Vehicle-specific paint information

Seam sealing

~7min read

Seam sealing of body front


Note

  • During repair, restore the seam sealing to match the original appearance and layer thickness.
  • To avoid damage and malfunctions, sealing seams in the area of assembly-dependent attachments must be smoothed flat.
  • Water drain holes must remain open.
  • All threaded studs and weld nuts with M thread, as well as all other studs and mating surfaces for assembly, must remain functional after the sealing is applied.
  • The sealing material must not be applied to bare metal, only to filler-coated surfaces.

Seam sealing bulkhead

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Coarse seam sealing

  • For coarse seam sealing, the sealant must protrude by a total of 8 mm and have a height of 2 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing front left wheel housing shell

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Coarse seam sealing

  • For coarse seam sealing, the sealant must protrude by a total of 8 mm and have a height of 2 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing inner sill, A-pillar reinforcement

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing bonnet

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing of body centre


Note

  • During repair, restore the seam sealing to match the original appearance and layer thickness.
  • To avoid damage and malfunctions, sealing seams in the area of assembly-dependent attachments must be smoothed flat.
  • Water drain holes must remain open.
  • All threaded studs and weld nuts with M thread, as well as all other studs and mating surfaces for assembly, must remain functional after the sealing is applied.
  • The sealing material must not be applied to bare metal, only to filler-coated surfaces.

Seam sealing roof

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing roof with panoramic sliding roof

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing door, 2-door

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.

- Sealing the hem flange loop

  • After applying sealant to a hem flange loop, close the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal so the hem flange loop remains closed.

Seam sealing front door, 4-door

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.

- Sealing the hem flange loop

  • After applying sealant to a hem flange loop, close the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal so the hem flange loop remains closed.

Seam sealing rear door, 4-door

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.

- Sealing the hem flange loop

  • After applying sealant to a hem flange loop, close the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal so the hem flange loop remains closed.

Seam sealing rear door outer, 4-door

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing of body rear


Note

  • During repair, restore the seam sealing to match the original appearance and layer thickness.
  • To avoid damage and malfunctions, sealing seams in the area of assembly-dependent attachments must be smoothed flat.
  • Water drain holes must remain open.
  • All threaded studs and weld nuts with M thread, as well as all other studs and mating surfaces for assembly, must remain functional after the sealing is applied.
  • The sealing material must not be applied to bare metal, only to filler-coated surfaces.

Seam sealing C-pillar

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing rear wheel housing

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Coarse seam sealing

  • For coarse seam sealing, the sealant must protrude by a total of 8 mm and have a height of 2 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.

Seam sealing tailgate

Left side shown, right side mirrored

VW UP. Fahrzeugspezifische Informationen Lack

- Fine seam sealing

  • For fine seam sealing, the sealant must protrude by at least 3 mm and have a height of 0.5 mm.

- Smoothing the seal

  • After applying the sealant, smooth the marked areas.


Note

When smoothing the seam sealing, make sure the sheet metal edges to be protected are not exposed. A sufficiently thick PVC layer must cover the sheet metal.