Front Windshield Washer System
Assembly Overview - Front Windshield Washer System

- Angled fitting
- Connection to right front windshield washer nozzle
- Overview of hose couplings for washer fluid lines
- Right front windshield washer nozzle
- Remove and install
- adjust
- Angled fitting
- Connection to left front windshield washer nozzle
- Overview of hose couplings for washer fluid lines
- Left front windshield washer nozzle
- Remove and install
- adjust
- Y-piece
- Routing of the washer fluid line to the front windshield washer nozzles
- Hose
- Repairing washer fluid lines
- Connecting pipe with filler neck to reservoir
- is removed and installed together with the reservoir
- Washer fluid reservoir
- Remove and install
- Tightening torque, reservoir mounting bolt to body: 8 N·m
- Front and rear windshield washer pump -V59-
- Remove and install
- Angled connector
- Connection to front and rear windshield washer pump -V59-
- Overview of hose couplings for washer fluid lines
Removing and installing washer fluid reservoir
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Remove the front bumper cover. → Body Assembly Work Exterior.
- Press the lock -arrow- and pull the filler neck -1- upward out of the holder on the radiator support.

- Pull the front and rear windshield washer pump -V59- -2- with connected lines upward out of the reservoir -5-.
- Catch any washer fluid that runs out in a suitable container.

- Release the retainer of the connecting pipe with filler neck -2- from the body shell.
- Unscrew the mounting bolt -5- and pull the reservoir -4- out of the guide -3- toward the rear in the -arrow direction-.
- Remove the reservoir -4- together with the connecting pipe with filler neck -1- from the vehicle.
Installing
Installation is carried out in the reverse order of removal, observing the following:

- Guide the connecting pipe with filler neck -1- upward through the body shell.
- Slide the reservoir -4- onto the guide -3- and tighten it with bolt -5-.
- Secure the connecting pipe with filler neck -1- in the body shell -2- and engage the filler neck in the holder on the radiator support until it clicks.
Tightening torques
- "Assembly Overview - Front Windshield Washer System"

Removing and installing washer pump
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Loosen the front left wheel housing liner in the front area. → Body Assembly Work Exterior.
- Turn the retaining clips on the angled connectors -3- and -4- to unlock them and pull them off the front and rear windshield washer pump -V59- -2-.
- Catch any washer fluid that runs out in a suitable container.
- Pull the front and rear windshield washer pump -V59- -2- upward out of the reservoir -5-.
- Unlock connector -1- and disconnect it.
Note
To prevent the washer fluid lines from being connected to the front and rear windshield washer pump -V59- in the wrong positions, the connections on the pump and the hose lines are color-coded. When installing, push each hose connector onto the pump connection of the matching color.
Installing
Installation is performed in the reverse order.

Removing and installing washer nozzles
Removing
- Switch off ignition and all electrical consumers and remove the ignition key.
- Press the nozzle upward -arrow A- and swivel it out of the hood at the bottom -arrow B-.

- Unlock retaining clip -3- and pull hose connection -2- off the washer nozzle.
- Unlock and disconnect the plug connector -1- if equipped, and remove the washer nozzle.
Installing

- Connect the plug connector -1- if equipped.
- Push hose connection -2- onto the washer nozzle and engage retaining clip -3- until it locks.
- Insert the washer jet, starting at the top, into the mounting opening until it audibly clicks into place.
- Adjust the washer jets.

Adjusting washer jets
Note
If the spray pattern is uneven due to contamination in the washer jet, remove the washer jet and flush it with water against the spray direction. Subsequently blowing out against the spray direction with compressed air is permitted. Do not use any objects to clean the washer jets!
Adjusting windshield washer jets: "Instandhaltung genau genommen".