Seats

Front seat heater on left side does not operate

~9min read

DESCRIPTION

When the seat heater switch on the air conditioning control assembly is operated, the left seat heater control sub-assembly receives the signal. The left seat heater control sub-assembly receives the signal and operates the front seat heater.

WIRING DIAGRAM

TMC manufactured

TMMT manufactured

PRECAUTION / NOTICE / HINT

NOTICE:

  • If the battery voltage is low, the seat heater system may not operate. Refer to the Data List for the seat heater system.

    Click here

  • Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Body Electrical > Air Conditioner > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Check the DTCs.

Click here

Body Electrical > Air Conditioner > Trouble Codes

OK:

DTC B14B5 is not output.

Result:

Result

Proceed to

OK (Manufactured by TMC)

A

OK (Manufactured by TMMT)

B

NG

C

B

GO TO STEP 12

C

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. INSPECT WIRE HARNESS AND CONNECTOR (IG POWER SOURCE - LEFT SEAT HEATER CONTROL SUB-ASSEMBLY)

(a) Disconnect the left seat heater control sub-assembly connector.

*a

Front view of wire harness side connector

(to Left Seat Heater Control Sub-assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

Z2-1 (+B1) - Body ground

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (LEFT SEAT HEATER CONTROL SUB-ASSEMBLY - LEFT FRONT SEAT HEATER CUSHION ASSEMBLY - BODY GROUND)

(a) Disconnect the Z2 connector from the left seat heater control sub-assembly.

(b) Disconnect the connector from the front left seat cushion heater assembly Z1.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Z2-7 (HTR1) - Z1-1

Always

Below 1 Ω

Z2-9 (THR+) - Z1-4

Always

Below 1 Ω

Z2-5 (THR-) - Z1-5

Always

Below 1 Ω

Z2-10 (E) - Z1-6

Always

Below 1 Ω

Z1-2 - Body ground

Always

Below 1 Ω

Z2-7 (HTR1) or Z1-1 - Body ground

Always

10 kΩ minimum

Z2-9 (THR+) or Z1-4 - Body ground

Always

10 kΩ minimum

Z2-5 (THR-) or Z1-5 - Body ground

Always

10 kΩ minimum

Z2-10 (E) or Z1-6 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT FRONT LEFT SEAT CUSHION HEATER ASSEMBLY

(a) Remove the front left seat cushion heater assembly.

Click here

(b) Inspect the front left seat cushion heater assembly.

Click here

NG

REPLACE FRONT LEFT SEAT CUSHION HEATER ASSEMBLY

OK
  1. INSPECT FRONT LEFT SEAT BACK HEATER ASSEMBLY

(a) Remove the front left seat back heater assembly.

Click here

(b) Inspect the front left seat back heater assembly.

Click here

NG

REPLACE FRONT LEFT SEAT BACK HEATER ASSEMBLY

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - LEFT SEAT HEATER CONTROL SUB-ASSEMBLY)

(a) Disconnect the F61 seat heater switch (air conditioning control assembly) connector.

(b) Disconnect the Z2 connector from the left seat heater control sub-assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F61-12 (SW) - Z2-2 (SWR)

Always

Below 1 Ω

F61-6 (RV) - Z2-3 (VOL)

Always

Below 1 Ω

F61-12 (SW) or Z2-2 (SWR) - Body ground

Always

10 kΩ minimum

F61-6 (RV) or Z2-3 (VOL) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE LEFT SEAT HEATER CONTROL SUB-ASSEMBLY

(a) Temporarily replace the left heater control sub-assembly with a new or known-good one.

Click here

NEXT
  1. CHECK OPERATION OF SEAT HEATER SYSTEM

(a) Confirm that the seat heater system operates normally.

OK:

The seat heater system operates normally.

OK

END (LEFT SEAT HEATER CONTROL SUB-ASSEMBLY WAS DEFECTIVE)

NG
  1. REPLACE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)

(a) Temporarily replace the seat heater switch (air conditioning control assembly) with a new or normally functioning one.

Click here

NEXT
  1. CHECK OPERATION OF SEAT HEATER SYSTEM

(a) Confirm that the seat heater system operates normally.

OK:

The seat heater system operates normally.

OK

END (THE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) WAS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

  1. INSPECT WIRE HARNESS AND CONNECTOR (IG POWER SOURCE - LEFT SEAT HEATER CONTROL SUB-ASSEMBLY)

(a) Disconnect the left seat heater control sub-assembly connector.

*a

Front view of wire harness side connector

(to Left Seat Heater Control Sub-assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

Z2-8 (+B1) - Body ground

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (LEFT SEAT HEATER CONTROL SUB-ASSEMBLY - LEFT FRONT SEAT HEATER CUSHION ASSEMBLY - BODY GROUND)

(a) Disconnect the Z2 connector from the left seat heater control sub-assembly.

(b) Disconnect the connector from the front left seat cushion heater assembly Z1.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

Z2-1 (HTR1) - Z1-1

Always

Below 1 Ω

Z2-6 (THR+) - Z1-4

Always

Below 1 Ω

Z2-11 (THR-) - Z1-5

Always

Below 1 Ω

Z2-7 (E) - Z1-6

Always

Below 1 Ω

Z1-2 - Body ground

Always

Below 1 Ω

Z2-1 (HTR1) or Z1-1 - Body ground

Always

10 kΩ minimum

Z2-6 (THR+) or Z1-4 - Body ground

Always

10 kΩ minimum

Z2-11 (THR-) or Z1-5 - Body ground

Always

10 kΩ minimum

Z2-7 (E) or Z1-6 - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT FRONT LEFT SEAT CUSHION HEATER ASSEMBLY

(a) Remove the front left seat cushion heater assembly.

Click here

(b) Inspect the front left seat cushion heater assembly.

Click here

NG

REPLACE FRONT LEFT SEAT CUSHION HEATER ASSEMBLY

OK
  1. INSPECT FRONT LEFT SEAT BACK HEATER ASSEMBLY

(a) Remove the front left seat back heater assembly.

Click here

(b) Inspect the front left seat back heater assembly.

Click here

NG

REPLACE FRONT LEFT SEAT BACK HEATER ASSEMBLY

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) - LEFT SEAT HEATER CONTROL SUB-ASSEMBLY)

(a) Disconnect the F61 seat heater switch (air conditioning control assembly) connector.

(b) Disconnect the Z2 connector from the left seat heater control sub-assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F61-12 (SW) - Z2-3 (SWR)

Always

Below 1 Ω

F61-6 (RV) - Z2-4 (VOL)

Always

Below 1 Ω

F61-12 (SW) or Z2-3 (SWR) - Body ground

Always

10 kΩ minimum

F61-6 (RV) or Z2-4 (VOL) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. REPLACE LEFT SEAT HEATER CONTROL SUB-ASSEMBLY

(a) Temporarily replace the left heater control sub-assembly with a new or known-good one.

Click here

NEXT
  1. CHECK OPERATION OF SEAT HEATER SYSTEM

(a) Confirm that the seat heater system operates normally.

OK:

The seat heater system operates normally.

OK

END (LEFT SEAT HEATER CONTROL SUB-ASSEMBLY WAS DEFECTIVE)

NG
  1. REPLACE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY)

(a) Temporarily replace the seat heater switch (air conditioning control assembly) with a new or normally functioning one.

Click here

NEXT
  1. CHECK OPERATION OF SEAT HEATER SYSTEM

(a) Confirm that the seat heater system operates normally.

OK:

The seat heater system operates normally.

OK

END (THE SEAT HEATER SWITCH (AIR CONDITIONING CONTROL ASSEMBLY) WAS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY