Transaxle & transmission CVT: RE0F10B

Additional service when replacing transaxle assembly

In this manual: Transaxle & transmission CVT: RE0F10B
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~3min read

Description

Perform the following work after the transaxle assembly is replaced.

CHECK LOADING OF CALIBRATION DATA

• The TCM acquires calibration data (individual characteristic value) of each solenoid that is stored in the ROM assembly (in the control valve). This enables the TCM to perform accurate control. After the TCM is replaced, check that the TCM has correctly loaded the calibration data.

G sensor calibration
• TCM stores calibration data (inherent characteristic value) of G sensor to provide accurate control. Therefore, it is required to perform calibration of G sensor after the following work is performed.

Idle neutral control
• TCM corrects an individual difference in clutch clearance of the transaxle assembly by performing the idle neutral control learning and enables accurate idle neutral control.

• Therefore, it is required to perform idle neutral control learning after replacement or TCM.

CAUTION:
• When replacing TCM and transaxle assembly as a set, replace transaxle assembly first and then replace TCM.

• If the TCM is replaced in advance, perform the following items.

1. ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRANSAXLE ASSEMBLY 2. CALIBRATION OF G SENSOR 3. IDLE NEUTRAL CONTROL LEARNING

Procedure

CAUTION:
Immediately after TCM is replaced or after control valve or transaxle assembly is replaced (after TCM initialization is complete), self-diagnosis result of “P1701” may be displayed. In this case, erase selfdiagnosis result using CONSULT-III. After erasing self-diagnosis result, perform DTC P1701 reproduction procedure and check that malfunction is not detected. Refer to TM-239, "DTC Logic".
1.PREPARATION BEFORE WORK

1. Start the engine.With CONSULT-III


1. Start the engine.

CAUTION:
Never drive the vehicle.
2. Select “Data monitor” in “TRANSMISSION”.

3. Select “ATFTEMP COUNT”.

Is “ATFTEMP COUNT” 47 [equivalent to 20 °C] or more? YES >> GO TO 2.

NO >> 1. Warm up the transaxle assembly until “ATFTEMP COUNT” reaches “47” [equivalent to 20 °C] or more.

2. GO TO 2.

2.PERFORM TCM INITIALIZATION

With CONSULT-III

1. Turn ignition switch OFF.

2. Turn ignition switch ON.

CAUTION:
Never start the engine.
3. Select “Self Diagnostic Results” in “TRANSMISSION”. 4. Shift selector lever to “R” position. 5. Depress slightly the accelerator pedal (Pedal angle: 2.0/8) while depressing the brake pedal. 6. Select “Erase” with step 5. 7. Release brake pedal and accelerator pedal. 8. Turn ignition switch OFF while keeping the selector lever in “R” position. 9. Wait approximately 10 seconds. 10. Turn ignition switch ON while keeping the selector lever in “R” position. 11. Select “Special function” in “TRANSMISSION”. 12. Select “CALIB DATA”.

13. Check that “CALIB DATA” value is as shown as in the following table.

Is “CALIB DATA” value it?

Is “CALIB DATA” value it? YES >> GO TO 3.

NO >> GO TO 1.

3.CHECK AFTER WORK 1. Shift selector lever to “P” position.

2. Check that “P” is displayed on shift position indicator on combination meter.

NOTE

:
It indicates approximately 1 or 2 seconds after shifting the selector lever to “P” position.

Does shift position indicator display “P”? YES >> GO TO 5.

NO >> GO TO 4.

4.DETECTION OF MALFUNCTION ITEMS Check the following items: • Harness between the TCM and the ROM assembly inside the transaxle assembly is open or shorted.

• Disconnected, loose, bent, collapsed, or otherwise abnormal connector housing terminals
• Power supply and ground of TCM. (Refer to TM-239, "Diagnosis Procedure".) Is the inspection result normal? YES >> GO TO 1.

NO >> Repair or replace the malfunctioning parts.

5.PERFORM G SENSOR CALIBRATION

Refer to TM-182, "Procedure".

>> GO TO 6.

6.PERFORM IDLE NEUTRAL CONTROL LEARNING

Refer to TM-183, "Description".

>> WORK END