Lin Communication System(for Gasoline Model)
Lost Communication with Power Source Control (B278C)
DESCRIPTION
This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and power management control ECU stops for 10 seconds or more.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B278C |
Lost Communication with Power Source Control |
An internal malfunction occurs in the certification ECU (smart key ECU assembly). |
Certification ECU (smart key ECU assembly) |
HINT:
The power management control ECU is built into the certification ECU (smart key ECU assembly).
NOTICE:
- Before replacing the certification ECU (smart key ECU assembly), refer to Registration.
Click here

- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs
|
CHECK FOR DTC
(a) Check for DTCs.
Body Electrical > Smart Key > Trouble CodesOK:
DTC B278C is not output.
| OK | USE SIMULATION METHOD TO CHECK |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
P/W Master Switch Communication Stop (B1206,B1273,B2321-B2324)
DESCRIPTION
This DTC is stored when LIN communication between the main body ECU (multiplex network body ECU) and multiplex network master switch assembly, sliding roof ECU (sliding roof drive gear assembly)*, power window regulator motor assembly (driver door), power window regulator motor assembly (front passenger door), power window regulator motor assembly (rear RH door) or power window regulator motor assembly (rear LH door) stops for 10 seconds or more.
- *: w/ Sliding Roof System
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B1206 |
P/W Master Switch Communication Stop |
No communication between multiplex network master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
B1273 |
Sliding Roof ECU Communication Stop |
No communication between sliding roof ECU (sliding roof drive gear assembly) and main body ECU (multiplex network body ECU) for 10 seconds or more.* |
|
B2321 |
D-Door Motor ECU Communication Stop |
No communication between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
B2322 |
P-Door Motor ECU Communication Stop |
No communication between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
B2323 |
RR-Door Motor ECU Communication Stop |
No communication between power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
B2324 |
RL-Door Motor ECU Communication Stop |
No communication between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more. |
|
- *: w/ Sliding Roof System
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click here

- When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*
Click here

- *: w/ Sliding Roof System
- Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
Click here

PROCEDURE
CLEAR DTC
(a) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs
|
CHECK FOR DTC
(a) Check for DTCs.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC is not output |
A |
DTC B1206, B1273*, B2321, B2322, B2323 and B2324 are output |
B |
DTC B1206, B2321, B2322, B2323 and B2324 are output |
C |
DTC B1206 and B2321 are output |
|
DTC B2322 and B2323 are output |
D |
Only DTC B1206 is output |
E |
Only DTC B1273 is output* |
F |
Only DTC B2321 is output |
G |
Only DTC B2322 is output |
H |
Only DTC B2323 is output |
I |
Only DTC B2324 is output |
J |
- *: w/ Sliding Roof System
| A | USE SIMULATION METHOD TO CHECK |
| C | GO TO STEP 4 |
| D | GO TO STEP 5 |
| E | GO TO STEP 6 |
| F | GO TO STEP 7 |
| G | GO TO STEP 10 |
| H | GO TO STEP 13 |
| I | GO TO STEP 15 |
| J | GO TO STEP 17 |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here ![]()
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
HINT:
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4D-17 or 4H-25 - MB-16 (LIN2) |
Always |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY)
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Disconnect the I16 multiplex network master switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - I16-17 (LIN1) |
Engine switch off |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Disconnect the I4 power window regulator motor assembly (front passenger door) connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - I4-9 (LIN) |
Engine switch off |
Below 1 Ω |
| OK | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
(a) Disconnect the I16 multiplex network master switch assembly connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I16-11 (B) - I16-12 (GND) |
Always |
11 to 14 V |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I16-12 (GND) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here ![]()
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
HINT:
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4D-17 - MB-16 (LIN2) |
Always |
Below 1 Ω |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
(a) Disconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4D-17 - O3-7 (MPX1) |
Engine switch off |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O3-1 (B) - O3-2 (E) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
O3-2 (E) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
INSPECT MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
(a) Remove the multiplex network master switch assembly. Click here |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
16 - 17 |
Always |
Below 1 Ω |
| NG | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
|
CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
(a) Disconnect the I20 power window regulator motor assembly (driver door) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I16-16 (LIN2) - I20-9 (LIN) |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I20-2 (B) - I20-1 (GND) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I20-1 (GND) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR))
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Disconnect the I4 power window regulator motor assembly (front passenger door) connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - I4-9 (LIN) |
Engine switch off |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I4-2 (B) - I4-1 (GND) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I4-1 (GND) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR))
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Disconnect the J9 power window regulator motor assembly (rear RH door) connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - J9-9 (LIN) |
Engine switch off |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
J9-2 (B) - J9-1 (GND) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
J9-1 (GND) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR))
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Disconnect the J10 power window regulator motor assembly (rear LH door) connector.
(c) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the engine switch from on (IG) to off and wait for 180 seconds or more without operating any switches.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - J10-9 (LIN) |
Engine switch off |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
J10-2 (B) - J10-1 (GND) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
J10-1 (GND) - Body ground |
Always |
Below 1 Ω |
| OK | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
LIN Communication Bus Malfunction (B2325)
DESCRIPTION
If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B2325 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B2325 |
LIN Communication Bus Malfunction |
The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more. |
|
- *: w/ Sliding Roof System
WIRING DIAGRAM
NOTICE:
- When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click here

