Electrical system

Rear window wiper system

9steps
~54min
2/5difficulty
01020304050129N·mlb·ft
Tightening torque found on this page
Done 0 of 9

Assembly overview - Rear window wiper system

VW UP. Elektrische Anlage

  1. Cover cap
  2. Mounting nut
    • Tightening torque: 12 N·m
  3. Jointless wiper blade
    • Remove and install
  4. Wiper arm
    • Remove and install
    • Adjusting park position
  5. Gasket
    • in the rear window
  6. Rear window wiper motor -V12-
    • Remove and install
  7. Spacer
  8. Rubber ring
  9. Mounting nut M6 with washer
    • Tightening torque: 8 N·m

Remove and Install Wiper Blade

Removing


Caution!

Risk of damage to the wiper blade.

The jointless wiper blades are very flexible. Only hold the wiper blades in the area of the wiper blade attachment when lifting them off the windshield.

- Fold up the wiper arm -2-.

- Press button -1- and slide the wiper blade -3- out of the holder in the -arrow- direction.

Installing

Installation is carried out in the reverse order, observing the following:

The wiper blade must audibly click into the wiper arm.

VW UP. Elektrische Anlage

Removing and installing wiper arm

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Wiper arm tool set -T10369-
VW UP. Elektrische Anlage

  • Torque Wrench -V.A.G 1331-

Removing

- Switch the ignition on.

- Press "rear wiper" and let the wiper arm run to the end position.

- Switch the ignition off.

- Remove the ignition key.

VW UP. Elektrische Anlage

- Fold up the cover cap -1- of the rear wiper and unclip it.

- Loosen the mounting nut -arrow-, without fully unscrewing it.

VW UP. Elektrische Anlage

- Attach puller -T10369/5- to the wiper arm -2-.

- Place pressure piece -3- on the wiper arm shaft.

- Turn screw -1- clockwise until the wiper arm is pulled off the wiper arm shaft.

- Unscrew nut -4- completely and remove the wiper arm.

Installing

Installation is carried out in the reverse order, observing the following:

VW UP. Elektrische Anlage

- Push the wiper arm onto the wiper arm shaft in the approximate park position and screw on the mounting nut -arrow- hand-tight.

- Adjust the wiper arm.

VW UP. Elektrische Anlage

Adjusting wiper arm

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque Wrench -V.A.G 1331-

- To adjust the park position, align the wiper blade tip with the lowest heating wire of the rear window heating.

- If necessary, adjust the rear wiper park position by offsetting the wiper arm.

- Tighten the nut.

Tightening torques

  • "Assembly overview - Rear window wiper system"
VW UP. Elektrische Anlage

Removing and installing rear window wiper motor -V12-

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Torque Wrench -V.A.G 1331-

Removing

- Remove the wiper arm.

- Remove the tailgate trim panel. → Body assembly work interior.

- Unlock connector -1- and disconnect it.

- Unscrew the mounting nuts -arrows-.

- Remove rear window wiper motor -V12--4-.

Installing

Installation is carried out in the reverse order of removal, observing the following:

- If necessary, wet the inside of the seal in the rear window with a rubber- and plastic-compatible lubricant (e.g. polyethylene glycol).

VW UP. Elektrische Anlage

- Check that the seal is correctly seated in the rear window opening. The marking -1- on the seal must match the marking -2- on the rear window.

Tightening torques

  • "Assembly overview - Rear window wiper system"
VW UP. Elektrische Anlage