Diagnostic Trouble Code Chart. Door Mirror ECU LH Communication Stop Mode. Door Mirror ECU RH Communication Stop Mode
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Diagnostic Trouble Code ChartDTC No. | Detection Item | Trouble Area | Link |
|---|---|---|---|
B1003 |
ECU Malfunction |
Central gateway ECU (network gateway ECU) |
Door Mirror ECU LH Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Door Mirror ECU LH Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (OUTER MIRROR CONTROL ECU ASSEMBLY LH BRANCH LINE)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I21 outer mirror control ECU assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I21-5 (SIG) - Body ground |
Engine switch on (IG) |
11 to 14 V |
I21-6 (CPUB) - Body ground |
Always |
11 to 14 V |
I21-14 (BDR) - Body ground |
Always |
11 to 14 V |
| OK | REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
Door Mirror ECU RH Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Door Mirror ECU RH Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the engine switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the engine switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (OUTER MIRROR CONTROL ECU ASSEMBLY RH BRANCH LINE)
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the I5 outer mirror control ECU assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I5-5 (SIG) - Body ground |
Engine switch on (IG) |
11 to 14 V |
I5-6 (CPUB) - Body ground |
Always |
11 to 14 V |
I5-14 (BDR) - Body ground |
Always |
11 to 14 V |
| OK | REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |




