Hyundai Genesis DH Quiz
Body Electrical System

Power Window Switch Repair Procedures

In this manual: Body Electrical System
General Information — 9Engine Mechanical System — 103Engine Electrical System — 54Emission Control System — 23Engine Control System/Fuel System — 127Automatic Transmission System (SBC) — 90All-Wheel Drive (AWD) System — 20Drive Shaft and Axle — 27Suspension System — 41Steering — 19Restraints — 56Brake System — 56Body (Interior and Exterior) — 211Body Electrical System — 279Heating, Ventilation, and Air Conditioning — 55
24steps
~144min
4/5difficulty
Done 0 of 24

Inspection

Diagnosis Using GDS
  1. In the electrical system, malfunctions can be quickly diagnosed using the Global Diagnostic System (GDS).
    1. Self-Diagnosis: Checks malfunction and Diagnostic Trouble Code (DTC)
    2. Current Data: Check the system input/output status.
    3. Actuation Test: Check the system operating status
    4. Additional Functions: Controls other functions, including system parameter setting and zero point adjustment.
  2. Select "Vehicle Model" and the system to be checked to inspect the vehicle with the tester.
  3. Select "Driver Seat or Assist Seat Door Module (DDM/ADM)" to check the driver seat or assist seat door module (DDM/ADM).
  4. Select the "Current Data" menu to check the current input/output status. The input/output data for the sensors related to the driver seat or assist door module (DDM/ADM) can be checked.
  5. If you force-check the power door lock operation, select "Activation Check".

Removal

Driver Window Switch
  • Wrap the screwdriver or puller tool with protective tape.
  • Handle with care during storage and during disassembly/assembly, as it is easily contaminated by grease and oil.
  • Be careful not to scratch or break the trim panel and the upper part of the door trim, as well as the wood grain (real wood) garnish.
  • Be careful not to scratch the door trim and other parts.
  1. Disconnect the negative (-) battery terminal.
  2. Remove the front door trim panel.
  3. Disconnect the DDM (Driver Door Module) connector (A) from the wiring harness.
  4. If the trim panel interferes with removal, remove the trim panel (A) after loosening the mounting screws.
  5. Remove the DDM (Driver Door Module) (A) after loosening the mounting screws.
Auxiliary Power Window Switches
  • Wrap the screwdriver or puller tool with protective tape.
  • Handle with care during storage and during disassembly/assembly, as it is easily contaminated by grease and oil.
  • Be careful not to scratch or break the trim panel and the upper part of the door trim, as well as the wood grain (real wood) garnish.
  • Be careful not to scratch the door trim and other parts.
  1. Disconnect the negative (-) battery terminal.
  2. Remove the front door trim panel.
  3. Disconnect the ADM (Auxiliary Door Module) connector (A) from the wiring harness.
  4. Remove the obstacle cover (A) after loosening the mounting screws.
  5. Remove the ADM (Auxiliary Door Module) (A) after loosening the mounting screws.
  6. Disconnect the negative (-) battery terminal.
  7. Remove the rear door trim panel. (Refer to Body - "Rear Door Trim")
  8. Remove the power window switch assembly (A) after loosening the mounting screws.
Rear Power Window Switch

Installation

Driver Window Switch
  1. Install the power window switch assembly.
  2. Install the front door trim panel after connecting the connector.
  3. Install the power window switch assembly.
  4. Install the front door trim panel after connecting the connector.
  5. Install the power window switch assembly.
  6. Install the rear door trim panel after connecting the connector.
Auxiliary Power Window Switch Rear Power Window Switch

Test yourself

A quick Hyundai Genesis DH quiz: every answer comes with an explanation and a link to the manual page.