DESCRIPTION
If either the sliding function or tilt function does not operate, there may be a malfunction in the sliding roof switch circuit.
WIRING DIAGRAM
PROCEDURE
PERFORM ACTIVE TEST USING TECHSTREAM (SLIDING ROOF OPERATION)
(a) Select the Active Test, use the Techstream to generate a control command, and then check that the sliding roof operates (see page ). Sliding Roof
Tester Display | Test Part | Control Range | Diagnostic Note |
Slide Roof |
Operate sliding roof SLIDE CLOSE/TILT UP or SLIDE OPEN/TILT DOWN |
Clos/Up: Sliding roof SLIDE CLOSE or TILT UP operation occurs
Opn/Dwn: Sliding roof SLIDE OPEN or TILT DOWN operation occurs
OFF: Sliding roof is not operating |
- |
OK:
Sliding roof operates normally.
| NG |
 |
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
| OK |
 |
|
READ VALUE USING TECHSTREAM (SLIDING ROOF SWITCH)
(a) Use the Data List to check if the sliding roof switch is functioning properly (see page ). Sliding Roof
Tester Display | Test Part | Control Range | Diagnostic Note |
Open Switch |
Sliding roof open switch signal/ON or OFF |
ON: SLIDE switch is pressed to open
OFF: SLIDE switch is not pressed to open |
- |
Close Switch |
Sliding roof close switch signal/ON or OFF |
ON: SLIDE switch is pressed to close
OFF: SLIDE switch is not pressed to close |
- |
Up Switch |
Sliding roof up switch signal/ON or OFF |
ON: TILT switch is pressed to up
OFF: TILT switch is not pressed to up |
- |
Down Switch |
Sliding roof down switch signal/ON or OFF |
ON: TILT switch is pressed to down
OFF: TILT switch is not pressed to down |
- |
OK:
The Techstream displays as shown in the table according to the operation of each switch.
| OK |
 |
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
| NG |
 |
|
INSPECT SLIDING ROOF SWITCH
(a) Remove the sliding roof switch (see page ).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Switch Condition | Specified Condition |
1 (UP) - 5 (E) |
TILT switch is pressed to up |
Below 1 Ω |
1 (UP) - 5 (E) |
TILT switch is not pressed to up |
10 kΩ or higher |
2 (DWN) - 5 (E) |
TILT switch is pressed to down |
Below 1 Ω |
2 (DWN) - 5 (E) |
TILT switch is not pressed to down |
10 kΩ or higher |
4 (OPN) - 5 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
4 (OPN) - 5 (E) |
SLIDE switch is not pressed to open |
10 kΩ or higher |
3 (CLS) - 5 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
3 (CLS) - 5 (E) |
SLIDE switch is not pressed to close |
10 kΩ or higher |
| NG |
 |
REPLACE SLIDING ROOF SWITCH |
| OK |
 |
|
INSPECT ROOF CONSOLE BOX ASSEMBLY
(a) Remove the roof console box with sliding roof switch (see page ).
(b) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Switch Condition | Specified Condition |
6 (UP) - 7 (E) |
TILT switch is pressed to up |
Below 1 Ω |
6 (UP) - 7 (E) |
TILT switch is not pressed to up |
10 kΩ or higher |
5 (DOWN) - 7 (E) |
TILT switch is pressed to down |
Below 1 Ω |
5 (DOWN) - 7 (E) |
TILT switch is not pressed to down |
10 kΩ or higher |
4 (OPN) - 7 (E) |
SLIDE switch is pressed to open |
Below 1 Ω |
4 (OPN) - 7 (E) |
SLIDE switch is not pressed to open |
10 kΩ or higher |
3 (CLS) - 7 (E) |
SLIDE switch is pressed to close |
Below 1 Ω |
3 (CLS) - 7 (E) |
SLIDE switch is not pressed to close |
10 kΩ or higher |
| NG |
 |
REPLACE ROOF CONSOLE BOX ASSEMBLY |
| OK |
 |
|
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - ROOF CONSOLE BOX)
(a) Disconnect the W3 ECU connector. |
 |
(b) Disconnect the W7 switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection | Condition | Specified Condition |
W3-1 (UP) - W7-6 (UP) |
Always |
Below 1 Ω |
W3-2 (DWN) - W7-5 (DOWN) |
Always |
Below 1 Ω |
W3-6 (OPN) - W7-4 (OPN) |
Always |
Below 1 Ω |
W3-7 (CLS) - W7-3 (CLS) |
Always |
Below 1 Ω |
W7-6 (UP) - Body ground |
Always |
10 kΩ or higher |
W7-5 (DOWN) - Body ground |
Always |
10 kΩ or higher |
W7-3 (CLS) - Body ground |
Always |
10 kΩ or higher |
W7-4 (OPN) - Body ground |
Always |
10 kΩ or higher |
W7-7 (E) - Body ground |
Always |
Below 1 Ω |
| OK |
 |
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) |
| NG |
 |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|