Transaxle & transmission CVT: RE0F10B

Road test

In this manual: Transaxle & transmission CVT: RE0F10B
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~5min read

Description

DESCRIPTION

• The purpose of the test is to determine overall performance of CVT and analyze causes of problems.

• The road test consists of the following three parts:

1. “Check Before Engine Is Started” TM-190. 2. “Check at Idle” TM-191.

3. “Cruise Test” TM-192.

• Before road test, familiarize yourself with all test procedures and

• Before road test, familiarize yourself with all test procedures and items to check.

• Perform tests on all items until specified symptom is found. Troubleshoot items the malfunctioning items after road test.

CONSULT-III SETTING PROCEDURE

CONSULT-III SETTING PROCEDURE

• Using CONSULT-III, perform a cruise test and record the result.

• Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.

1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen. 2. Touch “MAIN SIGNALS” to set recording condition. 3. See “Numerical Display”, “Barchart Display” or “Line Graph Display”. 4. Touch “START”. 5. When performing cruise test. Refer to TM-192, "Cruise Test". 6. After finishing cruise test part, touch “RECORD”. 7. Touch “STORE”. 8. Touch “BACK”. 9. Touch “DISPLAY”. 10. Touch “PRINT”.

11. Check the monitor data printed out.

Check before Engine Is Started

1.CHECK CVT INDICATOR LAMP 1. Park vehicle on flat surface. 2. Move selector lever to “P” position. 3. Turn ignition switch OFF. Wait at least 5 seconds.

4. Turn ignition switch ON. (Do not start engine.)

Is shift position indicator activated for about 2 seconds? YES >> 1. Turn ignition switch OFF.

2. Perform self-diagnosis and note NG items.

Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

3. Go to TM-191, "Check at Idle".

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

Check at Idle

1.CHECK STARTING THE ENGINE 1. Park vehicle on flat surface. 2. Move selector lever to “P” or “N” position. 3. Turn ignition switch OFF.

4. Turn ignition switch to “START” position.

Is engine started? YES >> GO TO 2.

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

2.CHECK STARTING THE ENGINE 1. Turn ignition switch ON. 2. Move selector lever to “D”, “M” or “R” position.

3. Turn ignition switch to “START” position.

Is engine started? YES >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

NO >> GO TO 3.

3.CHECK “P” POSITION FUNCTION 1. Move selector lever to “P” position. 2. Turn ignition switch OFF. 3. Release parking brake. 4. Push vehicle forward or backward.

5. Apply parking brake.

Does vehicle move forward or backward? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 4.

4.CHECK “N” POSITION FUNCTION 1. Start engine. 2. Move selector lever to “N” position.

3. Release parking brake.

Does vehicle move forward or backward? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 5.

5.CHECK SHIFT SHOCK 1. Apply foot brake.

2. Move selector lever to “R” position.

Is there large shock when changing from “N” to “R” position? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 6.

6.CHECK “R” POSITION FUNCTION

Release foot brake for several seconds.

Does vehicle creep backward when foot brake is released? YES >> GO TO 7.

NO >> Refer toTM-259, "Symptom Table". Continue “Road Test”.

7.CHECK “D” POSITION FUNCTION

Move selector lever to “D” position and check if vehicle creeps forward.

Does vehicle creep forward in all positions? YES >> Go to TM-192, "Cruise Test".

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

Cruise Test

1.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 1

1. Drive vehicle for approximately 10 minutes to warm engine oil and CVT fluid up to operating temperature.

CVT fluid operating temperature: 50 – 80 °C

2. Park vehicle on flat surface. 3. Move selector lever to “P” position. 4. Start engine. 5. Move selector lever to “D” position.

6. Accelerate vehicle to 2/8-way throttle depressing accelerator pedal constantly.

speed. Refer to TM-308,Read vehicle speed and engine
speed. Refer to TM-308, "Shift Characteristics".

OK or NG

OK >> GO TO 2.

NG >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

2.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 2

2.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 2 1. Park vehicle on flat surface. 2. Move selector lever to “D” position.

3. Accelerate vehicle to full depression depressing accelerator pedal constantly.

speed.Refer to TM-308,Read vehicle speed and engine
speed.Refer to TM-308, "Shift Characteristics".

OK or NG

OK >> GO TO 3.

NG >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

3.CHECK MANUAL MODE FUNCTION

3.CHECK MANUAL MODE FUNCTION

Move to manual mode from “D” position.

Does it switch to manual mode? YES >> GO TO 4.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

4.CHECK SHIFT-UP FUNCTION

During manual mode driving, is upshift from M1 → M2 → M3 → M4 → M5 → M6 performed? TM-159, "CONSULT-III Function (TRANSMISSION)".Read the gear position. Refer to
TM-159, "CONSULT-III Function (TRANSMISSION)".

Is upshifting correctly performed? YES >> GO TO 5.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

5.CHECK SHIFT-DOWN FUNCTION

During manual mode driving, is downshift from M6 → M5 → M4 → M3 → M2 → M1 performed? TM-159, "CONSULT-III Function (TRANSMISSION)".Read the gear position. Refer to
TM-159, "CONSULT-III Function (TRANSMISSION)".

Is downshifting correctly performed? YES >> GO TO 6.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

6.CHECK ENGINE BRAKE FUNCTION

Check engine brake.

Does engine braking effectively reduce speed in M1 position? YES >> 1. Stop the vehicle.

2. Perform self-diagnosis. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

NO >> Refer to TM-259, "Symptom Table". Then continue trouble diagnosis.