3-cyl. injection engine, timing belt drive (4-valve)

Oil filter/oil pressure switch

~2min read

Removing and installing oil pressure switch -F1-

Required special tools, testers and equipment, and auxiliary items

  • Torque wrench -V.A.G 1331-

Removing

Damage from leaking engine oil. Cover alternator with a rag.

- Disconnect connector -1-.


Note

  • The oil pressure switch is sealed with a captive sealing ring.
  • The sealing ring is not suitable for repeated use. The oil pressure switch must be replaced after removal.
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew oil pressure switch -2- from cylinder head.

Installing

- Screw oil pressure switch -2- into cylinder head and tighten to specified tightening torque.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Attach connector -1-.

- Remove rag from alternator.

Oil pressure switch tightening torque

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)


Checking oil pressure and oil pressure switch

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Required special tools, testers and equipment, and auxiliary items

  • Oil pressure tester -V.A.G 1342-
  • Voltage tester -V.A.G 1527 B-
  • Measuring adapter set -V.A.G 1594C-


Note

Function test and repair of visual and audible oil pressure warning: → Wiring diagrams, troubleshooting electrical and installation locations

Test procedure

Damage from leaking engine oil. Cover alternator with a rag.

- Disconnect connector -1-.

- Unscrew oil pressure switch -F1- from cylinder head.


Note

  • The oil pressure switch is sealed with a captive sealing ring.
  • The sealing ring is not suitable for repeated use. The oil pressure switch must be replaced after removal "Removing and installing oil pressure switch -F1-".
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Screw oil pressure switch -F1- into tester.

- Screw tester into cylinder head in place of oil pressure switch.

- Connect brown lead of tester to ground (-).

- Connect voltage tester -V.A.G 1527B- with auxiliary leads from measuring adapter set -V.A.G 1594C- to battery positive (+) and oil pressure switch.

- Start engine and slowly increase speed. At 0.3 ... 0.6 bar gauge pressure the LED must light up; otherwise replace oil pressure switch.

- Continue increasing speed. At 2000 rpm and 80 °C oil temperature, oil overpressure must be at least 2.0 bar.

At higher speed, oil overpressure must not exceed 7.0 bar.

Tightening torques

  • Oil pressure switch tightening torque
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Removing and installing oil filter housing

Required special tools, testers and equipment, and auxiliary items

  • Oil filter wrench -3417-

Removing

- Drain engine oil.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Remove oil filter -arrow- with oil filter wrench -3417-.

Installing

- Fill oil filter with engine oil and install with oil filter wrench -3417- to specified tightening torque.

- Top up engine oil.

Engine oil capacity → "Capacities and specifications"

Oil filter tightening torque

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)