Engine Mechanical MR16DDT

Fuel injector and fuel tube

In this manual: Engine Mechanical MR16DDT
Foreword — 1General information — 45Engine Mechanical MR16DDT — 61Engine Mechanical HR16DE — 52Engine Mechanical K9K — 46Engine Lubrication System MR16DDT — 18Engine Lubrication System HR16DE — 14Engine Lubrication System K9K — 11Engine Cooling System MR16DDT — 28Engine Cooling System HR16DE — 29Engine Cooling System K9K — 24Engine Control System MR16DDT — 163Engine Control System HR16DE — 115Engine Control System K9K — 129Fuel System MR16DDT — 13Fuel system HR16DE — 11Fuel system K9K — 12Exhaust system MR16DDT — 7Exhaust system HR16DE — 10Exhaust system K9K — 7Starting system — 24Accelerator control system — 6Clutch — 25Driveline transfer: TY21B — 77Driveline rear propeller Shaft: 3Fφ16-ETJ75 — 12Driveline rear final drive: RTVS — 31Transaxle & transmission 5MT: RS5F92R — 31Transaxle & transmission 6MT: RS6F94R — 30Transaxle & transmission CVT: RE0F10B — 93Transaxle & transmissioN CVT: RE0F11A — 103Front Axle MR16DDT — 18Front Axle HR16DE — 17Front Axle K9K — 17Rear Axle 2WD — 6Rear Axle 4WD — 13Front Suspension — 21Rear Suspension 2WD — 13Rear Suspension 4WD — 17Road Wheels & Tires — 6Brake System LHD — 24Brake System RHD — 24Parking Brake System — 8Brake Control System without ESP — 44Brake Control System with ESP — 63Steering System — 14Steering Control System — 27Seat Belt — 8SRS Airbag — 24SRS Airbag Control System — 93Ventilation System — 11Heater & Air Conditioning System HR16DE — 28Heater & Air Conditioning System MR16DDT — 28Heater & Air Conditioning Control System Type 1 — 49Heater & Air Conditioning Control System Type 2 — 51Heater & Air Conditioning Control System Type 3 — 32Heater & Air Conditioning Control System Type 4 — 40Heater & Air Conditioning Control System Type 5 — 21Interior — 16Instrument Panel — 10Seat — 18Door & Lock Type 1 — 83Door & Lock type 2 — 80Door & Lock type 3 — 65Door & Lock type 4 — 60Security Control System with intelligent key system — 82Security Control System without intelligent key system — 41Glass & Window System — 15Power Window Control System — 28Body Repair — 13Exterior — 20Mirrors — 26Exterior Lighting System Halogen type — 51Interior Lighting System — 24Wiper & Washer — 45Defogger — 31Horn — 4Power Outlet — 4Body Control System With intelligent key system — 21Body Control System Without intelligent key system — 23LAN system can fundamental — 6LAN system can — 31LAN System can system (type 1) — 1LAN System can system (type 2) — 1LAN System can system (type 3) — 1LAN System can system (type 4) — 1LAN System can system (type 5) — 1LAN System can system (type 6) — 1LAN System can system (type 7) — 2LAN System can system (type 8) — 1LAN System can system (type 9) — 1LAN System can system (type 10) — 1LAN System can system (type 11) — 1Power Control System IPDM E/R (with I-key) — 14Power Control System IPDM E/R (without I-key) — 14Power Control System Power distribution system — 25Charging System — 22Power Supply, Ground & Circuit Elements — 20Meter, Warning Lamp & Indicator — 33Warning Chime System — 22Audio, Visual & Navigation System Audio without navigation — 30Audio, Visual & Navigation System Audio with navigation — 33Audio, Visual & Navigation System NISSAN dynamic control system — 22Cruise Control System — 1Drive Mode System — 10Maintenance — 14
~7min read
01020304050107N·mlb·ft
Tightening torque found on this page

Exploded View

1. Holder

1. Holder
2. Seal ring (white)
3. Backup ring
4. O-ring (blue)
5. Fuel injector
6. Stud bolt
7. Fuel tube assembly
8. Fuel tube insulator
9. Fuel tube protector
10. Fuel pressure sensor 11. O-ring
12. Fuel tube adaptor
13. Backup ring (white) 14. Backup ring (brown) 15. O-ring (black)

A. To fuel tube
B. Tighting must be done following the installation procedure. Refer to EM-47

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
: Always replace after every: N·m (kg-m, in-lb)
disassembly.: Always replace after every
disassembly.

CAUTION:: Should be lubricated with oil.


CAUTION:
Never remove or disassemble parts unless instructed as shown in the figure.

Removal and Installation

WARNING:
• Be sure to read EM-7, "Precaution for Handling High Pressure Fuel System" when working on the high pressure fuel system. • Put a “CAUTION: FLAMMABLE” sign in the workshop. • Be sure to work in a well ventilated area and furnish workshop with a CO2 fire extinguisher. • Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.

• To avoid the danger of being scalded, never drain engine coolant when engine is hot.

REMOVAL

1. Release the fuel pressure. Refer to EC-140, "Work Procedure". 2. Remove front bumper. Refer to EXT-12, "Exploded View" 3. Remove charge are cooler. Refer to EM-31, "Exploded View". 4. Remove oil level gauge. Refer to EM-40, "Exploded View". 5. Remove intake manifold. Refer to EM-28, "Exploded View". 6. Remove alternator. Refer to CHG-30, "MR16DDT : Exploded View" 7. Remove oil level gauge guide. Refer to EM-40, "Exploded View". 8. Remove fuel tube protector, and them remove fuel tube insulator. 9. Remove high pressure pump insulator. Refer to EM-43, "Exploded View". 10. Remove fuel tube. Refer to EM-43, "Exploded View". 11. Disconnect fuel pressure sensor harness connector. 12. Disconnect fuel injector harness connector.

