Vehicle Interior
Position Initialization Incomplete (B2343)
DESCRIPTION
This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.
DTC Code | DTC Detection Condition | Trouble Area |
B2343 |
Sliding roof drive gear (sliding roof ECU) has not been initialized |
- Sliding roof switch
- Roof console box
- Harness and connector
- Sliding roof drive gear (sliding roof ECU)
|
WIRING DIAGRAM
PROCEDURE
INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
(a) Check that the sliding roof drive gear can be initialized (see page ).
OK:
Sliding roof drive gear can be initialized.
| NG |
 |
GO TO STEP 3 |
| OK |
 |
|
CHECK FOR DTC
(a) Clear the DTCs (see page ).
(b) Check for DTCs (see page ). Result
Result | Proceed to |
No DTC is output |
A |
DTC B2343 is output |
B |
| A |
 |
END |
| B |
 |
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
(a) Disconnect the W3 ECU connector. |
 |
(b) Disconnect the W7 roof console box connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
W3-1 (UP) - W7-6 (UP) |
Always |
Below 1 Ω |
W3-2 (DWN) - W7-5 (DOWN) |
Always |
Below 1 Ω |
W3-6 (OPN) - W7-4 (OPN) |
Always |
Below 1 Ω |
W3-7 (CLS) - W7-3 (CLS) |
Always |
Below 1 Ω |
W7-6 (UP) - Body ground |
Always |
10 kΩ or higher |
W7-5 (DOWN) - Body ground |
Always |
10 kΩ or higher |
W7-3 (CLS) - Body ground |
Always |
10 kΩ or higher |
W7-4 (OPN) - Body ground |
Always |
10 kΩ or higher |
W7-7 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
| OK |
 |
|
INSPECT SLIDING ROOF SWITCH
(a) Remove the sliding roof switch (see page ).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Switch Condition | Specified Condition |
1 (UP) - 5 (E) |
TILT switch is pressed to up |
Below 1 Ω |
1 (UP) - 5 (E) |
TILT switch is not pressed to up |
10 kΩ or higher |
2 (DWN) - 5 (E) |
TILT switch is pressed to down |
Below 1 Ω |
2 (DWN) - 5 (E) |
TILT switch is not pressed to down |
10 kΩ or higher |
4 (OPN) - 5 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
4 (OPN) - 5 (E) |
SLIDE switch is not pressed to open |
10 kΩ or higher |
3 (CLS) - 5 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
3 (CLS) - 5 (E) |
SLIDE switch is not pressed to close |
10 kΩ or higher |
| NG |
 |
REPLACE SLIDING ROOF SWITCH |
| OK |
 |
|
INSPECT ROOF CONSOLE BOX ASSEMBLY
(a) Remove the roof console box with sliding roof switch (see page ).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Switch Condition | Specified Condition |
6 (UP) - 7 (E) |
TILT switch is pressed to up |
Below 1 Ω |
6 (UP) - 7 (E) |
TILT switch is not pressed to up |
10 kΩ or higher |
5 (DOWN) - 7 (E) |
TILT switch is pressed to down |
Below 1 Ω |
5 (DOWN) - 7 (E) |
TILT switch is not pressed to down |
10 kΩ or higher |
4 (OPN) - 7 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
4 (OPN) - 7 (E) |
SLIDE switch is not pressed to open |
10 kΩ or higher |
3 (CLS) - 7 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
3 (CLS) - 7 (E) |
SLIDE switch is not pressed to close |
10 kΩ or higher |
| OK |
 |
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY |
| NG |
 |
REPLACE ROOF CONSOLE BOX ASSEMBLY |
|
Was this page helpful?