Differential
Assembly Overview - Differential

- Drive shaft seal, left
- replace with manual transmission installed
- Transmission housing
- overhaul
- Assignment → Electronic Parts Catalog (ETKA)
- Stop washer
- replace after removal
- Shoulder faces away from housing
- Outer race/tapered roller bearing
- Pull off
- Press in
- Bearing inner race/tapered roller bearing
- pull off
- Press on
- Differential housing
- with differential bevel gears, thrust washer assembly, differential bevel gear shaft and final drive gear
- Remove differential bevel gears, thrust washer assembly and differential bevel gear shaft
- Install differential bevel gears, thrust washer assembly and differential bevel gear shaft
- Bearing inner race/tapered roller bearing
- pull off
- Press on
- Outer race/tapered roller bearing
- press out
- Press in
- Adjusting shim
- for differential
- Determine thickness
- Stop washer
- replace after removal
- Shoulder faces away from housing
- Clutch housing
- overhaul
- Drive shaft seal, right
- replace with manual transmission installed
Disassembling and assembling differential

Required Special Tools, Test and Measuring Equipment and Auxiliary Items
- Clamping block -VW 313-
- Gearbox holder -T10484-
- Internal puller 46...58 mm, e.g. -Kukko 21/7-
- -4- Counter support, e.g. -Kukko 22/2-
- Counterhold -T10140- or flat steel 8 x 280
- Pressure ram -VW 408 A-
- Pressure washer -VW 510-
- Pressure plate -VW 401-
- Pressure plate -VW 402-

- Tapered roller bearing puller -V.A.G 1582-
- Gripping piece -V.A.G 1582/4-
- Spacer sleeve -VW 472/2-
- Pressure piece -3002-
- Pressure ram -VW 412-
- Pressure piece -VW 454-

- Drift tube -32 - 109-
- 2 x wedge -T10161-
- Pressure ram -VW 411-
- Drift punch -2074-
- Socket -3156 A-
![]()
Note
- Heat bearing inner races/tapered roller bearings to 100 °C before installation.
- Replace both tapered roller bearings together.
- When replacing the tapered roller bearings, the differential housing, the transmission housing or the clutch housing, the differential must be adjusted.
Pull the outer race/tapered roller bearing out of the clutch housing
- Counter support, e.g. -Kukko 22/2-
- Internal puller 46 ... 58 mm, e.g. -Kukko 21/7-
- Clamp the internal puller firmly behind the outer race/tapered roller bearing.

Install new collapsible spacer (shown here together with the transmission housing)
Installation position: the shoulder -arrow- points away from housing -A-

Press the outer race/tapered roller bearing into the clutch housing
- Place counterholder -T10140- on pressure plate -VW 402-.
- The clutch housing is held horizontally with counterholder -T10140-.
A flat bar 8 x 280 can be used instead of counterholder -T10140-.
The large shoulder of pressure washer -VW 510- points toward drift -VW 408 A-.

Pull off the inner race of the tapered roller bearing
- Before assembling the puller, place spacer sleeve -VW 472/2- and pressure piece -3002- onto the differential housing.
![]()
Note
Pulling off both inner races/tapered roller bearings of the differential housing is identical.

Press on the inner race of the tapered roller bearing
![]()
WARNING!
Wear protective gloves!
- Heat the inner race of the tapered roller bearing to approx. 100 ºC before pressing it on.
![]()
Note
Pressing on both inner races/tapered roller bearings of the differential housing is identical.

Pull outer race/tapered roller bearing out of transmission housing
- Counter support, e.g. -Kukko 22/2-
- Internal puller 46 ... 58 mm, e.g. -Kukko 21/7-
- Clamp the internal puller firmly behind the outer race/tapered roller bearing.

Install new collapsible spacer
Installation position: the shoulder -arrow- points away from housing -A-

Press outer race/tapered roller bearing into transmission housing
The large shoulder of pressure washer -VW 510- points toward drift -VW 412-.
- Support the transmission housing directly below the bearing seat with drift tube -32 - 109-.
- The transmission housing is held horizontally with wedges -T10161-.
Pull off the inner race of the tapered roller bearing
![]()
Note
Pulling off both inner races/tapered roller bearings of the differential housing is identical.
Press on the inner race of the tapered roller bearing
![]()
Note
Pressing on both inner races/tapered roller bearings of the differential housing is identical.
![]()
WARNING!
Wear protective gloves!
- Heat the inner race of the tapered roller bearing to approx. 100 ºC before pressing it on.

Remove differential bevel gears, thrust washer assembly and differential bevel gear shaft
- Remove the circlip for the differential bevel gear shaft.
- Remove the differential bevel gear shaft.
- Drive out the differential bevel gear shaft with a plastic hammer and drift pin -2074-.
If interference fit is high, press out the differential bevel gear shaft
- Then have a second mechanic hold the differential in position.
The teeth of socket -3156 A- point toward the differential.
Do not damage the teeth.

Install differential bevel gears, thrust washer assembly and differential bevel gear shaft
- Install the thrust washer set with transmission oil.
- Install both large differential bevel gears.
- Hold the upper large differential bevel gear in position.
- Install both small differential bevel gears offset by 180º and swing them into place.
- Drive the differential bevel gear shaft into its end position -arrow- and secure it with the circlip.

Adjusting the differential

Required Special Tools, Test and Measuring Equipment and Auxiliary Items
- Clamping block -VW 313-
- Gearbox holder -T10484-
- Gauge block plate -VW 385/17-
- Universal dial gauge holder -VW 387-
- Pressure plate -VW 402-
- Pressure plate -VW 401-
- Drift -VW 408-
- Pressure washer -VW 510-
- Torque Wrench -V.A.G 1331-
- Dial gauge -VAS 6080A-
- Dial gauge extension 30 mm
- -1- Internal puller -Kukko 21/7-
- -4- Counter support -Kukko 22/2-
The differential must be readjusted if the following components are replaced:
- Transmission housing
- Clutch housing
- Differential housing
- Differential tapered roller bearings
Requirement:
- Sealing surfaces of clutch housing and transmission housing must be cleaned of sealant.
- Both inner races for the tapered roller bearings are pressed onto the differential housing.
- New collapsible spacer is installed in the transmission housing.
- The outer race/tapered roller bearing (gear side) is pressed into the transmission housing.
Adjustment overview

- Press the outer race/tapered roller bearing (opposite the gear side) into the clutch housing without shim and without collapsible spacer.
- Install the differential in the transmission housing.
- Fit the clutch housing and tighten the 5 bolts to the specified tightening torque.

- Mount the dial gauge and set it to "0" with 1 mm preload.
- Dial gauge extension 30 mm
- Turn the differential before measuring so the tapered roller bearings seat. Set the dial gauge to "0" with 1 mm preload.
- Move the differential up and down, read the play on the dial gauge and note it. (Example: 1.50 mm)
Determine shim
The specified bearing preload is achieved when a constant value for crush (0.35 mm) is added to the measured value.
Example:

Measured value - 1.30 mm
+ Crush (constant value) - 0.20 mm
Thickness of shim = - 1.50 mm
- Remove the clutch housing and pull the outer race/tapered roller bearing out of the clutch housing.
- Counter support, e.g. -Kukko 22/2-
- Internal puller 46 ... 58 mm, e.g. -Kukko 21/7-
- Assign the shim(s) using the Electronic Parts Catalogue (ETKA).
Different tolerances allow the required shim thickness to be measured precisely.
If the measured shim thickness is greater than listed in the Electronic Parts Catalogue (ETKA), 2 shims corresponding to the measured value can be installed.
- Install new collapsible spacer

- Insert the shim of the determined thickness (in the example 1.50 mm) and press the outer race/tapered roller bearing back into the clutch housing.
- Fit the clutch housing and tighten the bolts to the specified tightening torque.

Adjustment overview
![]()
Note
Readjustment of the input shaft, output shaft or differential is only required if parts are replaced that directly affect the adjustment of the transmission. To avoid unnecessary adjustment work, observe the following table:
