Drive Pinion

| Stud bolt | Connector bracket | Reamer bolt | |||
| Electric controlled coupling assembly | Wave spring | Drive pinion oil seal | |||
| Drive pinion lock nut | Pinion front bearing | Gear carrier | |||
| Collapsible spacer | Drive pinion adjusting shim | Pinion rear bearing | |||
| Drive pinion | Drive gear | Differential case | |||
| Side bearing | Side bearing adjusting shim | Side oil seal | |||
| Rear cover | Stud bolt | Gasket | |||
| Drain plug | Filler plug | Pinion mate thrust washer | |||
| Pinion mate gear | Side gear thrust washer | Side gear | |||
| Pinion mate shaft | Lock pin | ||||
| Oil seal lip | Screw hole | ||||
DISASSEMBLY
Remove electric controlled coupling assembly. Refer to Disassembly and Assembly.
Remove differential assembly. Refer to Disassembly and Assembly.
Remove drive pinion oil seal, using oil seal remover (commercial service tool).
Fit drive pinion socket (A) onto drive pinion spline. Remove drive pinion lock nut, using the pinion nut wrench (B).

| A | : Drive pinion socket [SST: KV38109500 ( — )] |
| B | : Pinion nut wrench [SST: KV38109400 ( — )] |
Press drive pinion assembly out of gear carrier.

Remove pinion front bearing inner race.
Remove collapsible spacer.
Remove pinion rear bearing inner race from drive pinion, using the separator (A) and the puller (B).

| A | : Separator (commercial service tool) |
| B | : Puller (commercial service tool) |
Using a brass rod or equivalent (A), tap pinion front bearing outer race evenly from the 2 cutouts on gear carrier and remove pinion front bearing outer race.

Using a brass rod or equivalent (A), tap drive pinion adjusting shim evenly from the 2 cutouts on gear carrier and remove drive pinion adjusting shim and pinion rear bearing outer race.

Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Install a drive pinion adjusting shim of the same thickness as was installed prior to disassembly. Press pinion rear bearing outer race into gear carrier, using the drift (A) [SST: ST33200000 (J-26082)].

Do not reuse pinion rear bearing outer race.
Press pinion front bearing outer race into gear carrier, using the drift (A) [SST: ST33230000 (J-25805-01)].

Do not reuse pinion front bearing outer race.
Press pinion rear bearing inner race to drive pinion, using the drift (A) [SST: ST23860000 ( — )].

Check and adjust the tooth contact and back lash of drive gear and drive pinion following the procedure below.Assemble drive pinion into gear carrier.
Assemble pinion front bearing inner race to drive pinion assembly. Using the drifts (A and C) and press stand (B), press pinion front bearing inner race to drive pinion as far as drive pinion lock nut can be tightened.
| A | : Drift [SST: KV40100610 (J-26089)] |
| B | : Press stand [SST: ST38220000 ( — )] |
| C | : Drift [SST: ST23860000 ( — )] |

| A | : Drive pinion socket [SST: KV38109500 ( — )] |
| B | : Pinion nut wrench [SST: KV38109400 ( — )] |
| C | : Preload gauge [SST: ST3127S000 (J-25765-A)] |
| Pinion bearing preload | : Refer to Preload Torque. |
Assemble collapsible spacer
to drive pinion
.

Assemble drive pinion into gear carrier.
Assemble pinion front bearing inner race to drive pinion assembly.
Using the drifts (A and C) and press stand (B), press pinion front bearing inner race to drive pinion as far as drive pinion lock nut can be tightened.

| A | : Drift [SST: KV40100610 (J-26089)] |
| B | : Press stand [SST: ST38220000 ( — )] |
| C | : Drift [SST: ST23860000 ( — )] |
Apply anti-corrosion oil to the thread and seat of drive pinion lock nut, and temporarily tighten drive pinion lock nut to drive pinion.
Fit the drive pinion socket (A) onto the drive pinion. While holding drive pinion, tighten drive pinion lock nut within the limits of specified torque so as to keep the pinion bearing preload within a standard values, using the pinion nut wrench (B) and the preload gauge (C).

| A | : Drive pinion socket [SST: KV38109500 ( — )] |
| B | : Pinion nut wrench [SST: KV38109400 ( — )] |
| C | : Preload gauge [SST: ST3127S000 (J-25765-A)] |
| Drive pinion lock nut tightening torque | : Refer to Exploded View. |
| Pinion bearing preload | : Refer to Preload Torque. |
Install differential assembly. Refer to Disassembly and Assembly.
Check and adjust drive gear runout, tooth contact, and drive gear to drive pinion backlash. Refer to Adjustment.
Remove dummy cover set, then install rear cover, and side oil seal. Refer to Disassembly and Assembly.
Check total preload torque. Refer to Adjustment.
Using the drift (A) [SST: ST35271000 (J-26091)], install drive pinion oil seal
within the dimension (D) shown as follows.

| D | : 0.8 – 1.2 mm (0.031 – 0.047 in) |
Install electric controlled coupling assembly. Refer to Disassembly and Assembly.
INSPECTION AFTER DISASSEMBLY
Drive Gear and Drive Pinion
Clean up the disassembled parts.
If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.
If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive gear and drive pinion as a set.
Bearing
Clean up the disassembled parts.
If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is observed, replace as a bearing assembly (as a new set).
Oil Seal
Whenever disassembled, replace.
If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.