Toyota Venza Quiz
Door Lock

Inspection

In this manual: Door Lock
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
INSPECTION PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → Terminal 4 (DL)

Battery negative (-) → Terminal 1 (UL)

Locks

Battery positive (+) → Terminal 1 (UL)

Battery negative (-) → Terminal 4 (DL)

Unlocks
Text in Illustration

*1

Component without harness connected

(Rear Door Lock Assembly LH)

*2

Lock

*3

Unlock

If the result is not as specified, replace the rear door lock assembly LH.

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (LSSR) - 9 (E)

Locked

10 kΩ or higher

6 (LSSR) - 9 (E)

Unlocked

Below 1 Ω
Text in Illustration

*1

Component without harness connected

(Rear Door Lock Assembly LH)

*2

Lock

*3

Unlock

If the result is not as specified, replace the rear door lock assembly LH.

2. INSPECT REAR DOOR LOCK ASSEMBLY RH

(a) Check the operation of the door lock motor.

(1) Apply battery voltage and check the operation of the door lock motor.

OK:

Measurement Condition

Specified Condition

Battery positive (+) → Terminal 4 (L)

Battery negative (-) → Terminal 1 (DL)

Locks

Battery positive (+) → Terminal 1 (DL)

Battery negative (-) → Terminal 4 (L)

Unlocks
Text in Illustration

*1

Component without harness connected

(Rear Door Lock Assembly RH)

*2

Lock

*3

Unlock

If the result is not as specified, replace the rear door lock assembly RH.

(b) Check the operation of the unlock detection switch.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (LSSR) - 9 (E)

Locked

10 kΩ or higher

6 (LSSR) - 9 (E)

Unlocked

Below 1 Ω
Text in Illustration

*1

Component without harness connected

(Rear Door Lock Assembly RH)

*2

Lock

*3

Unlock

If the result is not as specified, replace the rear door lock assembly RH.

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.