Toyota Venza Quiz
Brake Control / Dynamic Control Systems

Installation

In this manual: Brake Control / Dynamic Control Systems
Introduction — 15Maintenance — 8Audio / Video — 102Garage Door Opener — 8Navigation / Multi Info Display — 81Park Assist / Monitoring — 50Brake (front) — 7Brake (rear) — 7Brake Control / Dynamic Control Systems — 79Brake System (other) — 28Parking Brake — 22Axle And Differential — 44Drive Shaft / Propeller Shaft — 24Mf1a Transfer / 4wd / Awd — 46U660e Automatic Transmission / Transaxle — 1241ar-fe Cooling — 311ar-fe Emission Control — 101ar-fe Engine Control — 1331ar-fe Engine Mechanical — 441ar-fe Fuel — 311ar-fe Intake / Exhaust — 211ar-fe Lubrication — 111ar-fe Starting — 16Cruise Control — 241ar-fe Battery / Charging — 162gr-fe Battery / Charging — 17Networking — 67Power Distribution — 8Power Assist Systems — 34Steering Column — 37Steering Gear / Linkage — 29Alignment / Handling Diagnosis — 4Front Suspension — 39Rear Suspension — 35Tire / Wheel — 4Tire Pressure Monitoring — 35Door / Hatch — 83Exterior Panels / Trim — 56Horn — 4Lighting (ext) — 89Mirror (ext) — 36Sliding Roof / Convertible — 26Window / Glass — 87Wiper / Washer — 30Door Lock — 85Heating / Air Conditioning — 82Interior Panels / Trim — 20Lighting (int) — 37Meter / Gauge / Display — 41Mirror (int) — 9Power Outlets (int) — 10Seat — 84Seat Belt — 43Supplemental Restraint Systems — 131Theft Deterrent / Keyless Entry — 155
~2min read
010203040508.56N·mlb·ft
Tightening torque found on this page
INSTALLATION CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the LH side and RH side.
  • The following procedure is for the LH side.
  • If the sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
PROCEDURE

1. INSTALL FRONT SPEED SENSOR

(a) Install the resin clamp and front speed sensor with the bolt.

Torque:

8,5 N·m {87 kgf·cm, 75 in·lbf}

NOTICE:

  • Prevent foreign matter from attaching to the front speed sensor tip.
  • Firmly insert the front speed sensor body into the knuckle before tightening the bolt.
  • After installing the front speed sensor to the knuckle, make sure that there is no clearance between the front speed sensor stay and knuckle. Also make sure that no foreign matter is stuck between the parts.
  • Before installing the clamp, firmly insert the points of the clamp into the installation holes.
Text in Illustration

*1

Resin Clamp

(b) Temporarily install the No. 1 sensor clamp.

NOTICE:

Be sure to insert the No. 1 sensor clamp claw into the stopper hole while installing the No. 1 sensor clamp.

Text in Illustration

*1

Stopper Hole

*2

No. 1 Sensor Clamp

(c) Install the front brake flexible hose and No. 1 sensor clamp together to the shock absorber with the bolt.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

NOTICE:

  • Do not twist the wire harness for the front speed sensor when installing it.
  • A bolt tightens the brake flexible hose and front speed sensor together. Make sure that the flexible hose is positioned over the front speed sensor.
Text in Illustration

*1

Front Brake Flexible Hose

*2

No. 1 Sensor Clamp

(d) Install the No. 2 sensor clamp to the body with the bolt.

Torque:

8 N·m {82 kgf·cm, 71 in·lbf}

Text in Illustration

*1

No. 2 Sensor Clamp

(e) Install the 2 clamps and connect the front speed sensor connector.

2. INSTALL FRONT FENDER LINER LH


3. INSTALL FRONT FENDER OUTSIDE MOULDING LH


4. INSTALL FRONT WHEEL

Torque:

103 N·m {1050 kgf·cm, 76 ft·lbf}

5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


6. CHECK FOR SPEED SENSOR SIGNAL

HINT:

(See page )

Test yourself

A quick Toyota Venza quiz: every answer comes with an explanation and a link to the manual page.