Brake system

Rear wheel brake

28steps
~168min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 28

Removing and installing brake shoes

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Hook -3438-

After working on the rear wheel brake:

  • Release parking brake.
  • Press brake pedal firmly once.

Assembly overview - brake shoes:

VW UP. Bremsanlagen

VW UP. Bremsanlagen

  1. Spring plate
    • to remove, press against compression spring and turn 90º.
  2. Compression spring
  3. Brake shoe with parking brake lever
    • Remove and install
    • Adjusting parking brake
  4. Return spring, upper
    • unhook using hook -3438-.
  5. Return spring, lower
    • Grease contact surface with solid lubricant paste ET no. G 000 650.
  6. Tension spring
  7. Brake shoe

Brake linings are also available without brake shoes.

  1. Filler Cap
    • remove to check brake lining thickness.
  2. Roll pin
  3. Brake carrier
  4. Torx bolt, 8 N·m
  5. Wheel brake cylinder
    • Check for leaks
  6. Wedge
    • to remove and install brake drum, press wedge upward through a wheel bolt hole
  7. Push rod
    • Grease contact surface with solid lubricant paste ET no. G 000 650.
  8. Contact spring
    • unhook using hook -3438-.

Removing:

- Remove wheels.

- Remove brake drum; first retract the brake.

- Remove wheel hub -2- → Suspension, axles, steering.

- Remove spring plates with compression springs.

VW UP. Bremsanlagen

- Pry brake shoes out in direction of arrow behind lower support plate using a screwdriver.

- Place brake shoes on lower support plate.

- Unhook lower return spring.

- Unhook brake cable.

- Remove brake shoes.

- Clamp brake shoes in vise.

VW UP. Bremsanlagen

- Remove tension spring -1- for wedge -2-.

- Remove upper return spring -3- using hook -3438-.

VW UP. Bremsanlagen

- Unhook contact spring -1- using hook -3438-.

- Remove push rod -2- and wedge -3- from brake shoe.

Cleaning:


WARNING!

Do not blow out brake system with compressed air; the resulting dust is harmful to health!

Only use denatured alcohol to clean the brake system.

Installing:

VW UP. Bremsanlagen

- Hook contact spring -1- into push rod -2- using hook -3438-.

- At the same time, insert wedge -3-.

Installation position:

Raised area -arrow- must remain visible during installation.

- Insert brake shoe with brake lever into push rod.

VW UP. Bremsanlagen

- Hook return spring -3- in using hook -3438-.

- Hook tension spring -1- in for wedge -2-.

- Place brake shoes on brake carrier.

- Hook brake cable onto brake lever.

- Place brake shoes onto pistons of wheel brake cylinder.

VW UP. Bremsanlagen

- Insert lower return spring and pry brake shoe behind lower support.

- Insert compression spring with spring plate.

- Install wheel hub -2- → Suspension, axles, steering.

- Install brake drum.

- Install wheels.

Tightening torque for wheel bolts → Chassis, axles, steering.

- Press foot brake firmly once.

- Adjust parking brake.

VW UP. Bremsanlagen

Tightening torques:

Torx bolt, brake drum to wheel hub - 8 N·m

Resetting drum brake

- Through a threaded hole of the wheel bolts in the brake drum, press wedge upward with a screwdriver.

VW UP. Bremsanlagen

Assembly overview - rear wheel brake


Note

  • After replacing wheel brake cylinder, brake carrier and brake shoes, press brake pedal firmly once while vehicle is stationary so that brake shoes seat correctly for operating condition.
  • To extract brake fluid from brake fluid reservoir, use Brake Filling and Bleeding Unit -VAS 5234-.
  • Before removing a wheel brake cylinder, brake carrier, or disconnecting a brake line from the wheel brake cylinder, install Brake Pedal Depressor -V.A.G 1869/2- (relieve pressure first).
VW UP. Bremsanlagen

  1. Axle body
  2. Torx bolt, 8 N·m
  3. ABS wheel speed sensor
    • Before installing sensor, clean inner surface of bore and coat with hot-bolt paste G 052 112 A3.
  4. Brake line, 14 N·m
  5. Stub axle
  6. Brake cable
    • Adjusting parking brake
  7. Hex bolt
    • Tightening torques → Chassis, axles, steering
  8. Torx bolt, 8 N·m
  9. Brake drum
    • Brake drum diameter, 200 mm
    • Wear limit 201.5 mm
    • Before removing brake drum, reset brake
    • Clean thoroughly and check for wear, damage, dimensional accuracy, and proper braking surface.
  10. Cap
    • Press off and drive in → Suspension, axles, steering
  11. 12-point nut, self-locking
    • Replace after every removal → Suspension, axles, steering
  12. Wheel hub with wheel bearing
    • Removing and installing → Suspension, Axles, Steering
  13. Brake carrier with brake shoes
    • Minimum pad thickness 2.5 mm
    • Check thickness
    • Before removing brake drum, reset brake