Toyota RAV4 Quiz
2Az-fe fuel

Fuel tank

In this manual: 2Az-fe fuel
Introduction — 37Interior — 12Exterior — 432Az-fe engine mechanical — 1552Az-fe ignition — 182Az-fe charging — 232Az-fe emission control — 82az-fe exhaust — 32Az-fe fuel — 72Az-fe lubrication — 4Brake — 17Brake control — 63U140f automatic transaxle — 59Instrument panel — 8Suspension — 18Drive shaft — 23Axle — 6Tire and wheel — 30Air conditioning — 93Lighting — 45Cruise control — 21Differential — 12Door lock — 31Engine immobiliser — 21Horn — 5Can communication — 27Mirror — 5Parking brake — 5Power steering — 27Propeller shaft — 3Seat — 29Seat belt — 27Sliding roof — 25Steering column — 6Wiper and washer — 11Supplemental restraint system — 95Other system — 5Maintenance — 14
57steps
~342min
4/5difficulty
Done 0 of 57
Components
Toyota RAV4. Fuel tank

Toyota RAV4. Fuel tank

Removal
  1. Discharge fuel system pressure (see page fu-9)
  2. Disconnect cable from negative battery terminal
Caution: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
  1. Remove fuel tank cap
  2. Remove front floor cover
  3. Remove the nut, bolt, 3 clips and floor cover.
  4. Remove no. 1 Floor under cover
  5. Remove the 2 nuts, clip and floor under cover.
    Toyota RAV4. Remove no. 1 Floor under cover

  1. Disconnect no. 2 Parking brake cable assembly
Toyota RAV4. Disconnect no. 2 Parking brake cable assembly

  1. Remove the 2 bolts and disconnect the parking brake cable.
  2. Disconnect fuel tank main tube subassembly
    Toyota RAV4. Disconnect fuel tank main tube subassembly

  1. Pinch and pull the main tube connector to disconnect the connector from the pipe.
Notice:
  • Check for foreign matter in the pipe and around the connector. Clean if necessary.
Foreign matter may damage the o-ring or cause leaks in the seal between the pipe and connector.
  • Do not use any tools to separate the pipe and connector.
  • Do not forcefully bend or twist the nylon tube.
  • Check for foreign matter on the pipe seal surface. Clean if necessary.
  • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
  • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
    1. Disconnect the evap hose from the tank.
    2. Disconnect fuel tank to filler pipe hose
      Toyota RAV4. Disconnect fuel tank to filler pipe hose

    1. Disconnect the filler pipe hose from the fuel tank.
    2. Disconnect fuel tank breather hose
      Toyota RAV4. Disconnect fuel tank breather hose

    1. Disconnect the breather hose from the fuel tank.
    Notice:
    • Check for foreign matter in the pipe and around the connector. Clean if necessary.
    Foreign matter may damage the o-ring or cause leaks in the seal between the pipe and connector.
  • Do not use any tools to separate the pipe and connector.
  • Do not forcefully bend or twist the nylon tube.
  • Check for foreign matter on the pipe seal surface. Clean if necessary.
  • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
  • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.
    1. Remove fuel tank filler pipe
    2. Remove the 3 bolts and filler pipe protector.
    3. Remove the 2 bolts and filler pipe.
    4. Remove fuel tank assembly
      Toyota RAV4. Remove fuel tank assembly

    1. Set a mission jack underneath the fuel tank.
    2. Remove the 6 bolts and 3 fuel tank bands.
    3. Slightly lower the mission jack.
    Notice:

    Be careful not to cut the wirings.

    Toyota RAV4. Remove fuel tank assembly

    1. Fold back approximately half of each cushion rubber so that the wire harness can be detached from the fuel tank in the step below.
    2. Disconnect the fuel pump connector and sender gauge connector.
    Notice:
    • Before this procedure, check the connector for dirt, mud or other contamination.
    • Do not use any tools in this procedure.
    1. Detach the wire harness from the 4 clamps and remove the fuel tank.
    Disassembly
    1. Remove fuel tank main tube sub-assembly (see page fu-30)
    2. Remove fuel tank vent tube set plate (see page fu-30)
    3. Remove fuel suction with pump assembly (see page fu-30)
    4. Remove fuel tank main tube sub-assembly
    5. Remove the tube from the fuel tube clamps.
    6. Remove no. 1 Fuel tube clamp
      Toyota RAV4. Remove no. 1 Fuel tube clamp

    1. Remove the 4 tube clamps from the fuel tank.
    2. Remove no. 1 Fuel tank cushion
      Toyota RAV4. Remove no. 1 Fuel tank cushion

    1. Remove the 7 fuel tank cushions from the fuel tank.
    2. Remove fuel sender gauge assembly
      Toyota RAV4. Remove fuel sender gauge assembly

    1. Remove the 5 screws and sender gauge.
    Reassembly
    1. Install fuel sender gauge assembly
    Toyota RAV4. Install fuel sender gauge assembly

    1. Install the sender gauge with the 5 bolts.
    Torque: 1.5 N*m (15 kgf*cm, 13 in.*Lbf)
    1. Install no. 1 Fuel tank cushion
    Toyota RAV4. Install no. 1 Fuel tank cushion

    1. Install 7 new fuel tank cushions onto the fuel tank as shown in the illustration.
    2. Install no. 1 Fuel tube clamp
      Toyota RAV4. Install no. 1 Fuel tube clamp

    1. Install the 4 tube clamps to the fuel tank.
    2. Install fuel tank main tube sub-assembly
    3. Install the tube with the 4 clips.
    4. Install fuel suction with pump assembly (see page fu-36)
    5. Install fuel tank vent tube set plate (see page fu-36)
    6. Install fuel tank main tube sub-assembly (see page fu-37)
    Installation
    1. Install fuel tank assembly
    Toyota RAV4. Install fuel tank assembly

    1. Set the fuel tank on a mission jack.
    2. Lift up the mission jack.
    3. Fold back the 2 cushion rubbers.
    4. Connect the fuel pump connector and sender gauge connector to the fuel tank.
    Notice:

    Be careful not to cut the wirings.

    1. Attach the wire harness to the 4 clamps.
    2. Install the 3 fuel tank bands with the 6 bolts.
    Torque: 40 n*m (408 kgf*cm, 30 ft.*Lbf)
    1. Install fuel tank filler pipe
    Toyota RAV4. Install fuel tank filler pipe

    1. Install the filler pipe with the 2 bolts.
    Torque: 23.5 N*m (240 kgf*cm, 17 ft.*Lbf)
  • Install the filler pipe protector with the 3 bolts.
    1. Connect fuel tank to filler pipe hose
    Toyota RAV4. Connect fuel tank to filler pipe hose

    1. Connect the filler pipe hose to the fuel tank.
    2. Connect fuel tank breather hose
      Toyota RAV4. Connect fuel tank breather hose

    1. Connect the fuel tank breather hose to the fuel tank.
    Notice:
    • Before installing the tube connector to the pipe, check the connector for damage and foreign matter.
    • Check that the connector and pipe is securely connected by trying to pull them apart.
    1. Connect fuel tank main tube sub-assembly
    Notice:

    Before installing the tube connector to the pipe, check the connector for damage and foreign matter.

    1. Connect the main tube connector to the pipe. Push the 2 parts together firmly until a "click" sound is heard.
    Notice:

    Check that the connector and pipe are securely connected by trying to pull them apart.

    1. Connect the evap hose to the fuel tank.
    Toyota RAV4. Connect fuel tank main tube sub-assembly

    1. Install no. 1 Floor under cover
    2. Install the floor cover with the clip and 2 nuts.
      Toyota RAV4. Install no. 1 Floor under cover

    1. Install front floor cover
    2. Install the floor under cover with the 3 clips, bolt and nut.
    3. Install no. 2 Parking brake cable assembly
      Toyota RAV4. Install no. 2 Parking brake cable assembly

    1. Install the parking brake cable with the 2 bolts.
    2. Install fuel tank cap
    3. Connect cable to negative battery terminal
    4. Check for fuel leaks (see page fu-14)

    Test yourself

    A quick Toyota RAV4 quiz: every answer comes with an explanation and a link to the manual page.