Brake system

Parking brake

11steps
~66min
3/5difficulty
010203040502317N·mlb·ft
Tightening torque found on this page
Done 0 of 11

Adjusting parking brake

Readjustment is only required when replacing the brake cables, the brake carrier, or after replacing the brake pads.

- Remove center console → Body assembly work, interior.

- The foot brake must be functional and bled.

  • The parking brake lever is in the basic position (released).

- Loosen the brake cables using adjusting nut -arrow A-.

- Apply the foot brake firmly three times.

- Tension the brake cables using adjusting nut -arrow A- until the parking brake lever returns to the basic position on its own (see note).


Note

From the basic position, pull the parking brake lever up to just before the first notch. Release the parking brake lever. The parking brake lever must return fully to its stop on its own.

- Pull the parking brake lever up 2 notches.

- Tighten adjusting nut -arrow A- until neither wheel can be turned by hand.

The adjusting nut -arrow A- must be threaded over the end of the pull rod -1-.

- Release the parking brake and check that both wheels turn freely. If necessary, back off the adjusting nuts slightly.

- Install center console → Body assembly work, interior.

After readjustment, the automatic adjustment of the rear brake makes readjusting the parking brake no longer necessary.

VW UP. Bremsanlagen

Removing and installing rear brake cable

Removing:

- Remove center console → Body assembly work, interior.

- Release the parking brake.

- Loosen the adjusting nut -arrow- until the brake cable can be unhooked from the equalizer bracket.

- Raise the vehicle.

- Remove wheel.

- Remove brake drum; first retract the brake.

VW UP. Bremsanlagen

- Unhook the brake cable from the parking brake lever.

- Pull the brake cable out of the brake carrier.

VW UP. Bremsanlagen

- Unclip the brake cable -1- from the bracket on the rear axle housing -arrow-.

VW UP. Bremsanlagen

- Unhook the brake cable from the brackets -arrows-.

VW UP. Bremsanlagen

- Pull the brake cable -1- out of the guide tube -2- in the direction of the arrow.

Installing:

VW UP. Bremsanlagen

- Push the brake cable -1- into the guide tube -2- in the direction of the arrow.

- Insert the brake cable into the brake carrier.

VW UP. Bremsanlagen

- Hook the brake cable into the parking brake lever.

- Install brake drum.

VW UP. Bremsanlagen

- Clip the brake cable -1- into the bracket on the rear axle housing -arrow-.

- The clamping ring on the brake cable must be centered in the clip.

VW UP. Bremsanlagen

- Hook the brake cable into the brackets -arrows-.

- Push the brake cable through the guide tube.

- Hook the brake cable into the equalizer bracket.

VW UP. Bremsanlagen

- Tension the brake cable using adjusting nut -arrow-.

- Install wheels.

Tightening torque for wheel bolts → Chassis, axles, steering.

- Adjust parking brake.

- Install center console → Body assembly work, interior.

VW UP. Bremsanlagen

Assembly overview - parking brake

VW UP. Bremsanlagen

  1. Push-button
    • pull off
    • is destroyed when pulled off, must be replaced
    • push onto the push rod of the parking brake lever and check by lightly pulling whether both locking lugs are engaged.
  2. Trim for parking brake lever
    • for removal, first pull off the push-button
    • Pry up the release tab in the rear lower grip area with a screwdriver.
    • then pull forward.
  3. Adjusting nut
    • Adjusting parking brake
  4. Equalizer bracket
  5. Parking brake lever
    • before removal, remove center console → Body assembly work, interior
  6. Hex nut, 23 N·m
  7. Parking brake switch -F321-
  8. Rubber grommet
  9. Guide tube, right
  10. Guide tube, left
  11. Brake cables
    • Remove and install

Pull off push button


Note

If destroyed when removing, must be replaced.

VW UP. Bremsanlagen