |
|
2. Registration of remote engine start and stop |
|
3. End of registration |
Finish remote engine start and stop registration. |
.png)