Toyota Tacoma Quiz
Vf2cm Transfer

Transfer Shift Motor Control Circuit Circuit Open (P17A8)

In this manual: Vf2cm Transfer
Introduction — 15Maintenance — 8Audio / Video — 94Garage Door Opener — 7Navigation / Multi Info Display — 84Park Assist / Monitoring — 86Brake — 50Brake Control / Dynamic Control Systems — 165Parking Brake — 52gr-fks Charging — 252gr-fks Cooling — 212gr-fks Emission Control — 132gr-fks Engine Control — 322gr-fks Engine Mechanical — 332gr-fks Exhaust — 92gr-fks Fuel — 422gr-fks Ignition — 62gr-fks Intake — 72gr-fks Lubrication — 152gr-fks Starting — 38Ac60e Automatic Transmission / Transaxle — 146Axle — 19Clutch — 20Cruise Control — 168Differential — 50Drive Shaft — 6Propeller Shaft — 23Rc62f Manual Transmission / Transaxle — 34Suspension — 22Tire And Wheel — 39Vf2cm Transfer — 44Can Communication — 45Multiplex Communication — 20Power Distribution — 5Power Steering — 29Steering Column — 29Air Conditioning — 108Door Lock — 88Engine Hood / Door — 16Engine Immobiliser — 47Exterior — 55Horn — 5Interior — 18Interior Panel — 8Lighting — 93Meter / Gauge / Display — 31Mirror — 22Other System — 24Pre-collision — 40Seat — 52Seat Belt — 40Sliding Roof — 26Supplemental Restraint Systems — 139Theft Deterrent — 20Window / Glass — 53Wiper / Washer — 24
~1min read
DESCRIPTION

This DTC is output when an open circuit in the transfer shift motor drive circuit is detected.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

P17A8

Transfer Shift Motor Control Circuit Circuit Open
  • Diagnosis Condition: While switching between 2WD and H4 or while switching between H4 and L4 (transfer shift motor operating) with the ignition switch turned to ON
  • Malfunction Status: Open circuit in the transfer shift motor drive circuit
  • Malfunction Time: 0.03 seconds or more
  • Other: 1 trip detection logic
  • Wire harness and connector
  • 4 wheel drive control ECU
  • Transfer shift actuator assembly
WIRING DIAGRAM

Refer to DTC P17A9 (See page PROCEDURE ).

PROCEDURE

  1. CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - TRANSFER SHIFT ACTUATOR ASSEMBLY)

(a) Disconnect the F12 4 wheel drive control ECU connector.

(b) Disconnect the T4 transfer shift actuator assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F12-8 (TM1) - T4-2 (TM1)

Always

Below 1 Ω

F12-7 (TM2) - T4-1 (TM2)

Always

Below 1 Ω
NG

REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

  1. INSPECT TRANSFER SHIFT ACTUATOR ASSEMBLY (TRANSFER SHIFT MOTOR)

(a) Disconnect the T4 transfer shift actuator assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

2 (TM1) - 1 (TM2)

Always

1.5 to 10 Ω
Text in Illustration

*a

Component without harness connected

(Transfer Shift Actuator Assembly)
OK

REPLACE 4 WHEEL DRIVE CONTROL ECU
NG

REPLACE TRANSFER SHIFT ACTUATOR ASSEMBLY

Test yourself

A quick Toyota Tacoma quiz: every answer comes with an explanation and a link to the manual page.