Removal
REMOVAL
PRECAUTION / NOTICE / HINT
NOTICE:
Be sure to hold the front wiper arm up. Lifting the front wiper arm by the wiper blade may damage or deform the front wiper blade.
PROCEDURE
1. REMOVE FRONT WIPER ARM CAP
(a) Using a screwdriver with its tip wrapped in protective tape, release the claws to remove the front wiper arm cap as shown in the illustration.
*a |
Protective tape |
![]() |
Remove in this direction |
HINT:
Repeat the same procedure for the right side and the left side.
2. REMOVE LH FRONT WIPER ARM AND BLADE ASSEMBLY
(a) Remove the nut and LH front wiper arm and blade assembly. |
![]() |
3. REMOVE RH FRONT WIPER ARM AND BLADE ASSEMBLY
(a) Remove the nut and RH front wiper arm and blade assembly. |
![]() |
4. REMOVE LH WINDSHIELD OUTER MOULDING
(a) Release the claws and clip to remove the LH windshield outer moulding as shown in the illustration.
![]() |
Remove in this direction |
5. REMOVE RH WINDSHIELD OUTER MOULDING
HINT:
Perform the same procedure as for the left side.
6. REMOVE COWL TOP VENTILATOR GRILLE SUB-ASSEMBLY
NOTICE:
To prevent damage to the windshield glass, remove any foreign matter (sand, dust, etc.) around the contact surfaces of the cowl top ventilator grille sub-assembly and the windshield glass.
(a) Remove the 2 clips.
(b) Close the hood sub-assembly.
(c) Insert the moulding remover to the starting position, pushing it as far as possible as shown in the illustration.
*a |
Starting position: Cowl top ventilator grille sub-assembly and moulding remover side aligned |
*b |
Inserted as far as possible |
*c |
Not inserted to the starting position |
*d |
Not fully inserted |
*e |
Not inserted straight |
*f |
Cloth or equivalent |
NOTICE:
- To prevent damage to the windshield glass, place a piece of cloth between the moulding remover and the windshield glass.
- Be sure to insert the moulding remover fully, as far as possible. Otherwise, the cowl top ventilator grille sub-assembly may be deformed or damaged.
HINT:
If it is difficult to insert the moulding remover, lift the cowl top ventilator grille sub-assembly slightly.
(d) While pushing the moulding remover in the direction indicated by arrow (A), press the moulding remover in the direction indicated by arrow (B) to release the cowl top ventilator grille sub-assembly.
![]() |
Push in this direction (A) |
![]() |
Push in this direction (B) |
NOTICE:
- Be sure to repeat the procedure to release the entire cowl top ventilator grille sub-assembly.
- Be sure to perform the procedure while pushing the moulding remover in the direction indicated by arrow (A). Otherwise, the cowl top ventilator grille sub-assembly may be deformed or damaged.
- Be careful not to pry on the cowl top ventilator grille sub-assembly more than necessary to release it. Otherwise, it may be deformed or damaged.
*a
Pried until released
*b
Excessive prying
(e) Using a moulding remover, pry the cowl top ventilator grille sub-assembly repeatedly while gradually moving the moulding remover by half its width toward the center of the vehicle, and repeat the procedure on the other side of the vehicle as shown in the illustration to release the cowl top ventilator grille sub-assembly from the windshield glass.
*a |
Half the width of the moulding remover |
- |
- |
![]() |
Removal order |
- |
- |
NOTICE:
- Be sure to move the moulding remover by only half its width after prying on the cowl top ventilator grille sub-assembly. Otherwise, the cowl top ventilator grille sub-assembly may be damaged or deformed.
- Be careful not to lift or pull the front cowl top ventilator grille sub-assembly by hand until it is completely released. Otherwise, it may be deformed or damaged.
(f) Open the hood sub-assembly.
(g) Release the guides to remove the cowl top ventilator grille sub-assembly as shown in the illustration.
![]() |
Remove in this direction |
- |
- |
NOTICE:
The cowl top ventilator grille sub-assembly may contact the brake master cylinder reservoir filler cap assembly during removal and cause the cap assembly to fall. Check the installation condition of the brake master cylinder reservoir filler cap assembly after removing the cowl top ventilator grille sub-assembly.
7. REMOVE FRONT WIPER MOTOR AND LINK ASSEMBLY
(a) for USA and Canada:
(1) Remove the 2 bolts.
(2) Release the motor grommet as shown in the illustration. NOTICE: Be careful not to damage the windshield when removing the front wiper motor and link assembly. |
|
(3) Disconnect the connector to remove the front wiper motor and link assembly. |
![]() |
(b) except USA and Canada:
(1) Remove the 2 bolts. |
![]() |
(2) Release the motor grommet as shown in the illustration. NOTICE: Be careful not to damage the windshield when removing the front wiper motor and link assembly. |
|
(3) Disconnect the connector to remove the front wiper motor and link assembly. |
![]() |
8. REMOVE FRONT WIPER LINK SUB-ASSEMBLY (for USA and Canada)
(a) Using a screwdriver with its tip wrapped in protective tape, disconnect the No. 1 front wiper link rod from the front wiper motor assembly pivot as shown in the illustration. |
|
(b) Scribe alignment marks on the front wiper lever subassembly and the front wiper linkage assembly. |
|
(c) Remove the nut and the front wiper link subassembly.
9. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
(a) for USA and Canada: (1) Remove the 3 bolts and the front windshield wiper motor assembly. |
![]() |
(b) except USA and Canada:
(1) Using a screwdriver with its tip wrapped in protective tape, separate the No. 1 front wiper linkage rod from the pivot of the front windshield wiper motor assembly, as shown in the illustration. |
|
(2) Remove the 3 bolts. |
![]() |
(3) Move the front windshield wiper motor assembly in the direction indicated by arrow (1), then pull the front windshield wiper motor assembly in the direction indicated by arrow (2) in the illustration to remove it from the front wiper linkage assembly.
![]() |
Remove in this direction (1) |
![]() |
Remove in this direction (2) |
.png)


.png)
.png)









