Toyota Sienna Quiz
Cruise control

Cruise Control Switch Circuit

In this manual: Cruise control
Introduction — 55Service specifications — 7Maintenance — 7Engine — 264U151e automatic transaxle — 108Transfer — 19Propeller shaft — 8Drive shaft — 14Differential — 16Axle — 18Suspension — 37Tire and wheel — 54Brake control — 141Parking brake — 16Steering Column — 11Power steering — 18Air conditioning — 106Supplemental restraint system — 146Seat belt — 22Theft deterrent — 14Engine immobiliser — 17Cruise control — 65Lighting — 61Wiper and washer — 13Door lock — 42Meter — 28Audio / visual — 94Navigation — 108Park assist / monitoring — 33Horn — 5Garage door opener — 42GR-FE Engine control system — 126Supplemental restraint system — 147Other system — 14Windshield / windowglass — 43Mirror — 23Instrument panel — 6Seat belt — 22Seat — 92Engine hood / door — 104Exterior — 39Interior — 5Sliding roof — 9Multiplex communication — 18Can communication — 23
11steps
~66min
3/5difficulty
Done 0 of 11

DESCRIPTION

The cruise control main switch operates 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP, and CANCEL. The SET, TAP-DOWN, and - (COAST) functions, and the RES (RESUME), TAP-UP, and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

WIRING DIAGRAM

INSPECTION PROCEDURE

1 READ VALUE OF INTELLIGENT TESTER

READ VALUE OF INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.
  3. Check the DATA LIST for proper functioning of the cruise control main switch.

ECM (Cruise control):

ECM (Cruise control)

OK: When the cruise control main switch is operated, the display changes as shown above.

Result

Result

2 INSPECT CRUISE CONTROL MAIN SWITCH

  1. Remove the cruise control main switch.
  2. Measure the resistance according to the value(s) in the table below.
    INSPECT CRUISE CONTROL MAIN SWITCH

Standard resistance

Standard resistance

3 CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)

CHECK HARNESS AND CONNECTOR (CRUISE CONTROL MAIN SWITCH - SPIRAL CABLE)
  1. Disconnect the b1 connector from the spiral cable.
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

4 CHECK SPIRAL CABLE

CHECK SPIRAL CABLE

NOTICE: The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

HINT:

  • Removal (34)
  • Installation (34)
  1. Remove the spiral cable.
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

HINT: The spiral cable makes a maximum of approximately 5 rotations.

CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

  1. Disconnect the E5 connector from the ECM.
    CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
  2. Measure the resistance according to the value(s) in the table below.

Standard resistance

Standard resistance

REPLACE ECM

Test yourself

A quick Toyota Sienna quiz: every answer comes with an explanation and a link to the manual page.