- When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*
Click here

- *: w/ Sliding Roof System
- Before replacing the main body ECU (multiplex network body ECU), refer to Registration.
Click here

PROCEDURE
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
(a) Disconnect the J20 power window regulator motor assembly (driver door) connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 8 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output |
A |
DTC B2325 is not output |
B |
| B | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) |
|
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
(a) Disconnect the I16 multiplex network master switch assembly connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 10 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output |
A |
DTC B2325 is not output |
B |
| B | GO TO STEP 11 |
|
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
(a) Disconnect the I4 power window regulator motor assembly (front passenger door) connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 10 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output |
A |
DTC B2325 is not output |
B |
| B | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) |
|
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
(a) Disconnect the J9 power window regulator motor assembly (rear RH door) connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 10 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output |
A |
DTC B2325 is not output |
B |
| B | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) |
|
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
(a) Disconnect the J10 power window regulator motor assembly (rear LH door) connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 10 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output*1 |
A |
DTC B2325 is output*2 |
B |
DTC B2325 is not output |
C |
- *1: w/ Sliding Roof System
- *2: w/o Sliding Roof System
| B | GO TO STEP 7 |
| C | REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) |
|
CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
(a) Disconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Clear the DTCs.
Body Electrical > Main Body > Clear DTCs(c) After 10 seconds have elapsed, check if the DTC is output.
Body Electrical > Main Body > Trouble CodesResult | Proceed to |
|---|---|
DTC B2325 is output |
A |
DTC B2325 is not output |
B |
| A | GO TO STEP 7 |
| B | REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - EACH ECU)
(a) Disconnect the 4H instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - Body ground |
Always |
10 kΩ or higher |
(c) Disconnect all other connectors in the same circuit.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - Other terminals |
Always |
10 kΩ or higher |
Result | Proceed to |
|---|---|
OK*1 |
A |
OK*2 |
B |
NG |
C |
- *1: w/ Sliding Roof System
- *2: w/o Sliding Roof System
| B | GO TO STEP 10 |
| C | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY))
(a) Disconnect the 4D instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4D-17 - Body ground |
Always |
10 kΩ or higher |
4D-17 - Other terminals |
Always |
10 kΩ or higher |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
(a) Remove the instrument panel junction block assembly.
Click here ![]()
(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(c) Measure the resistance according to the value(s) in the table below.
HINT:
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
4H-25 - 4D-3 |
Always |
10 kΩ or higher |
MB-16 (LIN2) - Other terminals |
Always |
10 kΩ or higher |
| NG | REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
*b |
Waveform 1 |
(a) Using a Techstream, check the waveform.
HINT:
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
OK:
Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
4H-25 - Body ground |
Engine switch on (IG) |
2 V/DIV., 200 ms/DIV. |
Pulse generation (See waveform 1) |
4D-17 - Body ground* |
Engine switch on (IG) |
2 V/DIV., 200 ms/DIV. |
Pulse generation (See waveform 1) |
- *: w/ Sliding Roof System
| OK | USE SIMULATION METHOD TO CHECK |
| NG | REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR))
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
I16-16 (LIN2) - Body ground |
Always |
10 kΩ or higher |
I16-16 (LIN2) - Other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
Communication Malfunction between ECUs Connected by LIN (B2785)
DESCRIPTION
If the certification ECU (smart key ECU assembly) detects a communication error with an ECU connected to the certification bus lines for 7 seconds or more, DTC B2785 will be stored.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B2785 |
Communication Malfunction between ECUs Connected by LIN |
|
|
WIRING DIAGRAM
NOTICE:
- Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Registration.
Click here

- Before performing the inspection, check that DTC B2786 or B278C is not output.
Click here

- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
PROCEDURE
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs(c) After 7 seconds have elapsed, check if the DTC is output.
Body Electrical > Smart Key > Trouble CodesResult | Proceed to |
|---|---|
DTC B2785 is output |
A |
DTC B2785 is not output |
B |
| B | REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-13 (LIN) - Body ground |
Always |
10 kΩ or higher |
G40-13 (LIN) - Other terminals |
Always |
10 kΩ or higher |
| OK | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
No Response from Steering Lock ECU (B2786)
DESCRIPTION
This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator or upper bracket assembly) stops for 10 seconds or more.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
B2786 |
No Response from Steering Lock ECU |
No communication between steering lock ECU (steering lock actuator or upper bracket assembly) and certification ECU (smart key ECU assembly) for 10 seconds or more. |
|
WIRING DIAGRAM
NOTICE:
- Inspect the fuses for circuits related to this system before performing the following procedure.
- Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator or upper bracket assembly), refer to Registration.
Click here

- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
PROCEDURE
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY))
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G40-13 (LIN) - G43-5 (LIN) |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) - BATTERY AND BODY GROUND)
(a) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G43-7 (B) - G43-1 (GND) |
Always |
11 to 14 V |
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection | Condition | Specified Condition |
|---|---|---|
G43-1 (GND) - Body ground |
Always |
Below 1 Ω |
| NG | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Replace the steering lock ECU (steering lock actuator or upper bracket assembly).
for Manual Tilt and Manual Telescopic Steering Column: Click here ![]()
for Power Tilt and Power Telescopic Steering Column: Click here ![]()
|
REGISTER ECU CODE REGISTRATION
(a) Register the recognition codes in the ECUs.
HINT:
Refer to Registration.
Click here ![]()
|
CHECK FOR DTC
(a) Clear the DTCs.
Body Electrical > Smart Key > Clear DTCs(b) Recheck for DTCs.
Body Electrical > Smart Key > Trouble CodesOK:
DTC B2786 is not output.
| OK | END (STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) WAS DEFECTIVE) |
| NG | REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data ListTester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Communication D-Door Motor |
Connection status between power window regulator motor assembly (driver door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication P-Door Motor |
Connection status between power window regulator motor assembly (front passenger door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication RR-Door Motor |
Connection status between power window regulator motor assembly (rear RH door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication RL-Door Motor |
Connection status between power window regulator motor assembly (rear LH door) and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication Slide Roof |
Connection status between main body ECU (multiplex network body ECU) and sliding roof ECU (sliding roof drive gear assembly)*1 |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication Master SW |
Connection status between multiplex network master switch assembly and main body ECU (multiplex network body ECU) |
OK or STOP |
OK: Connected STOP: Not Connected |
DTC is output if an error occurs in LIN communication. |
Communication Sliding Sunshade ECU |
Connection status between roof sunshade ECU and main body ECU (multiplex network body ECU)*2 |
OK or STOP |
OK: Connected STOP: Not Connected |
Not applicable |
The Number of DTC |
Number of DTCs |
0 to 255 |
Number of stored DTCs |
- |
- *1: w/ Sliding Roof System
- *2: Although the item is displayed on the Techstream, it is not applicable to this vehicle.
Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
# Codes |
Number of DTCs |
0 to 255 |
Number of stored DTCs |
- |
Diagnosis System
DIAGNOSIS SYSTEM
DESCRIPTION
The main body ECU (multiplex network body ECU) and certification ECU (smart key ECU assembly) control the LIN communication system. LIN communication system data and Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3).
When the system seems to be malfunctioning, use the Techstream to check for malfunctions and perform repairs.
CHECK DLC3
(a) Check the DLC3.
Click here ![]()
INSPECT BATTERY VOLTAGE
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery.
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
LIN Communication System (for Gasoline Model)DTC No. | Detection Item | Link |
|---|---|---|
B1206 |
P/W Master Switch Communication Stop |
|
B1273 |
Sliding Roof ECU Communication Stop |
|
B2321 |
D-Door Motor ECU Communication Stop |
|
B2322 |
P-Door Motor ECU Communication Stop |
|
B2323 |
RR-Door Motor ECU Communication Stop |
|
B2324 |
RL-Door Motor ECU Communication Stop |
|
B2325 |
LIN Communication Bus Malfunction |
|
B2785 |
Communication Malfunction between ECUs Connected by LIN |
|
B2786 |
No Response from Steering Lock ECU |
|
B278C |
Lost Communication with Power Source Control |
Dtc Check / Clear
DTC CHECK / CLEAR
CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Key / Trouble Codes.
Body Electrical > Main Body > Trouble Codes Body Electrical > Smart Key > Trouble Codes(e) Check the details of the DTCs.
Click here ![]()
CLEAR DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Main Body or Smart Key / Trouble Codes.
Body Electrical > Main Body > Clear DTCs Body Electrical > Smart Key > Clear DTCs(e) Clear the DTCs.
How To Proceed With Troubleshooting
HINT:
- Use the following procedure to troubleshoot the LIN communication system.
- *: Use the Techstream.
PROCEDURE
VEHICLE BROUGHT TO WORKSHOP
|
CUSTOMER PROBLEM ANALYSIS
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points for problem analysis:
What |
Vehicle model, system name |
When |
Date, time, occurrence frequency |
Where |
Road conditions |
Under what conditions? |
Driving conditions, weather conditions |
How did it happen? |
Problem symptoms |
|
PRE-CHECK
(a) Measure the battery voltage.
Standard Voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
(b) Check the fuses and relays.
(c) Check the connectors and terminals to make sure that there are no abnormalities such as a loose connection or deformation.
|
INSPECT COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
(a) Using the Techstream, check for CAN communication system DTCs.
Click here ![]()
Result | Proceed to |
|---|---|
CAN DTCs are not output |
A |
CAN DTCs are output |
B |
| B | GO TO CAN COMMUNICATION SYSTEM |
|
INSPECT COMMUNICATION FUNCTION OF LIN COMMUNICATION SYSTEM*
(a) Using the Techstream, check for LIN communication system DTCs.
Click here ![]()
Result | Proceed to |
|---|---|
LIN DTCs are not output |
A |
LIN DTCs are output |
B |
| B | GO TO DIAGNOSTIC TROUBLE CODE CHART |
|
OVERALL ANALYSIS AND TROUBLESHOOTING*
(a) Terminals of ECU
Click here ![]()
(b) Data List / Active Test
Click here ![]()
|
REPAIR OR REPLACE
|
CONFIRMATION TEST
| NEXT | END |
Parts Location
PARTS LOCATION
ILLUSTRATION
*A |
w/ Sliding Roof System |
*B |
for Manual Tilt and Manual Telescopic Steering Column |
*C |
for Power Tilt and Power Telescopic Steering Column |
- |
- |
*1 |
MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |
*2 |
INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - ECU-B NO. 2 FUSE - DOOR F/L FUSE - DOOR F/R FUSE - DOOR R/L FUSE - DOOR R/R FUSE - STRG LOCK FUSE |
*3 |
S/ROOF FUSE |
*4 |
CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
*5 |
STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) |
*6 |
MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |
*7 |
DLC3 |
- |
- |
ILLUSTRATION
*A |
w/ Sliding Roof System |
- |
- |
*1 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR) |
*2 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR) |
*3 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR) |
*4 |
POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR) |
*5 |
SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) |
- |
- |
Precaution
PRECAUTION
PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize the following systems after the cable is reconnected.
System Name | See Procedure |
|---|---|
Lane Departure Alert System (w/ Steering Control) |
|
Intelligent Clearance Sonar System |
|
Parking Assist Monitor System |
|
Panoramic View Monitor System |
|
Pre-collision System |
|
Lighting System (for Gasoline Model with Cornering Light) |
System Description
SYSTEM DESCRIPTION
LIN COMMUNICATION SYSTEM DESCRIPTION
The LIN communication system is used for communication between the components in the tables below. If communication cannot be performed through LIN communication such as when there is an open or short in a communication line, the master control ECU of the relevant system will store a DTC. Refer to the table below about the communication bus lines and connected components.
HINT:
- Each component has a fail-safe function which operates in the event of a malfunction to protect the system and allow communication between other components to continue.
- In the following table, "○" indicates that the function applies, and "-" indicates that it does not.
Component | Master Control | LIN Communication DTC Output Function |
|---|---|---|
Main Body ECU (Multiplex Network Body ECU) |
○ |
○ |
Power Window Regulator Motor Assembly (Driver Door) |
- |
- |
Power Window Regulator Motor Assembly (Front Passenger Door) |
- |
- |
Power Window Regulator Motor Assembly (Rear LH Door) |
- |
- |
Power Window Regulator Motor Assembly (Rear RH Door) |
- |
- |
Multiplex Network Master Switch Assembly |
- |
- |
Sliding Roof ECU (Sliding Roof Drive Gear Assembly)* |
- |
- |
- *: w/ Sliding Roof System
Component | Master Control | LIN Communication DTC Output Function |
|---|---|---|
Certification ECU (Smart Key ECU Assembly) |
○ |
○ |
Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly) |
- |
- |
System Diagram
SYSTEM DIAGRAM
DOOR BUS LINES
CERTIFICATION BUS LINES

