Installation
INSTALLATION
PRECAUTION / NOTICE / HINT
NOTICE:
Be sure to hold the front wiper arm up. Lifting the front wiper arm by the wiper blade may damage or deform the front wiper blade.
PROCEDURE
1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY
(a) for USA and Canada:
(1) Install the front windshield wiper motor assembly with the 3 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
![]() |
Install in this direction (1) |
![]() |
Install in this direction (2) |
(b) except USA and Canada:
(1) Push the front windshield wiper motor assembly in the direction indicated by arrow (1), then move the front windshield wiper motor assembly in the direction indicated by arrow (2) in the illustration to temporarily place it on the front wiper linkage assembly.
(2) Install the front windshield wiper motor assembly with the 3 bolts.
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
(3) Apply MP grease to the pivot of the front windshield wiper motor assembly.
![]() |
MP grease |
(4) Connect the No. 1 front wiper linkage rod to the pivot of the front windshield wiper motor assembly. |
|
2. INSTALL FRONT WINDSHIELD WIPER LINK SUBASSEMBLY (for USA and Canada)
(a) When replacing the front windshield wiper link subassembly with a new one:
(1) Temporarily place the front windshield wiper link subassembly on the front windshield wiper motor assembly using the nut. |
![]() |
(2) Temporarily install the front wiper motor and linkage onto the link pivot of the front windshield wiper link subassembly. |
![]() |
(3) Align the front link subassembly with the front wiper motor and linkage as shown in the illustration.
(4) Tighten the nut to install the front windshield wiper lever subassembly.
Torque:
17.2 N·m {175 kgf·cm, 13 ft·lbf}
(b) When reusing the front windshield wiper link subassembly:
(1) Align the alignment marks to install the front windshield wiper lever subassembly with the nut. Torque: 17.2 N·m {175 kgf·cm, 13 ft·lbf} |
|
(2) Apply MP grease to the link pivot of the front windshield wiper link subassembly.
![]() |
MP grease |
(3) Connect the front windshield wiper linkage assembly rod to the link pivot of the front windshield wiper link subassembly. |
![]() |
3. INSTALL FRONT WINDSHIELD WIPER MOTOR AND LINKAGE ASSEMBLY
(a) for USA and Canada:
(1) Connect the connector.
(2) Engage the motor grommet as shown in the illustration. NOTICE: Take care not to damage the windshield glass when installing the front windshield wiper motor and linkage assembly. Torque: 5.5 N·m {56 kgf·cm, 49 in·lbf} |
|
(b) except USA and Canada:
(1) Connect the connector.
(2) Engage the motor grommet as shown in the illustration. NOTICE: Take care not to damage the windshield glass when installing the front windshield wiper motor and linkage assembly. |
|
(3) Install the windshield wiper motor and linkage assembly with the 2 bolts.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
4. INSTALL COWL TOP VENTILATOR GRILLE SUBASSEMBLY
(a) Engage the guides as shown in the illustration.
![]() |
Install in this direction |
- |
- |
NOTICE:
The cowl top ventilator grille subassembly may contact the brake master cylinder reservoir filler cap assembly during installation and cause the cap assembly to fall. Check the installation condition of the brake master cylinder reservoir filler cap assembly after installing the cowl top ventilator grille subassembly.
(b) Engage the guides to install the cowl top ventilator grille subassembly as shown in the illustration.
![]() |
Install in this direction |
- |
- |
(c) Install the 2 clips.
5. INSTALL LEFT WINDSHIELD OUTER MOLDING
(a) Engage the claws to install the clip and the left windshield outer molding as shown in the illustration.
![]() |
Install in this direction |
6. INSTALL RIGHT WINDSHIELD OUTER MOLDING
HINT:
Perform the same procedure as for the left side.
7. INSTALL RIGHT FRONT WINDSHIELD WIPER ARM AND BLADE ASSEMBLY
(a) When reusing the right front windshield wiper arm and blade assembly:
(1) Clean the wiper arm splines to remove burrs, dust, etc. NOTICE: Do not grind the wiper arm splines. |
|
(b) When reusing the front windshield wiper motor and linkage assembly:
(1) Clean the wiper pivot splines with a wire brush.
(c) Turn the ignition switch to ON.
(d) Operate the front windshield wiper motor assembly, then stop the front windshield wiper motor and linkage assembly at the automatic stop position.
(e) Turn the ignition switch to OFF.
(f) Install the right front windshield wiper arm and blade assembly with the nut in the position shown in the illustration. Torque: 26 N·m {265 kgf·cm, 19 ft·lbf} HINT: Hold the wiper arm by hand while tightening the nut. Reference measurement:
|
|
8. INSTALL LEFT FRONT WINDSHIELD WIPER ARM AND BLADE ASSEMBLY
(a) When reusing the left front windshield wiper arm and blade assembly:
(1) Clean the wiper arm splines to remove burrs, dust, etc. NOTICE: Do not grind the wiper arm splines. |
|
(b) When reusing the front windshield wiper motor and linkage assembly:
(1) Clean the wiper pivot splines with a wire brush.
(c) Install the left front windshield wiper arm and blade assembly with the nut in the position shown in the illustration. Torque: 26 N·m {265 kgf·cm, 19 ft·lbf} HINT: Hold the wiper arm by hand while tightening the nut. Reference measurement:
|
|
(d) Turn the ignition switch to the ON position.
(e) Operate the front wipers while spraying windshield washer fluid onto the windshield glass. Make sure the front wipers operate properly and do not contact the vehicle body.
(f) Turn the ignition switch to the OFF position.
(g) Raise each wiper arm twice after the wipers have stopped, then check the wiper stop position.
9. INSTALL FRONT WIPER ARM CAP
(a) Engage the claws to install the front wiper arm cap, as shown in the illustration.
![]() |
Install in this direction |
HINT:
Repeat the same procedure for the right side and the left side.
.png)
.png)
.png)



.png)





