Toyota Venza Quiz
Heating / Air Conditioning

Air Conditioning Amplifier

In this manual: Heating / Air Conditioning
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
Components COMPONENTS ILLUSTRATION
Installation INSTALLATION PROCEDURE

1. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY

(a) Install the air conditioning amplifier assembly with the 2 screws.

(b) Connect each connector.

NOTICE:

Be careful when installing the air conditioning amplifier assembly. If the air conditioning amplifier assembly is dropped, replace it with a new one.

2. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


3. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


4. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side and the LH side (See page ).


5. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure for the RH side and the LH side (See page ).


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


Removal REMOVAL PROCEDURE

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


2. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure for the RH side and the LH side (See page ).


3. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure for the RH side and the LH side (See page ).


4. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


5. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


6. REMOVE AIR CONDITIONING AMPLIFIER ASSEMBLY

(a) Disconnect each connector.

(b) Remove the 2 screws and air conditioning amplifier assembly.

NOTICE:

Be careful when removing the air conditioning amplifier assembly. If the air conditioning amplifier assembly is dropped, replace it with a new one.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.