Center Airbag Sensor Communication Stop Mode. Certification ECU Communication Stop Mode. Check Bus 1 Line for Short to +B
Center Airbag Sensor Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Center Airbag Sensor Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (AIRBAG ECU ASSEMBLY MAIN LINE)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G50 airbag ECU assembly connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (AIRBAG ECU ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) auxiliary battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G50-36 (IG2) - Body ground |
Power switch on (IG) |
11 to 14 V |
| OK | REPLACE AIRBAG ECU ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
Certification ECU Communication Stop Mode
DESCRIPTION
Detection Item | Symptom | Trouble Area |
|---|---|---|
Certification ECU Communication Stop Mode |
Any of the following conditions are met:
|
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| NG | REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)) |
|
CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
(a) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(b) Reconnect the cable to the negative (-) auxiliary battery terminal.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-4 (+B) - Body ground |
Power switch off |
11 to 14 V |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT) |
Check Bus 1 Line for Short to +B
DESCRIPTION
There may be a short circuit between one of the CAN bus lines and +B when there is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
Symptom | Trouble Area |
|---|---|
There is no resistance between terminal 23 (CA1H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 8 (CA1L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3. |
|
WIRING DIAGRAM
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
- Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here

- Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
- After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here

- After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG) and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h or more for 5 minutes or more.
- After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here

HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the A48 No. 1 CAN junction connector.
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to No. 1 CAN Junction Connector) |
*b |
to Millimeter Wave Radar Sensor Assembly |
*c |
to Forward Recognition Camera |
*d |
to Central Gateway ECU (Network Gateway ECU) |
*e |
to Swing Grille Actuator Assembly |
*f |
to No. 7 CAN Junction Connector |
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
A48-1 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Millimeter wave radar sensor assembly |
A48-7 (CANL) - G45-16 (BAT) |
|||
A48-2 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Forward recognition camera |
A48-8 (CANL) - G45-16 (BAT) |
|||
A48-3 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Central gateway ECU (network gateway ECU) |
A48-9 (CANL) - G45-16 (BAT) |
|||
A48-4 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Swing grille actuator assembly |
A48-10 (CANL) - G45-16 (BAT) |
|||
A48-5 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
No. 7 CAN junction connector |
A48-11 (CANL) - G45-16 (BAT) |
Result | Proceed to |
|---|---|
OK |
A |
NG (Line to central gateway ECU (network gateway ECU)) |
B |
NG (Line to No. 7 CAN junction connector) |
C |
NG (Line to ECU or sensor) |
D |
| A | REPLACE NO. 1 CAN JUNCTION CONNECTOR |
| C | GO TO STEP 3 |
| D | GO TO STEP 5 |
|
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
(a) Disconnect the G52 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to No. 1 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
A48-3 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
A48-9 (CANL) - G45-16 (BAT) |
| OK | REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |
| NG | REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 7 CAN JUNCTION CONNECTOR)
(a) Disconnect the K66 No. 7 CAN junction connector.
(b) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to No. 7 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to Clearance Warning ECU Assembly (w/ Intelligent Clearance Sonar System) |
*d |
to Blind Spot Monitor Sensor RH |
*e |
to Television Camera Assembly |
*f |
to No. 1 CAN Junction Connector |
*g |
to Parking Assist ECU (w/ Panoramic View Monitor System) |
*h |
to Driving Support ECU Assembly |
Standard Resistance:
Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
K66-1 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Central gateway ECU (network gateway ECU) |
K66-11 (CANL) - G45-16 (BAT) |
|||
K66-2 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Clearance warning ECU assembly*1 |
K66-12 (CANL) - G45-16 (BAT) |
|||
K66-3 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Blind spot monitor sensor RH |
K66-13 (CANL) - G45-16 (BAT) |
|||
K66-4 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Television camera assembly |
K66-14 (CANL) - G45-16 (BAT) |
|||
K66-5 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
No. 1 CAN junction connector |
K66-15 (CANL) - G45-16 (BAT) |
|||
K66-8 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Parking assist ECU*2 |
K66-18 (CANL) - G45-16 (BAT) |
|||
K66-9 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
Driving support ECU assembly |
K66-19 (CANL) - G45-16 (BAT) |
- *1: w/ Intelligent Clearance Sonar System
- *2: w/ Panoramic View Monitor System
Result | Proceed to |
|---|---|
OK |
A |
NG (Line to central gateway ECU (network gateway ECU)) |
B |
NG (Line to No. 1 CAN junction connector) |
C |
NG (Line to ECU or sensor) |
D |
| A | REPLACE NO. 7 CAN JUNCTION CONNECTOR |
| C | REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR) |
| D | GO TO STEP 5 |
|
CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
(a) Disconnect the G52 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Front view of wire harness connector (to No. 7 CAN Junction Connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
K66-1 (CANH) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
K66-11 (CANL) - G45-16 (BAT) |
| OK | REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |
| NG | REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 7 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
(a) Reconnect all wire harness connectors.
(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.
Click here ![]()
(c) Measure the resistance according to the value(s) in the table below.
*1 |
DLC3 |
- |
- |
*a |
Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
- |
- |
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G52-23 (CA1H) - G45-16 (BAT) |
Cable disconnected from negative (-) auxiliary battery terminal |
6 kΩ or higher |
G52-8 (CA1L) - G45-16 (BAT) |
HINT:
- If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
- If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.
| OK | REPLACE ECU OR SENSOR |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |



