3-cyl. injection engine, timing belt drive (4-valve)

Oil pan/oil pump

20steps
~120min
4/5difficulty
0102030405097N·mlb·ft
Tightening torque found on this page
Done 0 of 20

Assembly overview - oil pan/oil pump

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  1. Oil dipstick
    • Oil capacities.
    • Check engine oil level min. and max. marks.
  2. Camshaft housing
  3. Filler Cap
    • Replace seal if damaged
  4. Check valve
  5. Sealing ring
    • Replace if damaged
  6. Oil separator
    • To remove, the intake manifold must be removed. "Removing and installing intake manifold"
    • Install with sealant D 176 501 A1
  7. Bolt
    • 9 N·m
  8. Oil pressure switch -F1-
    • for measuring range 0.3 ... 0.6 bar
    • Checking oil pressure switch. "Checking oil pressure and oil pressure switch"
    • Tightening torque: 20 N·m


Note

  • The oil pressure switch is sealed with a captive seal ring.
  • The seal ring is not suitable for repeated use; the oil pressure switch must be replaced after removal.
  1. Connector
  2. Oil filter
    • Observe installation notes on oil filter
    • Removing and installing with oil filter wrench -3417-
    • If the threaded socket for the oil filter has come loose in the oil pan
    • Tightening torque: 20 N·m
  3. Oil pan
    • Removing and installing. "Removing and installing oil pan"
    • Secure the loosened threaded socket for the oil filter
    • Clean sealing surface before installation
    • Install with silicone sealant D 176 501 A1
  4. Bolt
    • replace after removal
    • 8 N·m +90º
  5. Suction pipe
    • with integrated seal
  6. Bolt
    • 8 N·m
  7. Sealing ring
    • Replace if damaged
    • Removing and installing "Replacing seal ring for crankshaft, pulley side"
  8. Bolt
    • 20 N·m
  9. Sealing ring
    • replace after removal


Note

New procedure for all further service events

  1. Oil drain plug


Note

Replace only at the first oil change after factory installation.

  • 30 N·m
  1. Oil pump
    • only replace as a complete unit
    • Remove and install "Removing and installing oil pump"
  2. Bolt
    • replace after removal
    • 8 N·m +90º
  3. Gasket
    • replace after removal

Securing threaded stub for oil filter

  • If threaded stub -2- has come loose from oil pan -1-, secure it again as described below.

Carry out this procedure using only the two nuts -3 and 4-

  • 2 x hex nut -068 115 723- → Electronic parts catalog

- Screw nuts -3- and -4- onto threaded stub -2- and tighten them against each other (lock).

- Tighten threaded stub -2- by tightening nut -3-.

- Loosen both nuts and unscrew them, making sure the threaded stub does not come loose.

Tightening torques

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)


Oil drain plug with captive sealing washer (factory fitted)

- At the first oil change, discard the oil drain plug with captive sealing washer -1-.

- Fit the new oil drain plug -3- with replaceable sealing washer -2-.

Oil drain plug with replaceable sealing washer (all subsequent oil changes)

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew oil drain plug -2- and discard the used sealing washer -3-.

- The new sealing washer -1- can be replaced individually at subsequent oil changes.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Engine oil

Risk of catalytic converter damage. The oil level must not exceed the "Max." mark.

Fill quantities and specifications.

Check engine oil level.

Removing and installing oil pan

Required Special Tools, Test and Measuring Equipment and Auxiliary Items

  • Oil filter wrench -3417-
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  • Socket insert -T10058-
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

  • Torque Wrench -V.A.G 1331-
  • Hand drill with plastic brush attachment
  • Flat scraper
  • Silicone sealant D 176 501 A1

Removing

- Drain engine oil.

- Remove oil filter using oil filter wrench -3417-.

Only vehicles with air conditioning


Note

  • The air conditioning lines are not opened.
  • To avoid damage to the condenser and to the refrigerant lines and hoses.
  • Do not overstretch, kink or bend lines and hoses.

Remove and install ribbed belt "Removing and installing ribbed belt".

- Remove A/C compressor: → Heating, air conditioning.

- Secure A/C compressor to the lock carrier.

Do not kink the lines.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew transmission mounting bolts -arrows-.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew all oil pan mounting bolts -arrows-.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew the mounting bolts on the transmission side -arrows- using socket insert -T10058-.


Note

  • The oil pan is sealed with a liquid sealant.
  • When cured, the sealant has high adhesive strength.
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Carefully pry the oil pan off the cylinder block at the recess -arrow- using an installation lever.

- Remove oil pan. If necessary, loosen the oil pan by tapping lightly with a rubber mallet.

- Remove sealant residue from the cylinder block using a flat scraper.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Remove sealant residue from the oil pan using a rotating brush, e.g. a hand drill with plastic brush attachment (wear safety goggles).

- Clean the sealing surfaces. They must be free of oil and grease.

Installing


Note

  • Observe the sealant's shelf life.
  • The oil pan must be installed within 5 minutes after applying the silicone sealant.
  • The oil pan can be positioned more easily and accurately if M6 threaded pins are screwed into the cylinder block flange at 2 points as guides.
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Cut the tube nozzle at the front mark (nozzle diameter approx. 3 mm).

- Apply silicone sealant as shown to the clean sealing surface of the oil pan.

The sealant bead must:

be 2 ... 3 mm thick

Run past the inside of the bolt holes -arrows-


Note

The sealant bead must not be thicker, otherwise excess sealant may enter the oil pan and clog the strainer in the oil pickup tube.

- Install oil pan immediately and tighten all oil pan bolts lightly.

- Tighten new oil pan bolts.

Transmission bolt tightening torque:


Note

After installing the oil pan, the sealant must cure for approx. 30 minutes. Only then may engine oil be filled.

- Fill oil filter with engine oil and tighten using oil filter wrench -3417-.

- Top up engine oil.

Engine oil fill quantity "Engine oil".

- Install A/C compressor: → Heating, Air Conditioning.

Install ribbed belt (only for vehicles with air conditioning). "Removing and installing ribbed belt"

Reassembly is carried out in the reverse order of removal.

Tightening torques

  • Transmission bolt tightening torque
  • "Assembly overview - Oil pan/oil pump"
VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Removing and installing oil pump

Removing

- Disconnect battery → Electrical system.

- Remove alternator → Electrical System.

- Remove timing belt, see "Removing and installing timing belt".

- Remove oil pan, see "Removing and installing oil pan".

- Remove crankshaft seal, pulley side "Replacing crankshaft seal, pulley side".

- Unscrew mounting bolts -arrows- and remove tensioner element.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Unscrew oil pump mounting bolts -1- and -2-.

- Pull oil pump straight off the locating pins on the cylinder block.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Remove gasket -1- from the locating pins -arrows-.

Installing

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Place new gasket -1- onto the locating pins -arrows-.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Turn oil pump gear so that 2 opposite recesses -arrows- are vertical.

- Slide oil pump onto the locating pins.

- Tighten new mounting bolts -1- further by the specified torque angle.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Tighten mounting bolts -2- to the specified torque.

- Install new crankshaft seal, pulley side.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

- Fit tensioner element with new mounting bolts -arrows- and tighten to the specified torque.

- Install oil pan "Removing and installing oil pan".

- Install timing belt, see "Removing and installing timing belt".

- Install alternator → Electrical System.

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)

Tightening torques

VW UP. 3-Zyl. Einspritzmotor, Zahnriemenantrieb (4-Ventiler)