Terminals Of Ecu
TERMINALS OF ECU
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
(a) Disconnect the MB main body ECU (multiplex network body ECU) connector.
Click here ![]()
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connectors disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
MB-11 (GND1) - Body ground |
- |
Ground |
Always |
Below 1 Ω |
MB-31 (BECU) - Body ground |
- |
Battery power supply |
Always |
11 to 14 V |
MB-30 (ACC) - Body ground |
- |
ACC power supply |
Engine switch on (ACC) |
11 to 14 V |
Engine switch off |
Below 1 V |
|||
MB-32 (IG) - Body ground |
- |
IG power supply |
Engine switch on (IG) |
11 to 14 V |
Engine switch off |
Below 1 V |
(c) Reconnect the MB main body ECU (multiplex network body ECU) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
4H-25 - Body ground |
LA-BE - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
4D-17 - Body ground* |
L - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
- *: w/ Sliding Roof System
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)
(a) Disconnect the I20 power window regulator motor assembly (driver door) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I20-2 (B) - Body ground |
GR - Body ground |
Battery power supply |
Always |
11 to 14 V |
I20-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the I20 power window regulator motor assembly (driver door) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I20-9 (LIN) - Body ground |
G - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)
(a) Disconnect the I4 power window regulator motor assembly (front passenger door) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I4-2 (B) - Body ground |
GR - Body ground |
Battery power supply |
Always |
11 to 14 V |
I4-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the I4 power window regulator motor assembly (front passenger door) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I4-9 (LIN) - Body ground |
P - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)
(a) Disconnect the J9 power window regulator motor assembly (rear RH door) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J9-2 (B) - Body ground |
B - Body ground |
Battery power supply |
Always |
11 to 14 V |
J9-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the J9 power window regulator motor assembly (rear RH door) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J9-9 (LIN) - Body ground |
P - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)
(a) Disconnect the J10 power window regulator motor assembly (rear LH door) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J10-2 (B) - Body ground |
B - Body ground |
Battery power supply |
Always |
11 to 14 V |
J10-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the J10 power window regulator motor assembly (rear LH door) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
J10-9 (LIN) - Body ground |
P - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
(a) Disconnect the I16 multiplex network master switch assembly connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I16-11 (B) - Body ground |
LA-R - Body ground |
Battery power supply |
Always |
11 to 14 V |
I16-12 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the I16 multiplex network master switch assembly connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
I16-17 (LIN1) - Body ground |
P - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
I16-16 (LIN2) - Body ground |
G - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Sliding Roof System)
(a) Disconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
O3-1 (B) - Body ground |
B - Body ground |
Battery power supply |
Always |
11 to 14 V |
O3-2 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the O3 sliding roof ECU (sliding roof drive gear assembly) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
O3-7 (MPX1) - Body ground |
LA-P - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
(a) Disconnect the G40 certification ECU (smart key ECU assembly) connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
HINT:
Measure the values on the wire harness side with the connector disconnected.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G40-18 (E) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
G40-4 (+B) - Body ground |
W - Body ground |
Battery power supply |
Always |
11 to 14 V |
(c) Reconnect the G40 certification ECU (smart key ECU assembly) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G40-13 (LIN) - Body ground |
B - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |
CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)
(a) Disconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(b) Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G43-1 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
G43-7 (B) - Body ground |
W - Body ground |
Battery power supply |
Always |
11 to 14 V |
(c) Reconnect the G43 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
(d) Check for pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
G43-5 (LIN) - Body ground |
B - Body ground |
LIN communication line |
Engine switch on (IG) |
Pulse generation |


