Brake system

Brake pedal

26steps
~156min
4/5difficulty
010203040502518N·mlb·ft
Tightening torque found on this page
Done 0 of 26

Remove and install bearing bracket

Remove and install pedal cluster, left-hand drive

Removing:

- Unscrew bolts -1- and remove footwell trim -2-.

- Disconnect the connector from the accelerator pedal position sensor.

- Separate the brake pedal from the brake booster.

VW UP. Bremsanlagen

- Unscrew the hex nuts -arrows- from the pedal cluster.

- Remove the pedal cluster.

Installing:

Install in reverse order.

- Clip the brake pedal onto the brake booster.

VW UP. Bremsanlagen

Tightening torque:

Hex nut, pedal cluster to brake booster/bulkhead 25 N·m

  • Use new nuts!

Remove and install pedal cluster, right-hand drive

Removing:

- Remove the side cover of the dashboard → Body assembly work interior.

- Remove the driver side dashboard cover → Body assembly work interior.

- Separate the brake pedal from the brake booster.

- Remove the crash brace → Chassis, axles, steering.

- Disconnect the connector from the accelerator pedal position sensor.

- Unscrew the hex nuts -arrows- from the pedal cluster.

- Remove the pedal cluster.

Installing:

Install in reverse order.

- Clip the brake pedal onto the brake booster.

VW UP. Bremsanlagen

Tightening torques:

Hex nut, pedal cluster to brake booster/bulkhead - 25 N·m

  • Use new nuts!

Crash brace to steering → Chassis, axles, steering.

Remove and install brake pedal

Remove and install brake pedal, left-hand drive

Removing:

- Separate the brake pedal from the brake booster.

- Unscrew hex nut -1-.

- Pull out hex bolt -2-.

- Remove the brake pedal.

Installing:

Install in reverse order.

- Clip the brake pedal onto the brake booster.

VW UP. Bremsanlagen

Remove and install brake pedal, right-hand drive

Removing the brake pedal separately in the vehicle is not possible, as the hex bolt cannot be pulled out fully.

- First remove the pedal cluster, then remove the brake pedal.

Connect brake pedal to brake booster

- Hold the ball socket of the push rod in front of the receptacle and press the brake pedal in the direction of the brake booster until the ball socket audibly snaps in.

- Check that the latching engages by pulling briefly on the brake pedal.

VW UP. Bremsanlagen

Separating brake pedal from brake booster

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Release tool -T40136-
VW UP. Bremsanlagen

- First press the brake pedal toward the brake booster and hold it.

  1. Brake pedal
  2. Push rod
  3. Retaining lugs

- Insert release tool -T40136- and pull toward the driver's seat while holding counter to the brake pedal (the brake pedal must not move rearward at this moment). This pushes the retaining lugs -3- out of the socket of the push rod ball joint -2-.

Illustration shows separating the brake pedal from the brake booster with the pedal box removed, for better clarity.

- Pull the release tool -T40136- and the brake pedal together toward the driver's seat. (This pulls the brake pedal off the push rod ball joint.)

VW UP. Bremsanlagen

Assembly overview - brake pedal

Assembly overview - brake pedal, left-hand drive


WARNING!

Do not shorten the brake pedal travel with additional floor coverings.

The brake light switch is located on the brake master cylinder.

VW UP. Bremsanlagen

  1. Pedal box
    • Remove and install
  2. Hex bolt
  3. Hex nut, self-locking, 25 N·m
    • replace after every removal.
  4. Brake pedal
    • Remove and install
  5. Cap
  6. Bearing shell
  7. Socket
    • for the ball joint of the brake booster push rod
  8. Hex nut, self-locking, 25 N·m
    • replace after every removal.
  9. Bearing bush
  10. Bearing pin

Assembly overview - brake pedal, right-hand drive


WARNING!

Do not shorten the brake pedal travel with additional floor coverings.

The brake light switch is located on the brake master cylinder.

VW UP. Bremsanlagen

  1. Cover
  2. Pedal box
    • Remove and install
  3. Hex nut, self-locking, 25 N·m
    • replace after every removal.
  4. Hex nut, self-locking, 25 N·m
    • replace after every removal.
  5. Brake pedal
    • Remove and install
  6. Cap
  7. Crash brace
  8. Hex bolt
    • Tightening torques → Chassis, axles, steering
  9. Bearing shell
  10. Socket
    • for the ball joint of the brake booster push rod
  11. Hex bolt
  12. Bearing bush
  13. Bearing pin