Seats

ECU Terminals

~5min read

ECU TERMINALS

INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY (TMMT Made)

(a) Disconnect the connector from the air conditioning amplifier assembly.

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F72-5 (IG+) - Body ground

B - Body ground

IG power supply

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

F72-29 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

F72-1 (B) - Body ground

V - Body ground

Battery power supply

Always

11 à 14 V

(c) Reconnect the air conditioning amplifier assembly connector.

(d) Check that pulses are generated according to the values shown in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F72-3 (LIN1) - Body ground

L - Body ground

Seat heater switch signal

Ignition Switch in ON position

Pulse generation

INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY (TMC Made)

(a) Disconnect the connector from the air conditioning amplifier assembly.

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F139-2 (IG+) - Body ground

B - Body ground

IG power supply

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

F139-4 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

F139-1 (B) - Body ground

V - Body ground

Battery power supply

Always

11 à 14 V

(c) Reconnect the air conditioning amplifier assembly connector.

(d) Check that pulses are generated according to the values shown in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F139-14 (LIN1) - Body ground

BE - Body ground

Seat heater switch signal

Ignition Switch in ON position

Pulse generation

CHECK AIR CONDITIONING CONTROL ASSY

(a) Disconnect the air conditioning control assembly connector.

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F61-16 (GND) - Body Ground

W-B - Body ground

Ground

Always

Below 1 Ω

F61-10 (IG+) - F61-16 (GND)

BE - W-B

IG power supply

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

(c) Reconnect the air conditioning control assembly connector.

(d) Measure the voltage according to the value(s) specified in the table below.

(e) Check that pulses are generated according to the values shown in the table below.

Tester Connection

Wire Color

Terminal Description

Condition

Specified Condition

F61-2 (LIN1) - F61-16 (GND)

L - W-B

Seat heater switch signal

Ignition Switch in ON position

Pulse generation

F61-4 (RV) - F61-16 (GND)

SB - W-B

Seat heater switch volume signal

Ignition switch ON, front passenger seat heater switch OFF

Below 0.6 V

Ignition switch ON, front passenger seat heater switch HI

3,9 à 5,5 V

Ignition switch ON, front passenger seat heater switch MID

3,4 à 4,7 V

Ignition switch ON, front passenger seat heater switch LO

2,5 à 3,5 V

F61-11 (SW) - F61-16 (GND)

R - W-B

Seat heater switch volume signal

Ignition switch ON, front passenger seat heater switch OFF

Below 1 V

Ignition switch ON, front passenger seat heater switch ON

11 à 14 V

F61-6 (RV) - F61-16 (GND)

LG - W-B

Seat heater switch volume signal

Ignition switch ON, driver seat heater switch OFF

Below 0.6 V

Ignition switch ON, driver seat heater switch HI

3,9 à 5,5 V

Ignition switch ON, driver seat heater switch MID

3,4 à 4,7 V

Ignition switch ON, driver seat heater switch LO

2,5 à 3,5 V

F61-12 (SW) - F61-16 (GND)

P - W-B

Seat heater switch volume signal

Ignition switch ON, driver seat heater switch OFF

Below 1 V

Ignition switch ON, driver seat heater switch ON

11 à 14 V