Differential Assembly

| Stud bolt | Connector bracket | Reamer bolt | |||
| Electric controlled coupling assembly | Wave spring | Drive pinion oil seal | |||
| Drive pinion lock nut | Pinion front bearing | Gear carrier | |||
| Collapsible spacer | Drive pinion adjusting shim | Pinion rear bearing | |||
| Drive pinion | Drive gear | Differential case | |||
| Side bearing | Side bearing adjusting shim | Side oil seal | |||
| Rear cover | Stud bolt | Gasket | |||
| Drain plug | Filler plug | Pinion mate thrust washer | |||
| Pinion mate gear | Side gear thrust washer | Side gear | |||
| Pinion mate shaft | Lock pin | ||||
| Oil seal lip | Screw hole | ||||
DISASSEMBLY
Remove drain plug, filler plug and gaskets.
Remove the side oil seal, using oil seal remover (commercial service tool).

Remove rear cover mounting bolts.
Set drifts (A and B) to the right and left side bearing adjusting shims individually. Press differential assembly with side bearing to remove gear carrier assembly and rear cover assembly.

| A | : Drift [SST: KV40100610 (J-26089)] |
| B | : Drift [SST: KV40100610 (J-26089)] |
Remove stud bolt from rear cover.
Remove side bearing adjusting shims and side bearing outer races.
Remove side bearing inner races, using adaptor (A), separator (B) and puller (C).

| A | : Adaptor [SST: ST33052000 ( — )] |
| B | : Separator (commercial service tool) |
| C | : Puller (commercial service tool) |
For proper reinstallation, paint matching marks
on one differential assembly and drive gear.

Remove drive gear mounting bolts and then remove drive gear from differential assembly.
Remove lock pin of pinion mate shaft, using the pin punch (commercial service tool).

Remove pinion mate shaft.

Remove pinion mate gears, pinion mate thrust washers, side gears, side gear thrust washers from differential case.


Perform inspection after disassembly. Refer to Inspection.
ASSEMBLY
Install side gear thrust washers with the same thickness as the ones installed prior to disassembly or reinstall the old ones on the side gears.

Install side gears and side gear thrust washers into differential case.

Align 2 pinion mate gears in diagonally opposite positions, then rotate and install them into differential case after installing thrust washer to pinion mate gear.


Align the lock pin holes on differential case with pinion mate shaft, and install pinion mate shaft.

Measure side gear end play. If necessary, select the appropriate side gear thrust washers.Place differential assembly straight up so that side gear to be measured comes upward.


| Side gear back clearance | : Refer to Differential Side Gear Clearance. |
If the back clearance is outside the specification, use a thicker/thinner side gear thrust washer to adjust. For selecting thrust washer, refer to the latest parts information.
When the back clearance is large : Use a thicker thrust washer. When the back clearance is small : Use a thinner thrust washer.
Drive a lock pin into pinion mate shaft, using the pin punch (commercial service tool).

Press side bearing inner races to differential assembly, using the drifts (A and B).

| A | : Drift [SST: KV40105020 ( — )] |
| B | : Drift [SST: KV40105020 ( — )] |
Apply thread locking sealant into the thread hole of drive gear.

For applying thread locking sealant, refer to Exploded View.
Install the drive gear to differential assembly.
Tighten the bolts in a crisscross fashion to the specified torque.

For tightening torque, refer to Exploded View.
Assemble side bearing outer races to inner races.
Install new side bearing adjusting shims (2 pieces for one side) with the same thickness as the ones installed prior to disassembly or re-install the old ones, on side bearing outer race of differential assembly.
If side bearing adjusting shims have been already selected, use them.
Set the drifts (A and B) to the right and left side bearing adjusting shims individually. Compress differential assembly and side bearing to gear carrier assembly to install differential assembly.

| A | : Drift [KV40100610 (J-26089)] |
| B | : Drift [KV40100610 (J-26089)] |
Install dummy cover set, check and adjust drive gear runout, tooth contact, backlash, and total preload torque. Refer to Adjustment.
Remove dummy cover set.
Install stud bolt to rear cover.
Apply liquid gasket to mating surface of rear cover.

For applying liquid gasket, refer to Exploded View.
Set the drifts (A and B) to the right and left side bearing adjusting shims individually. Compress differential assembly and side bearing to install rear cover.

| A | : Drift [SST: KV40100610 (J-26089)] |
| B | : Drift [SST: KV40100610 (J-26089)] |
Tighten rear cover mounting bolts to the specified torque.
For tightening torque, refer to Exploded View.
Using the drift (A) [SST: KV38100200 (J-26233)], drive side oil seals until it becomes flush with the gear carrier end.

Check total preload torque. Refer to Adjustment.
TOTAL PRELOAD TORQUE
Remove electric controlled coupling assembly. Refer to Disassembly and Assembly.
Rotate drive pinion back and forth 2 to 3 times to check for unusual noise and rotation malfunction.
Rotate drive pinion at least 20 times to check for smooth operation of the bearing.

Fit drive pinion socket onto drive pinion spline. Measure the total preload, using the preload gauge and drive pinion socket.
| A | : Drive pinion socket [SST: KV38109500 ( — )] |
| B | : Preload gauge [SST: ST3127S000 (J-25765-A)] |
| Total preload torque | : Refer to Preload Torque. |
If measured value is out of the specification, disassemble it to check and adjust each part. Adjust the pinion bearing preload and side bearing preload.
Adjust the pinion bearing preload first, then adjust the side bearing preload.
When the preload torque is large On pinion bearings: Replace the collapsible spacer. On side bearings: Use thinner side bearing adjusting shims. For selecting adjusting shim, refer to the latest parts information. When the preload is small On pinion bearings: Tighten the drive pinion nut. On side bearings: Use thicker side bearing adjusting shims. For selecting adjusting shim, refer to the latest parts information.
DRIVE GEAR RUNOUT
Remove rear cover. Refer to Disassembly and Assembly.
Following the procedure below, install a dummy cover set [SST: KV381086S1 ( — )] to gear carrier.Set dummy cover shims [SST: KV38108630 ( — )] to the right and left side bearing adjusting shims. Temporarily tighten dummy cover [SST: KV38108610 ( — )] to gear carrier. Position dummy cover spacers [SST: KV38108621 ( — )] to dummy cover [SST: KV38108610 ( — )]. Tighten rear cover mounting bolts to the specified torque. Refer to Exploded View. Tighten dummy cover spacer mounting bolts evenly to the specified torque.
| : 5,9 N·m |
Fit a dial indicator (A) to the drive gear back face.

| B | : Dummy cover set [SST: KV381086S1 ( — )] |
Rotate the drive gear to measure runout.
| Drive gear back face runout | : Refer to Drive Gear Runout. |
If the runout is outside of the repair limit, check drive gear assembly condition; foreign material may be caught between drive gear and differential case, or differential case or drive gear may be deformed, etc.
TOOTH CONTACT
Remove rear cover. Refer to Disassembly and Assembly.
Following the procedure below, install a dummy cover set [SST: KV381086S1 ( — )] to gear carrier.Set dummy cover shims [SST: KV38108630 ( — )] to the right and left side bearing adjusting shims. Temporarily tighten dummy cover [SST: KV38108610 ( — )] to gear carrier. Position dummy cover spacers [SST: KV38108621 ( — )] to dummy cover [SST: KV38108610 ( — )]. Tighten rear cover mounting bolts to the specified torque. Refer to Exploded View. Tighten dummy cover spacer mounting bolts evenly to the specified torque.
| : 5,9 N·m |
Apply red lead or equivalent to drive gear.

| A | : Dummy cover set [SST: KV381086S1 ( — )] |
Rotate drive gear back and forth several times, check drive pinion gear to drive gear tooth contact.

Tooth Contact Judgment Guide
If tooth contact is improperly adjusted, follow the procedure below to adjust the pinion height (dimension X).

If the tooth contact is near the face (face contact), or near the heel (heel contact), thicken drive pinion gear adjusting shim to move drive pinion closer to drive gear.

For selecting adjusting shim, refer to the latest parts information.
If the tooth contact is near the flank (flank contact), or near the toe (toe contact), thin drive pinion gear adjusting shim to move drive pinion farther from drive gear.

For selecting adjusting shim, refer to the latest parts information.
BACKLASH
Remove rear cover. Refer to Disassembly and Assembly.
Following the procedure below, install a dummy cover set [SST: KV381086S1 ( — )] to gear carrier.Set dummy cover shims [SST: KV38108630 ( — )] to the right and left side bearing adjusting shims. Temporarily tighten dummy cover [SST: KV38108610 ( — )] to gear carrier. Position dummy cover spacers [SST: KV38108621 ( — )] to dummy cover [SST: KV38108610 ( — )]. Tighten rear cover mounting bolts to the specified torque. Refer to Exploded View. Tighten dummy cover spacer mounting bolts evenly to the specified torque.
| : 5,9 N·m |
Fit a dial indicator (A) to the drive gear face to measure the backlash.

| B | : Dummy cover set [SST: KV381086S1 ( — )] |
| Backlash | : Refer to Backlash. |
If the backlash is outside of the specified value, change the thickness of side bearing adjusting shims.
| When the backlash is large: | |
| Make drive gear back adjusting shims thicker, and drive gear front adjusting shims thinner. For selecting adjusting shim, refer to the latest parts information. | |
| When the backlash is small: | |
| Make drive gear back adjusting shims thinner, and drive gear front adjusting shims thicker. For selecting adjusting shim, refer to the latest parts information. | |
INSPECTION AFTER DISASSEMBLY
Drive Gear and Drive Pinion
Clean up the disassembled parts.
If the gear teeth never mesh or line-up correctly, determine the cause and adjust or replace as necessary.
If the gears are worn, cracked, damaged, pitted or chipped (by friction) noticeably, replace with new drive gear and drive pinion as a set.
Bearing
Clean up the disassembled parts.
If any chipped (by friction), pitted, worn, rusted or scratched marks, or unusual noise from the bearing is observed, replace as a bearing assembly (as a new set).
Oil Seal
Whenever disassembled, replace.
If wear, deterioration of adherence (sealing force lips), or damage is detected on the lips, replace them.
Differential Assembly
DIFFERENTIAL CASE
Clean up the disassembled parts.
If any wear or crack on the contact sides of the differential case is found, replace.
SIDE GEAR AND PINION MATE GEAR

Clean up the disassembled parts.
If any cracks or damage on the surface of the tooth is found, replace.
If any worn or chipped mark on the contact sides of the thrust washer is found, replace.
SIDE GEAR THRUST WASHER AND PINION MATE THRUST WASHER
Clean up the disassembled parts.
If it is chipped (by friction), damaged, or unusually worn, replace.