Active Noise Control ECU Communication Stop Mode. Air Conditioning Amplifier Communication Stop Mode. ECU Malfunction (B1003)
Active Noise Control ECU Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Active Noise Control ECU Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (STEREO COMPONENT EQUALIZER ASSEMBLY BRANCH LINE)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the G68 stereo component equalizer assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (STEREO COMPONENT EQUALIZER ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G68-13 (ACC) - Body ground |
Engine switch on (ACC) |
11 to 14 V |
G68-14 (+B) - Body ground |
Always |
11 to 14 V |
G68-27 (IGN) - Body ground |
Engine switch on (IG) |
11 to 14 V |
| OK | REPLACE STEREO COMPONENT EQUALIZER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
Air Conditioning Amplifier Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Air Conditioning Amplifier Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the G35 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G35-1 (B) - Body ground |
Always |
11 to 14 V |
G35-2 (IG+) - Body ground |
Engine switch on (IG) |
11 to 14 V |
| OK | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
ECU Malfunction (B1003)
DESCRIPTION
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
B1003 |
ECU Malfunction |
A malfunction in the non-volatile storage of the central gateway ECU (network gateway ECU) is detected. |
Central gateway ECU (network gateway ECU) |
- |
PROCEDURE
RECONFIRM DTC OUTPUT
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Central Gateway / Trouble Codes.
Body Electrical > Central Gateway > Trouble CodesResult | Proceed to |
|---|---|
DTC B1003 is not output from the central gateway ECU (network gateway ECU) |
A |
DTC B1003 is output from the central gateway ECU (network gateway ECU) |
B |
| A | USE SIMULATION METHOD TO CHECK |
| B | REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |



