System Diagram. Terminals Of Ecu. Tilt and Telescopic ECU Communication Stop Mode
System Diagram
SYSTEM DIAGRAM
(a) The CAN communication system is composed of 5 buses.
![]() |
CAN Main Bus Line |
![]() |
Terminating Resistor |
![]() |
CAN Branch Line |
* |
Gateway Function Equipped ECU |
![]() |
Bus Monitoring Direction |
- |
- |
Connected to | Code | ECU/Sensor Name | CAN DTC Storage | Note |
|---|---|---|---|---|
- |
CGW |
Central Gateway ECU (Network Gateway ECU) |
- |
- |
- |
DLC3 |
DLC3 |
- |
- |
Bus 1 |
F-CAM |
Forward Recognition Camera |
Available |
- |
F-MR |
Millimeter Wave Radar Sensor Assembly |
- |
- |
|
GRS |
Swing Grille Actuator Assembly |
- |
- |
|
DS |
Driving Support ECU Assembly |
Available |
- |
|
BSM |
Blind Spot Monitor Sensor RH |
Available |
- |
|
R-CA |
Television Camera Assembly |
Available |
- |
|
CS |
Clearance Warning ECU Assembly |
Available |
w/ Intelligent Clearance Sonar System |
|
PAC |
Parking Assist ECU |
Available |
w/ Panoramic View Monitor System |
|
CAN J/C NO. 1 |
No. 1 CAN Junction Connector |
- |
- |
|
CAN J/C NO. 7 |
No. 7 CAN Junction Connector |
- |
- |
|
Bus 2 |
HV |
Hybrid Vehicle Control ECU |
Available |
- |
F-MGC |
Inverter with Converter Assembly |
Available |
- |
|
BRK |
Brake Booster with Master Cylinder Assembly |
Available |
- |
|
ENG |
ECM |
Available |
- |
|
CAN J/C NO. 2 |
No. 2 CAN Junction Connector |
- |
- |
|
CAN J/C NO. 4 |
No. 4 CAN Junction Connector |
- |
- |
|
Bus 3 |
AV |
Radio and Display Receiver Assembly |
Available |
- |
DCM |
DCM (Telematics Transceiver) |
Available |
- |
|
CAN J/C NO. 4 |
No. 4 CAN Junction Connector |
- |
- |
|
Bus 4 |
TPMS |
Tire Pressure Warning ECU and Receiver |
Available |
- |
OCS |
Occupant Detection ECU |
Available |
- |
|
BRK |
Brake Booster with Master Cylinder Assembly |
Available |
- |
|
PKB |
Brake Actuator Assembly |
Available |
- |
|
EPS |
Rack and Pinion Power Steering Gear Assembly |
Available |
- |
|
ENG |
ECM |
Available |
- |
|
HV |
Hybrid Vehicle Control ECU |
Available |
- |
|
STR |
Steering Sensor |
- |
- |
|
SRS |
Airbag ECU Assembly |
Available |
- |
|
CAN J/C NO. 2 |
No. 2 CAN Junction Connector |
- |
- |
|
CAN J/C NO. 4 |
No. 4 CAN Junction Connector |
- |
- |
|
J/C NO. 1 |
No. 1 Junction Connector |
- |
- |
|
Bus 5 |
LITS |
Headlight ECU Sub-assembly RH |
Available |
w/ Cornering Light |
MIR-R |
Outer Mirror Control ECU Assembly RH |
Available |
w/ Seat Position Memory System |
|
DST |
Position Control ECU Assembly LH |
- |
w/ Seat Position Memory System |
|
MIR-L |
Outer Mirror Control ECU Assembly LH |
Available |
w/ Seat Position Memory System |
|
A/C |
Air Conditioning Amplifier Assembly |
Available |
- |
|
MB |
Main Body ECU (Multiplex Network Body ECU) |
Available |
Connected to LIN communication system |
|
HUD |
Meter Mirror Sub-assembly |
Available |
w/ Headup Display System |
|
SMT |
Certification ECU (Smart Key ECU Assembly) |
Available |
- |
|
LITM |
Headlight ECU Sub-assembly LH |
Available |
w/ Cornering Light |
|
T&T |
Multiplex Tilt and Telescopic ECU |
Available |
w/ Power Tilt and Power Telescopic System |
|
MET |
Combination Meter Assembly |
Available |
- |
|
CAN J/C NO. 3 |
No. 3 CAN Junction Connector |
- |
- |
|
CAN J/C NO. 6 |
No. 6 CAN Junction Connector |
- |
- |
|
J/C NO. 2 |
No. 2 Junction Connector |
- |
- |
|
J/C NO. 3 |
No. 3 Junction Connector |
- |
- |
Terminals Of Ecu
TERMINALS OF ECU
NOTICE:
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- This section describes the standard values for all CAN related components.
HINT:
- The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
Click here

- Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
- Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
NO. 1 CAN JUNCTION CONNECTOR
(a) Check the No. 1 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 1 CAN Junction Connector) |
*b |
to Millimeter Wave Radar Sensor Assembly |
*c |
to Forward Recognition Camera |
*d |
to Central Gateway ECU (Network Gateway ECU) |
*e |
to Swing Grille Actuator Assembly |
*f |
to No. 7 CAN Junction Connector |
(2) Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
A48-1 (CANH) |
R |
Millimeter wave radar sensor assembly (for Bus 1) |
A48-7 (CANL) |
W |
|
A48-2 (CANH) |
G |
Forward recognition camera (for Bus 1) |
A48-8 (CANL) |
W |
|
A48-3 (CANH) |
P |
Central gateway ECU (network gateway ECU) (for Bus 1) |
A48-9 (CANL) |
W |
|
A48-4 (CANH) |
G |
Swing grille actuator assembly (for Bus 1) |
A48-10 (CANL) |
W |
|
A48-5 (CANH) |
B |
No. 7 CAN junction connector (for Bus 1) |
A48-11 (CANL) |
W |
NO. 2 CAN JUNCTION CONNECTOR
(a) Check the No. 2 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 2 CAN Junction Connector) |
*b |
to Brake Booster with Master Cylinder Assembly |
*c |
to No. 1 Junction Connector |
*d |
to ECM |
*e |
to Rack and Pinion Power Steering Gear Assembly |
*f |
to No. 4 CAN Junction Connector |
*g |
to Brake Actuator Assembly |
*h |
to Inverter with Converter Assembly |
(2) Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
A49-1 (CANH) |
Y |
Brake booster with master cylinder assembly (for Bus 4) |
A49-12 (CANL) |
W |
|
A49-2 (CANH) |
R |
No. 1 junction connector (for Bus 4) |
A49-13 (CANL) |
W |
|
A49-3 (CANH) |
P |
ECM (for Bus 4) |
A49-14 (CANL) |
W |
|
A49-4 (CANH) |
G |
Rack and pinion power steering gear assembly (for Bus 4) |
A49-15 (CANL) |
W |
|
A49-5 (CANH) |
GR |
No. 4 CAN junction connector (for Bus 4) |
A49-16 (CANL) |
W |
|
A49-6 (CANH) |
B |
Brake actuator assembly (for Bus 4) |
A49-17 (CANL) |
W |
|
A49-8 (CANH) |
V |
Inverter with converter assembly (for Bus 2) |
A49-19 (CANL) |
W |
|
A49-9 (CANH) |
LG |
Brake booster with master cylinder assembly (for Bus 2) |
A49-20 (CANL) |
W |
|
A49-10 (CANH) |
L |
No. 4 CAN junction connector (for Bus 2) |
A49-21 (CANL) |
W |
|
A49-11 (CANH) |
B |
ECM (for Bus 2) |
A49-22 (CANL) |
W |
NO. 3 CAN JUNCTION CONNECTOR
(a) Check the No. 3 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 3 CAN Junction Connector) |
*b |
to No. 3 Junction Connector |
*c |
to Certification ECU (Smart Key ECU Assembly) |
*d |
to Combination Meter Assembly |
*e |
to Main Body ECU (Multiplex Network Body ECU) |
*f |
to Air Conditioning Amplifier Assembly |
*g |
to Headlight ECU Sub-assembly LH (w/ Cornering Light) |
*h |
to Meter Mirror Sub-assembly (w/ Headup Display System) |
*i |
to Multiplex Tilt and Telescopic ECU (w/ Power Tilt and Power Telescopic System) |
- |
- |
(2) Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
G94-3 (CANH) |
P |
No. 3 junction connector (for Bus 5) |
G94-14 (CANL) |
W |
|
G94-4 (CANH) |
G |
Certification ECU (smart key ECU assembly) (for Bus 5) |
G94-15 (CANL) |
W |
|
G94-5 (CANH) |
B |
Combination meter assembly (for Bus 5) |
G94-16 (CANL) |
W |
|
G94-6 (CANH) |
BE |
Main body ECU (multiplex network body ECU) (for Bus 5) |
G94-17 (CANL) |
W |
|
G94-7 (CANH) |
SB |
Air conditioning amplifier assembly (for Bus 5) |
G94-18 (CANL) |
W |
|
G94-8 (CANH) |
L |
Headlight ECU sub-assembly LH*1 (for Bus 5) |
G94-19 (CANL) |
W |
|
G94-9 (CANH) |
LG |
Meter mirror sub-assembly*2 (for Bus 5) |
G94-20 (CANL) |
W |
|
G94-10 (CANH) |
R |
Multiplex tilt and telescopic ECU*3 (for Bus 5) |
G94-21 (CANL) |
W |
- *1: w/ Cornering Light
- *2: w/ Headup Display System
- *3: w/ Power Tilt and Power Telescopic System
NO. 4 CAN JUNCTION CONNECTOR
(a) Check the No. 4 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 4 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to No. 2 CAN Junction Connector |
*d |
to Steering Sensor |
*e |
to DCM (Telematics Transceiver) |
- |
- |
(2) Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
G95-1 (CANH) |
SB |
Central gateway ECU (network gateway ECU) (for Bus 2) |
G95-12 (CANL) |
W |
|
G95-6 (CANH) |
SB |
No. 2 CAN junction connector (for Bus 4) |
G95-17 (CANL) |
W |
|
G95-7 (CANH) |
G |
Steering sensor (for Bus 4) |
G95-18 (CANL) |
W |
|
G95-9 (CANH) |
L |
Central gateway ECU (network gateway ECU) (for Bus 3) |
G95-20 (CANL) |
W |
|
G95-10 (CANH) |
R |
DCM (telematics transceiver) (for Bus 3) |
G95-21 (CANL) |
W |
|
G95-11 (CANH) |
GR |
Central gateway ECU (network gateway ECU) (for Bus 3) |
G95-22 (CANL) |
W |
(b) Check the No. 4 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 4 CAN Junction Connector) |
*b |
to Radio and Display Receiver Assembly |
*c |
to Hybrid Vehicle Control ECU |
*d |
to Airbag ECU Assembly |
*e |
to No. 2 CAN Junction Connector |
- |
- |
(2) Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
G96-1 (CANH) |
B |
Radio and display receiver assembly (for Bus 3) |
G96-12 (CANL) |
W |
|
G96-5 (CANH) |
G |
Hybrid vehicle control ECU (for Bus 4) |
G96-16 (CANL) |
W |
|
G96-6 (CANH) |
R |
Airbag ECU assembly (for Bus 4) |
G96-17 (CANL) |
W |
|
G96-9 (CANH) |
L |
Hybrid vehicle control ECU (for Bus 2) |
G96-20 (CANL) |
W |
|
G96-11 (CANH) |
G |
No. 2 CAN junction connector (for Bus 2) |
G96-22 (CANL) |
W |
NO. 6 CAN JUNCTION CONNECTOR
(a) Check the No. 6 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 6 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to No. 2 Junction Connector |
*d |
to Outer Mirror Control ECU Assembly RH (w/ Seat Position Memory System) |
*e |
to Headlight ECU Sub-assembly RH (w/ Cornering Light) |
- |
- |
(2) Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
K65-1 (CANH) |
G |
Central gateway ECU (network gateway ECU) (for Bus 5) |
K65-12 (CANL) |
W |
|
K65-2 (CANH) |
L |
No. 2 junction connector (for Bus 5) |
K65-13 (CANL) |
W |
|
K65-3 (CANH) |
GR |
Outer mirror control ECU assembly RH*1 (for Bus 5) |
K65-14 (CANL) |
W |
|
K65-5 (CANH) |
G |
Headlight ECU sub-assembly RH*2 (for Bus 5) |
K65-16 (CANL) |
W |
- *1: w/ Seat Position Memory System
- *2: w/ Cornering Light
NO. 7 CAN JUNCTION CONNECTOR
(a) Check the No. 7 CAN junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 7 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to Clearance Warning ECU Assembly (w/ Intelligent Clearance Sonar System) |
*d |
to Blind Spot Monitor Sensor RH |
*e |
to Television Camera Assembly |
*f |
to No. 1 CAN Junction Connector |
*g |
to Parking Assist ECU (w/ Panoramic View Monitor System) |
*h |
to Driving Support ECU Assembly |
(2) Check the connection diagram of the components which are connected to the No. 7 CAN junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
K66-1 (CANH) |
GR |
Central gateway ECU (network gateway ECU) (for Bus 1) |
K66-11 (CANL) |
W |
|
K66-2 (CANH) |
L |
Clearance warning ECU assembly*1 (for Bus 1) |
K66-12 (CANL) |
W |
|
K66-3 (CANH) |
BE |
Blind spot monitor sensor RH (for Bus 1) |
K66-13 (CANL) |
W |
|
K66-4 (CANH) |
R |
Television camera assembly (for Bus 1) |
K66-14 (CANL) |
W |
|
K66-5 (CANH) |
B |
No. 1 CAN junction connector (for Bus 1) |
K66-15 (CANL) |
W |
|
K66-8 (CANH) |
GR |
Parking assist ECU*2 (for Bus 1) |
K66-18 (CANL) |
W |
|
K66-9 (CANH) |
R |
Driving support ECU assembly (for Bus 1) |
K66-19 (CANL) |
W |
- *1: w/ Intelligent Clearance Sonar System
- *2: w/ Panoramic View Monitor System
NO. 1 JUNCTION CONNECTOR
(a) Check the No. 1 junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 1 Junction Connector) |
*b |
to Tire Pressure Warning ECU and Receiver |
*c |
to Occupant Detection ECU |
*d |
to Central Gateway ECU (Network Gateway ECU) |
*e |
to No. 2 CAN Junction Connector |
- |
- |
(2) Check the connection diagram of the components which are connected to the No. 1 junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
K67-8 (CANH) |
L |
Tire pressure warning ECU and receiver (for Bus 4) |
K67-19 (CANL) |
W |
|
K67-9 (CANH) |
GR |
Occupant detection ECU (for Bus 4) |
K67-20 (CANL) |
W |
|
K67-10 (CANH) |
G |
Central gateway ECU (network gateway ECU) (for Bus 4) |
K67-21 (CANL) |
W |
|
K67-11 (CANH) |
LG |
No. 2 CAN junction connector (for Bus 4) |
K67-22 (CANL) |
W |
NO. 2 JUNCTION CONNECTOR
(a) Check the No. 2 junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 2 Junction Connector) |
*b |
to No. 6 CAN Junction Connector |
*c |
to No. 3 Junction Connector |
*d |
to Position Control ECU Assembly LH (w/ Seat Position Memory System) |
(2) Check the connection diagram of the components which are connected to the No. 2 junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
K69-1 (CANH) |
L |
No. 6 CAN junction connector (for Bus 5) |
K69-12 (CANL) |
W |
|
K69-2 (CANH) |
L |
No. 3 junction connector (for Bus 5) |
K69-13 (CANL) |
W |
|
K69-3 (CANH) |
G |
Position control ECU assembly LH* (for Bus 5) |
K69-14 (CANL) |
W |
- *: w/ Seat Position Memory System
NO. 3 JUNCTION CONNECTOR
(a) Check the No. 3 junction connector.
(1) Connection diagram
*a |
Front view of wire harness connector (to No. 3 Junction Connector) |
*b |
to Outer Mirror Control ECU Assembly LH (w/ Seat Position Memory System) |
*c |
to No. 3 CAN Junction Connector |
*d |
to No. 2 Junction Connector |
(2) Check the connection diagram of the components which are connected to the No. 3 junction connector.
Terminal No. (Symbol) | Wiring Color | Connected to |
|---|---|---|
K64-1 (CANH) |
LG |
Outer mirror control ECU assembly LH* (for Bus 5) |
K64-12 (CANL) |
W |
|
K64-3 (CANH) |
B |
No. 3 CAN junction connector (for Bus 5) |
K64-14 (CANL) |
W |
|
K64-4 (CANH) |
L |
No. 2 junction connector (for Bus 5) |
K64-15 (CANL) |
W |
- *: w/ Seat Position Memory System
DLC3
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G45-6 (CANH) - G45-14 (CANL) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G45-6 (CANH) - G45-4 (CG) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G45-14 (CANL) - G45-4 (CG) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G45-6 (CANH) - G45-16 (BAT) |
B - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G45-14 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)
*a |
Component without harness connected (Central Gateway ECU (Network Gateway ECU)) |
- |
- |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G52 central gateway ECU (network gateway ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Central Gateway ECU (Network Gateway ECU)) |
- |
- |
Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-14 (CA6H) - G52-5 (CA6L) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
1 MΩ or higher |
G52-14 (CA6H) - G52-10 (GND) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-5 (CA6L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-14 (CA6H) - G52-1 (BATT) |
B - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-5 (CA6L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-23 (CA1H) - G52-9 (CAXH) |
B - BE |
HIGH-level CAN bus line - HIGH-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
G52-8 (CA1L) - G52-24 (CAXL) |
W - W |
LOW-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
G52-23 (CA1H) - G52-10 (GND) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-8 (CA1L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-23 (CA1H) - G52-1 (BATT) |
B - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-8 (CA1L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-18 (CA4H) - G52-17 (CA4L) |
SB - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
G52-18 (CA4H) - G52-10 (GND) |
SB - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-17 (CA4L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-18 (CA4H) - G52-1 (BATT) |
SB - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-17 (CA4L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-6 (CA3H) - G52-19 (CAYH) |
L - GR |
HIGH-level CAN bus line - HIGH-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
G52-21 (CA3L) - G52-20 (CAYL) |
W - W |
LOW-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
Below 1 Ω |
G52-6 (CA3H) - G52-10 (GND) |
L - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-21 (CA3L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-6 (CA3H) - G52-1 (BATT) |
L - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-21 (CA3L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-22 (CA2H) - G52-7 (CA2L) |
G - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
G52-22 (CA2H) - G52-10 (GND) |
G - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-7 (CA2L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-22 (CA2H) - G52-1 (BATT) |
G - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-7 (CA2L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G52-15 (CA5H) - G52-16 (CA5L) |
LG - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
G52-15 (CA5H) - G52-10 (GND) |
LG - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-16 (CA5L) - G52-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G52-15 (CA5H) - G52-1 (BATT) |
LG - BE |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-16 (CA5L) - G52-1 (BATT) |
W - BE |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
STEERING SENSOR
*a |
Component without harness connected (Steering Sensor) |
- |
- |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G48 steering sensor connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Steering Sensor) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G48-3 (CANH) - G48-8 (CANL) |
G - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G48-3 (CANH) - G48-6 (ESS) |
G - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G48-8 (CANL) - G48-6 (ESS) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G48-3 (CANH) - G48-4 (BAT) |
G - GR |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G48-8 (CANL) - G48-4 (BAT) |
W - GR |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
HYBRID VEHICLE CONTROL ECU
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G46 and G47 hybrid vehicle control ECU connectors.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Hybrid Vehicle Control ECU) |
- |
- |
Standard Resistance:
Bus 2 Branch LinesTerminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G47-25 (CA1H) - G47-24 (CA1L) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G47-25 (CA1H) - G46-6 (E1) |
L - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G47-24 (CA1L) - G46-6 (E1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G47-25 (CA1H) - G47-3 (BATT) |
L - B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G47-24 (CA1L) - G47-3 (BATT) |
W - B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G47-31 (CA3P) - G47-30 (CA3N) |
G - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G47-31 (CA3P) - G46-6 (E1) |
G - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G47-30 (CA3N) - G46-6 (E1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G47-31 (CA3P) - G47-3 (BATT) |
G - B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G47-30 (CA3N) - G47-3 (BATT) |
W - B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
INVERTER WITH CONVERTER ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A42 inverter with converter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Inverter with Converter Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A42-1 (CANH) - A42-7 (CANL) |
V - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A42-1 (CANH) - A42-24 (GND1) |
V - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A42-7 (CANL) - A42-24 (GND1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A42-1 (CANH) - G45-16 (BAT) |
V - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A42-7 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
ECM
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A19 ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to ECM) |
- |
- |
Standard Resistance:
Bus 2 Main LinesTerminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A19-8 (CANH) - A19-18 (CANL) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
A19-8 (CANH) - A19-10 (E1) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A19-18 (CANL) - A19-10 (E1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A19-8 (CANH) - A19-1 (BATT) |
B - G |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A19-18 (CANL) - A19-1 (BATT) |
W - G |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A19-7 (CAN+) - A19-17 (CAN-) |
P - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A19-7 (CAN+) - A19-10 (E1) |
P - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A19-17 (CAN-) - A19-10 (E1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A19-7 (CAN+) - A19-1 (BATT) |
P - G |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A19-17 (CAN-) - A19-1 (BATT) |
W - G |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
COMBINATION METER ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G16 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Combination Meter Assembly) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G16-32 (CANH) - G16-31 (CANL) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
G16-32 (CANH) - G16-21 (ES) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G16-31 (CANL) - G16-21 (ES) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G16-32 (CANH) - G16-40 (B) |
B - LA-B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G16-31 (CANL) - G16-40 (B) |
W - LA-B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A35 brake booster with master cylinder assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Bus 2 Branch LinesTerminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A35-30 (CA2H) - A35-29 (CA2L) |
LG - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A35-30 (CA2H) - A35-26 (GND1) |
LG - LA |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A35-29 (CA2L) - A35-26 (GND1) |
W - LA |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A35-30 (CA2H) - A35-52 (BS) |
LG - LG |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A35-29 (CA2L) - A35-52 (BS) |
W - LG |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A35-43 (CA1H) - A35-42 (CA1L) |
Y - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A35-43 (CA1H) - A35-26 (GND1) |
Y - LA |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A35-42 (CA1L) - A35-26 (GND1) |
W - LA |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A35-43 (CA1H) - A35-52 (BS) |
Y - LG |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A35-42 (CA1L) - A35-52 (BS) |
W - LG |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness connector (to Brake Booster with Master Cylinder Assembly) |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G33 main body ECU (multiplex network body ECU) connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Main Body ECU (Multiplex Network Body ECU)) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G33-5 (CANH) - G33-4 (CANL) |
BE - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G33-5 (CANH) - G45-4 (CG) |
BE - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G33-4 (CANL) - G45-4 (CG) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G33-5 (CANH) - G45-16 (BAT) |
BE - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G33-4 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G40-1 (CANH) - G40-2 (CANL) |
G - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G40-1 (CANH) - G40-18 (E) |
G - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G40-2 (CANL) - G40-18 (E) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G40-1 (CANH) - G40-4 (+B) |
G - B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G40-2 (CANL) - G40-4 (+B) |
W - B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly)) |
RACK AND PINION POWER STEERING GEAR ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the C67 rack and pinion power steering gear assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Rack and Pinion Power Steering Gear Assembly) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
C67-10 (CANH) - C67-11 (CANL) |
G - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
C67-10 (CANH) - C67-7 (PGND) |
G - B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
C67-11 (CANL) - C67-7 (PGND) |
W - B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
C67-10 (CANH) - C67-8 (PIG) |
G - W |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
C67-11 (CANL) - C67-8 (PIG) |
W - W |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
AIRBAG ECU ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G50 airbag ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Airbag ECU Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G50-26 (CANH) - G50-27 (CANL) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
G50-26 (CANH) - G50-33 (E1) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G50-27 (CANL) - G50-33 (E1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G50-26 (CANH) - G45-16 (BAT) |
R - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G50-27 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
AIR CONDITIONING AMPLIFIER ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G35 air conditioning amplifier assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G35-11 (CANH) - G35-12 (CANL) |
SB - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G35-11 (CANH) - G35-4 (GND) |
SB - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G35-12 (CANL) - G35-4 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G35-11 (CANH) - G35-1 (B) |
SB - LA-B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G35-12 (CANL) - G35-1 (B) |
W - LA-B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
RADIO AND DISPLAY RECEIVER ASSEMBLY
Refer to Terminals of ECU.
- for Audio and Visual System
Click here

- for Navigation System
Click here

(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G2 radio and display receiver assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Radio and Display Receiver Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G2-13 (CANH) - G2-14 (CANL) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G2-13 (CANH) - G45-4 (CG) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G2-14 (CANL) - G45-4 (CG) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G2-13 (CANH) - G45-16 (BAT) |
B - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G2-14 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
BLIND SPOT MONITOR SENSOR RH
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the P5 blind spot monitor sensor RH connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Blind Spot Monitor Sensor RH) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
P5-2 (CA1P) - P5-7 (CA1N) |
V - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
P5-2 (CA1P) - P5-10 (BRGD) |
V - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P5-7 (CA1N) - P5-10 (BRGD) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P5-2 (CA1P) - G45-16 (BAT) |
V - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
P5-7 (CA1N) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
FORWARD RECOGNITION CAMERA
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the O5 forward recognition camera connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Forward Recognition Camera) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
O5-5 (CA1P) - O5-11 (CA1N) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
O5-5 (CA1P) - O5-10 (GND) |
L - LA |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
O5-11 (CA1N) - O5-10 (GND) |
W - LA |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
O5-5 (CA1P) - G45-16 (BAT) |
L - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
O5-11 (CA1N) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
MILLIMETER WAVE RADAR SENSOR ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A25 millimeter wave radar sensor assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Millimeter Wave Radar Sensor Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A25-3 (CA2H) - A25-2 (CA2L) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A25-3 (CA2H) - A25-1 (SGND) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A25-2 (CA2L) - A25-1 (SGND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A25-3 (CA2H) - G45-16 (BAT) |
R - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A25-2 (CA2L) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
OCCUPANT DETECTION ECU
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the R7 occupant detection ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Occupant Detection ECU) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
R7-5 (CANP) - R7-4 (CANN) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
R7-5 (CANP) - R7-10 (GND) |
L - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
R7-4 (CANN) - R7-10 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
R7-5 (CANP) - G45-16 (BAT) |
L - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
R7-4 (CANN) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
DCM (TELEMATICS TRANSCEIVER)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G9 DCM (telematics transceiver) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G9-15 (CANP) - G9-16 (CANN) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G9-15 (CANP) - G9-4 (E) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G9-16 (CANN) - G9-4 (E) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G9-15 (CANP) - G9-1 (+B) |
R - B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G9-16 (CANN) - G9-1 (+B) |
W - B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
*a |
Front view of wire harness connector (to DCM (Telematics Transceiver)) |
TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the P7 television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Television Camera Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
P7-4 (CANH) - P7-1 (CANL) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
P7-4 (CANH) - G45-4 (CG) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P7-1 (CANL) - G45-4 (CG) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P7-4 (CANH) - G45-16 (BAT) |
R - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
P7-1 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
TELEVISION CAMERA ASSEMBLY (w/o Panoramic View Monitor System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the P19 television camera assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Television Camera Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
P19-4 (CANH) - P19-1 (CANL) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
P19-4 (CANH) - G45-4 (CG) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P19-1 (CANL) - G45-4 (CG) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
P19-4 (CANH) - G45-16 (BAT) |
R - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
P19-1 (CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
TIRE PRESSURE WARNING ECU AND RECEIVER
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the K11 tire pressure warning ECU and receiver connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Tire Pressure Warning ECU and Receiver) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
K11-9 (CANH) - K11-10 (CANL) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
K11-9 (CANH) - K11-12 (GND) |
L - BR |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K11-10 (CANL) - K11-12 (GND) |
W - BR |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K11-9 (CANH) - K11-7 (+B) |
L - LA-R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
K11-10 (CANL) - K11-7 (+B) |
W - LA-R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
BRAKE ACTUATOR ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A39 brake actuator assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Brake Actuator Assembly) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A39-12 (CANH) - A39-11 (CANL) |
B - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A39-12 (CANH) - A39-1 (MGND) |
B - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A39-11 (CANL) - A39-1 (MGND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A39-12 (CANH) - A39-9 (BEPB) |
B - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A39-11 (CANL) - A39-9 (BEPB) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
METER MIRROR SUB-ASSEMBLY (w/ Headup Display System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the H1 meter mirror sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Meter Mirror Sub-assembly) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
H1-12 (MPX1) - H1-13 (MPX2) |
P - R |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
H1-12 (MPX1) - H1-4 (ES) |
P - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
H1-13 (MPX2) - H1-4 (ES) |
R - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
H1-12 (MPX1) - H1-2 (B) |
P - P |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
H1-13 (MPX2) - H1-2 (B) |
R - P |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Cornering Light)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A8 headlight ECU sub-assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Headlight ECU Sub-assembly LH) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A8-24(CANH) - A8-23(CANL) |
P - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A8-24(CANH)) - A8-12 (GND) |
P - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A8-23(CANL) - A8-12 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A8-24(CANH) - G45-16 (BAT) |
P - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A8-23(CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Cornering Light)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A9 headlight ECU sub-assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Headlight ECU Sub-assembly RH) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A9-24(CANH) - A9-23(CANL) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
A9-24(CANH)) - A9-12 (GND) |
L - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A9-23(CANL) - A9-12 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
A9-24(CANH) - G45-16 (BAT) |
L - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A9-23(CANL) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
SWING GRILLE ACTUATOR ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the z17 swing grille actuator assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Swing Grille Actuator Assembly) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
z17-6(CANP) - z17-5(CANN) |
# |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
z17-6(CANP) - z17-3 (GND) |
# |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
z17-5(CANN) - z17-3 (GND) |
# |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
z17-6(CANP) - z17-1 (+B) |
# |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
z17-5(CANN) - z17-1 (+B) |
# |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
CLEARANCE WARNING ECU ASSEMBLY (w/ Intelligent Clearance Sonar System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the K34 clearance warning ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Clearance Warning ECU Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
K34-17 (R1) - K34-18 (R2) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
K34-17 (R1) - K34-30 (E) |
L - BR |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K34-18 (R2) - K34-30 (E) |
W - BR |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K34-17 (R1) - G45-16 (BAT) |
L - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
K34-18 (R2) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
PARKING ASSIST ECU (w/ Panoramic View Monitor System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the K35 parking assist ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Parking Assist ECU) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
K35-12 (CANH) - K35-13 (CANL) |
GR - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
K35-12 (CANH) - K35-3 (GND1) |
GR - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K35-13 (CANL) - K35-3 (GND1) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
K35-12 (CANH) - K35-2 (+B) |
GR - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
K35-13 (CANL) - K35-2 (+B) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
MULTIPLEX TILT AND TELESCOPIC ECU (w/ Power Tilt and Power Telescopic System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G49 multiplex tilt and telescopic ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Multiplex Tilt and Telescopic ECU) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G49-3 (CANP) - G49-11 (CANN) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G49-3 (CANP) - G49-1 (GND) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G49-11 (CANN) - G49-1 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G49-3 (CANP) - G49-2 (+B) |
R - B |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G49-11 (CANN) - G49-2 (+B) |
W - B |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
DRIVING SUPPORT ECU ASSEMBLY
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G39 driving support ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to Driving Support ECU Assembly) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G39-10 (CA2H) - G39-11 (CA2L) |
R - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
G39-10 (CA2H) - G39-28 (GND) |
R - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G39-11 (CA2L) - G39-28 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
G39-10 (CA2H) - G45-16 (BAT) |
R - R |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G39-11 (CA2L) - G45-16 (BAT) |
W - R |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
POSITION CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the R32 and R33 position control ECU assembly LH connectors.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Position Control ECU Assembly LH) |
- |
- |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
R32-13 (CANP) - R32-14 (CANN) |
L - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
R32-13 (CANP) - R33-2 (E) |
L - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
R32-14 (CANN) - R33-2 (E) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
R32-13 (CANP) - R33-3 (B) |
L - W |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
R32-14 (CANN) - R33-3 (B) |
W - W |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the I21 outer mirror control ECU assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Outer Mirror Control ECU Assembly LH) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I21-9 (CANP) - I21-8 (CANN) |
P - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
I21-9 (CANP) - I21-7 (GND) |
P - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
I21-8 (CANN) - I21-7 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
I21-9 (CANP) - I21-6 (CPUB) |
P - LA-L |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
I21-8 (CANN) - I21-6 (CPUB) |
W - LA-L |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
OUTER MIRROR CONTROL ECU ASSEMBLY RH (w/ Seat Position Memory System)
Refer to Terminals of ECU.
Click here ![]()
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the I5 outer mirror control ECU assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
*a |
Front view of wire harness connector (to Outer Mirror Control ECU Assembly RH) |
Standard Resistance:
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I5-9 (CANP) - I5-8 (CANN) |
P - W |
HIGH-level CAN bus line - LOW-level CAN bus line |
Cable disconnected from negative (-) auxiliary battery terminal |
54 to 69 Ω |
I5-9 (CANP) - I5-7 (GND) |
P - W-B |
HIGH-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
I5-8 (CANN) - I5-7 (GND) |
W - W-B |
LOW-level CAN bus line - Ground |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
I5-9 (CANP) - I5-6 (CPUB) |
P - LA-L |
HIGH-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
I5-8 (CANN) - I5-6 (CPUB) |
W - LA-L |
LOW-level CAN bus line - Auxiliary battery positive (+) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Tilt and Telescopic ECU Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Tilt and Telescopic ECU Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (MULTIPLEX TILT AND TELESCOPIC ECU BRANCH LINE)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G49 multiplex tilt and telescopic ECU connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) auxiliary battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G49-9 (ECUB) - Body ground |
Power switch off |
11 to 14 V |
G49-10 (IG) - Body ground |
Power switch on (IG) |
11 to 14 V |
| OK | REPLACE MULTIPLEX TILT AND TELESCOPIC ECU |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |





