Suspension

Rear Lower Link and Air Spring

~8min read

Exploded View

Frame Upper spring seat Air spring
Adjusting bolt Eccentric disc Rear lower link
Axle housing Lower spring seat Air suspension duct assembly
Air suspension LH duct assembly Air suspension RH duct assembly Bracket
Air connector Air tube
Left side Right side To air suspension control module
: Always replace after every disassembly.
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)

Removal and Installation

REMOVAL

Start engine.

Turn auto height mode control switch to ON, shift the shift position to N and set to normal height.

Turn OFF the electronic air suspension function. Refer to Operation.

Stop engine.

Lift up the vehicle.

Remove rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Remove wheel sensor and harness connector. Move wheel sensor in a place where it will not interfere with work. Refer to Removal and Installation.

Support the rear lower link with suitable jack (A) until most horizontal angle with vehicle on the ground.

Apply the matching marks to the air tube when replacing air connector .

Loosen the air connector and perform air bleeding.

When reusing the air connector , remove air tube and air connector together to air spring .

When replacing the air connector, follow the procedure below.Slide the air connector part to direction , and remove the part from the air tube .

Remove the air connector part from the air tube .

Loosen clamp , and separat air suspension duct assembly from duct part of air spring .

Remove rear height sensor. Refer to Removal and Installation.

Loosen rear lower link mounting nuts (frame side).

Separate rear lower link from axle housing.

Remove air spring from upper spring seat, follow the procedure below.Turn the air spring in the direction of the arrow () so that the notch of the upper spring seat and the air connector hole are in the same direction.

Separate the air spring from the upper spring seat in direction .

Lower suitable jack, and remove air spring from rear lower link.

Remove lower spring seat from air spring.

Remove upper spring seat mounting bolts, and remove upper spring seat.

Remove rear lower link mounting nut, eccentric disc, and adjusting bolt from frame, and remove rear lower link.

Remove air suspension LH/RH duct assembly, air suspension duct assembly, and brckets if necessary.

Perform inspection after removal. Refer to Inspection.

INSTALLATION

Install air suspension LH/RH duct assembly, air suspension duct assembly, and brckets if necessary.

Install rear lower link, rear lower link mounting nut, eccentric disc, and adjusting bolt to frame.

Install upper spring seat.

Install lower spring seat to air spring , align the angles of the elongated hole of the lower spring seat and the elongated hole of the air spring.

Install air spring to upper spring seat, follow the procedure below.Using the notch of the upper spring seat as a guide, insert the pin part of the air spring into the hole of the upper spring seat.

Turn the air spring in the direction of the arrow (), and install it so that the protrusion on the upper spring seat and the air connector hole are in the same direction.

Set suitable jack under rear lower link, and jack up until air spring seats to the lower link without damaging the air spring.

Install rear lower link to axle housing.

Tighten rear lower link mounting nuts (frame side).

Install rear height sensor. Refer to Removal and Installation.

Apply soapy water to the duct part of air spring.

Install air suspension duct assembly to duct part of air spring , and tighten clamp .

When reusing the air connector, install air tube and air connector together to air spring .

When replaced the air connector, follow the procedure below.Install air connector to air spring Insert the air tube straight into the air connector to the marked point which is applied when removing.

Start engine.

Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer Work Support.

Remove suitable jack from rear lower link.

Use CONSULT and fill the inner pressure of air spring to 3.3 bar. Refer to Work Support.

Stop engine.

Install rear tire. Refer to ROAD WHEEL TIRE : Removal & Installation.

Lift down the vehicle.

Start engine.

Perform pressure measurements using CONSULT. Refer to Work Support.

Perform the height sensor calibration using CONSULT. Refer to Work Support.

Use CONSULT and vehicle to the normal height. Refer to Work Support.

Turn ON the electronic air suspension function. Refer to Operation.

stop engine.

Perform final tighting of rear lower link by the following procedures.Measure between wheel center and fender arch (A).

Set the wheel chocks on the front tires. Jack up the rear of the vehicle and set the rigid rack. Remove rear tires. Set suitable jacks (A) on the left and right axle housings . (axle housing ball joint fastening part).
Jack up the left and right axle housings until the vehicle no longer floats off the rigid rack (A).
Measure between wheel center and fender arch (A).
Tight the mounting nuts of rear lower link to the specified torque. Refer to Exploded View. Install rear tires.

Perform inspection after installation. Refer to Inspection.

Inspection

INSPECTION AFTER REMOVAL

Check rear lower link, bushing and air spring for deformation, crack, and damage. Replace it if necessary.

INSPECTION AFTER INSTALLATION

  • Make sure the electronic air suspension function is turn ON. Refer to Operation.

  • Confirm that no warning message is displayed on the information display. Refer to Air suspension warning.

  • Perform the self-diagnosis with CONSULT. Check if any DTC is detected. Refer to CONSULT Function.

  • Confirm to close the hood.

  • Always check for the air leakage with soapy water.

  • Check wheel alignment. Refer to Inspection.