13. Remove fuel tube.

• Loosen mounting bolts in reverse order as shown in the figure.

CAUTION:: Engine front


CAUTION:
• When removing, be careful to avoid any interference with fuel injector.

• Use a shop cloth to absorb any fuel leakage from fuel tube.

14. Remove fuel pressure sensor and fuel tube adaptor, if necessary.

14. Remove fuel pressure sensor and fuel tube adaptor, if necessary.

15. Remove fuel injector from cylinder head as per the following.

CAUTION:
• Be careful with remaining fuel that may go out from fuel tube. • Be careful no to damage injector nozzles during removal. • Never bump or drop fuel injector.

• Never disassemble fuel injector.

a. Remove injector holder.

b. Install an remover [SST: KV10119600] (A) to the injector connector side so that cutout (B) of injector remover faces the injector connector side.

• Hook pawl portion (B) of injector remover [SST: KV10119600]

• Hook pawl portion (B) of injector remover [SST: KV10119600] (A) to groove portion (C) of injector

c. Press down body portion (A) of injector remover [SST:

c. Press down body portion (A) of injector remover [SST: KV10119600] until it contacts cylinder head.

d. Tighten injector remover [SST: KV10119600] clockwise and

d. Tighten injector remover [SST: KV10119600] clockwise and remove injector from cylinder head.

e. Cut teflon seal (1) while pinching it. Be careful not to damage

e. Cut teflon seal (1) while pinching it. Be careful not to damage injector.

f. Remove insulator from mounting hole of fuel injector of cylinder head.

INSTALLATION

INSTALLATION

1. Install seal ring to fuel injector as per the following: CAUTION:
• Handle seal ring with bare hands. Never wear gloves. • Never apply engine oil to seal ring.

• Never clean seal ring with solvent.

a. Install an injector seal drift set [SST: KV101197S0 (—)] (A) to fuel injector (1).

b. Set seal ring (1) to injector seal drift set [SST: KV101197S0 (—)]

b. Set seal ring (1) to injector seal drift set [SST: KV101197S0 (—)] (A).

c. Straightly insert seal ring (1), which is set in step 2, to fuel injector

c. Straightly insert seal ring (1), which is set in step 2, to fuel injector as shown in the figure and install.

CAUTION:
Be careful that seal ring does not exceed the groove portion of fuel injector.
d. Insert injector seal drift set [SST: KV101197S0 (—)] (A) to injector

d. Insert injector seal drift set [SST: KV101197S0 (—)] (A) to injector and rotate clockwise and counterclockwise by 90° while pressing seal ring to fit it.

NOTE

:
Compress seal ring, because this operation is for rectifying stretch of seal ring caused by installation and for preventing sticking when inserting injector into cylinder head.

2. Install O-ring and backup ring to fuel injector. When handing new O-ring

2. Install O-ring and backup ring to fuel injector. When handing new O-ring and backup ring, paying attention to the following caution items: CAUTION:
• Handle O-ring with bare hands. Never wear gloves. • Lubricate O-ring with new engine oil. • Never clean O-ring with solvent. • Check that O-ring and its mating part are free of foreign material. • When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly into fuel tube. • Insert new O-ring straight into fuel rail. Never decenter or twist it.

• Always install the back up ring (1) in the right direction as instructed.

3. Install fuel injector (1) to fuel rail (2) as per the following:

3. Install fuel injector (1) to fuel rail (2) as per the following:

3 : O-ring (blue)
4 : Backup ring

a. Install fuel injector holder (5) to fuel injector.

• Be careful to keep fuel injector holder from interfering with O-ring. If interference occurs, replace O-ring.

b. Insert fuel injector into fuel rail with fuel injector holder attached.

• Insert it while matching it to the axial center.

• Insert so that protrusion (A) of fuel injector is aligned to cutout (B).

c. Check that installation is complete by checking that fuel injector does not rotate or come off.

• Check that protrusions of fuel injectors and fuel rail are aligned with cutouts of clips after installation.

4. Insert insulator into mounting hole of fuel injector of cylinder head.

4. Insert insulator into mounting hole of fuel injector of cylinder head. 5. Install fuel pressure sensor, if removed. 6. Install fuel tube adaptor, if removed. • Install O-ring and backup ring to fuel tube adaptor. When handing new O-ring and backup ring, paying attention to the following caution items: CAUTION:
• Handle O-ring with bare hands. Never wear gloves. • Lubricate O-ring with new engine oil. • Never clean O-ring with solvent. • Check that O-ring and its mating part are free of foreign material. • When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly into fuel tube. • Insert new O-ring straight into fuel rail. Never decenter or twist it.

• Always install the back up ring in the right direction as instructed.

- Since the cross sections of fuel tube adapter and back up ring are tapered, be careful with the mounting direction.

7. Install fuel rail and fuel injector assembly to cylinder head.

• Tighten mounting bolts and nuts in two steps in numerical order as shown in the figure.

1st step : 10.0 N·m (1.0 kg-m, 89: Engine front


1st step in-lb): 10 N·m (1.0 kg-m, 89
in-lb)
2nd step ft-lb): 20 N·m (2.1 kg-m, 15
ft-lb)

8. Connect injector harness connector.

8. Connect injector harness connector.

9. Install in the reverse order of removal after this step.

Inspection

Check on Fuel Leakage 1. Turn ignition switch “ON” (with the engine stopped). With fuel pressure applied to fuel piping, check there are no fuel leakage at connection points.

NOTE

:
Use mirrors for checking at points out of clear sight.

2. Start the engine. With engine speed increased, check again that there are no fuel leakage at connection points.

CAUTION:
Never touch the engine immediately after stopped, as the engine becomes extremely hot.