Brake system

Sensors

25steps
~150min
4/5difficulty
0102030405086N·mlb·ft
Tightening torque found on this page
Done 0 of 25

Remove and install yaw rate sensor and lateral acceleration sensor

In this vehicle, the lateral acceleration sensor -G200-, the yaw rate sensor -G202- and the longitudinal acceleration sensor -G251- (depending on equipment) are installed in the control module.

Separate replacement is not possible.

- Remove and install control module for ABS -J104-.

Remove and install steering angle sensor

The steering angle sensor -G85- is installed between the steering wheel and the steering column switch.

Removing and installing:

→ Electrical System.

- Then perform a basic setting of the steering angle sensor -G85-.

- Connect the -vehicle diagnostic tester- and select the function.

Removing and installing speed sensor on rear axle

Removing:

- Raise the vehicle.

- Disconnect connector -1- from the speed sensor wire and the speed sensor.

- Unscrew bolt -2- from the stub axle.

- Pull the ABS speed sensor out of the stub axle.

Installing:

- Before installing the speed sensor, clean the inside surface of the bore and coat the speed sensor all round with high-temperature grease paste G 052 112 A3.

- Insert the speed sensor into the bore of the stub axle and tighten the bolt to 8 N·m.

- Connect the speed sensor to the speed sensor wire.

VW UP. Bremsanlagen

Exploded view - speed sensor on rear axle

VW UP. Bremsanlagen

  1. Axle beam
  2. Torx bolt, 8 N·m
  3. ABS speed sensor
    • Before installing the sensor, clean the inside surface of the bore and coat it with high-temperature grease paste G 052 112 A3.
    • Remove and install
  4. Brake line
  5. Stub axle
  6. Brake cable
  7. Hex bolt
    • Tightening torque → Suspension, Axles, Steering
  8. Torx bolt, 8 N·m
  9. Brake drum
    • Retract the brake before removing the brake drum.
  10. Cap
    • Press off and drive in → Suspension, Axles, Steering
  11. 12-point nut, self-locking
    • Replace after every removal → Suspension, Axles, Steering
  12. Wheel hub with wheel bearing
    • The ABS sensor ring is installed in the wheel bearing.
    • Remove and install → Suspension, Axles, Steering
  13. Brake backing plate with brake shoes
    • Before removing the brake drum, retract the brake.

ABS sensor ring -1-

VW UP. Bremsanlagen

Removing and installing speed sensor on front axle

Removing:

- Raise the vehicle.

- Disconnect connector -1- from the speed sensor wire and the speed sensor.

- Unscrew bolt -2- from the wheel bearing housing.

- Pull the ABS speed sensor out of the wheel bearing housing.

Installing:

- Before installing the speed sensor, clean the inside surface of the bore and coat the speed sensor all round with high-temperature grease paste G 052 112 A3.

- Insert the speed sensor into the bore of the wheel bearing housing and tighten the bolt to 8 N·m.

- Connect the speed sensor to the speed sensor wire.

- Turn the steering fully left and right to the stop and check that the speed sensor wire moves freely.

VW UP. Bremsanlagen

Exploded view - speed sensor on front axle

VW UP. Bremsanlagen

  1. Driveshaft
  2. Wheel bearing housing
  3. Torx bolt, 8 N·m
  4. Speed sensor
    • Before installing the sensor, clean the inside surface of the bore and coat it with high-temperature grease paste G 052 112 A3.
    • Remove and install
  5. Brake disc
  6. Wheel hub
  7. Circlip
  8. Wheel bearing
    • The ABS sensor ring is installed in the wheel bearing.
    • Press out and press in → Suspension, Axles, Steering
  9. Torx bolts, 12 N·m
  10. Cover plate
  11. Torx bolt, 4.5 N·m
  12. 12-point nut, self-locking

ABS sensor ring -1-

VW UP. Bremsanlagen