Suspension

Front Lower Link

~9min read

Exploded View

Frame Stopper rubber Axle housing
Front lower link Eccentric disc Adjusting bolt
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)

Removal and Installation

REMOVAL

Without Dynamic Digital Suspension and Electronic Air Suspension

Remove tires. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove wheel sensor and harness connector. Move wheel sensor in a place where it will not interfere with work. Refer to Removal and Installation.

Set suitable jack under rear lower link.

Remove brake caliper assembly. Hang brake caliper assembly in a place where it will not interfere with work. Refer to Removal and Installation.

Loosen rear lower link mounting nuts (frame side).

Separate rear lower link from axle housing. Refer to Removal and Installation.

Lower suitable jack, and remove coil spring. Refer to Removal and Installation.

Set suitable jack under front lower link.

Separate front lower link from axle housing. Refer to Removal and Installation.

Remove shock absorber mounting bolts from front lower link. Refer to Removal and Installation.

Remove stabilizer connecting rods from front lower link. Refer to Removal and Installation.

Remove front lower link mounting bolt, nuts, stopper rubbers, eccentric disc, and adjusting bolt from frame, and remove front lower link.

Perform inspection after removal. Refer to Inspection.

With Dynamic Digital Suspension and Electronic Air Suspension

Start engine.

Turn Auto height mode control switch to ON, shift the shift position to N and set to normal height.

Turn OFF the electronic air suspension function. Refer to Operation.

Stop engine.

Lift up the vehicle.

Remove rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove wheel sensor and harness connector. Move wheel sensor in a place where it will not interfere with work. Refer to Removal and Installation.

Disconnect shock absorber harness connector.

Support the rear lower link with suitable jack (A) until most horizontal angle with vehicle on the ground.

Loosen the air connector and perform air bleeding.

Remove air tube together with air connector from air spring .

Remove brake caliper assembly. Hang brake caliper assembly in a place where it will not interfere with work. Refer to Removal and Installation.

Loosen rear lower link mounting nuts (frame side).

Separate rear lower link from axle housing. Refer to Removal and Installation.

Set suitable jack under front lower link.

Separate front lower link from axle housing. Refer to Removal and Installation.

Remove shock absorber mounting bolts from front lower link. Refer to Removal and Installation.

Remove stabilizer connecting rods from front lower link. Refer to Removal and Installation.

Remove front lower link mounting bolt, nuts, stopper rubbers, eccentric disc, and adjusting bolt from frame, and remove front lower link.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Without Dynamic Digital Suspension and Electronic Air Suspension

Note the following, and install in the reverse order of removal.

  • Perform final tighting of front lower link (frame side) by the following procedures.

    1. Measure between wheel center and fender arch (A).

    2. Set the wheel chocks on the front tires.

    3. Jack up the rear of the vehicle and set the rigid rack.

    4. Remove the rear tires.

    5. Set suitable jacks (A) on the left and right axle housings . (axle housing ball joint fastening part).

    6. Jack up the left and right axle housings until the vehicle no longer floats off the rigid rack (A).

    7. Measure between wheel center and fender arch (A).

    8. Tight the mounting nuts of front lower link (frame side) to the specified torque. Refer to Exploded View.

  • Perform inspection after installation. Refer to Inspection.

With Dynamic Digital Suspension and Electronic Air Suspension

Install front lower link mounting bolt, nuts, stopper rubbers, eccentric disc, and adjusting bolt to frame, and install front lower link.

Install shock absorber to front lower link. Refer to Removal and Installation.

Install stabilizer connecting rods to front lower link. Refer to Removal and Installation.

Install front lower link to axle housing. Refer to Removal and Installation.

Install rear lower link to axle housing. Refer to Removal and Installation.

Tighten rear lower link mounting nuts (frame side). Refer to Removal and Installation.

Install brake caliper assembly. Refer to Removal and Installation.

Install air tube and air connector together to air spring .

Start engine.

Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.

Remove suitable jack from rear lower link.

Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.

Install shock absorber harness connector.

Stop engine.

Install rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Lift down the vehicle.

Start engine.

Perform pressure measurements using CONSULT. Refer to Work Support.

Perform the height sensor calibration using CONSULT. Refer to Work Support.

Use CONSULT and vehicle to the normal height. Refer to Work Support.

Turn ON the electronic air suspension function. Refer to Operation.

Stop engine.

Perform final tighting of front lower link (frame side) by the following procedures.Measure between wheel center and fender arch (A).

Set the wheel chocks on the front tires. Jack up the rear of the vehicle and set the rigid rack. Remove rear tires. Set suitable jacks (A) on the left and right axle housings . (axle housing ball joint fastening part).
Jack up the left and right axle housings until the vehicle no longer floats off the rigid rack (A).
Measure between wheel center and fender arch (A).
Tight the mounting nuts of front lower link (frame side) to the specified torque. Refer to Exploded View. Install rear tires.

Perform inspection after installation. Refer to Inspection.

Inspection

INSPECTION AFTER REMOVAL

Appearance

Check the following items, and replace the part if necessary.

  • Front lower link and bushing for deformation, cracks or damage.

  • Boot of ball joint for cracks or damage, and also for grease leakage.

Ball Joint Inspection

Manually move ball stud to confirm it moves smoothly with no binding.

Swing Torque Inspection

Move the ball joint at least ten times by hand to check for smooth movement.

Hook spring balance (A) at groove. Confirm spring balance measurement value is within specifications when ball stud begins moving.

Swing torque : Refer to Ball Joint.
  • If swing torque exceeds the standard range, replace front lower link.

Rotating Torque Inspection

Move the ball joint at least ten times by hand to check for smooth movement.

Attach mounting nut to ball stud. Check that rotating torque is within specifications with a preload gauge [SST: ST3127S000 (NI-25765-A)] (A).

Rotating torque : Refer to Ball Joint.
  • If rotating torque exceeds the standard range, replace front lower link.

Axial End Play Inspection

Move the ball joint at least ten times by hand to check for smooth movement.

Move tip of ball stud in axial direction to check for looseness.

Axial end play : Refer to Ball Joint.
  • If axial end play exceeds the standard range, replace front lower link.

INSPECTION AFTER INSTALLATION

Without Dynamic Digital Suspension and Electronic Air Suspension

Check wheel alignment. Refer to Inspection.

With Dynamic Digital Suspension and Electronic Air Suspension

  • Make sure the electronic air suspension function is turn ON. Refer to Operation.

  • Confirm that no warning message is displayed on the information display. Refer to Air suspension warning.

  • Perform the self-diagnosis with CONSULT. Check if any DTC is detected. Refer to CONSULT Function.

  • Confirm to close the hood.

  • Always check for the air leakage with soapy water.

  • Check wheel alignment. Refer to Inspection.