Exterior Panels / Trim

Removal

~6min read

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration) that must be performed after the parts have been removed and installed, or replaced during removal/installation of the front door glass moulding, are shown below.

Procedure Required After Replacing / Removing / Installing Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative Function When Required Procedure Is Not Performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Front door power window regulator assembly
  • Front door glass sub-assembly
  • Front door glass run

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

CAUTION:

Be sure to read the Precautions carefully before performing maintenance.

Click here

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

Click here

3. REMOVE FRONT DOOR OUTER MOULDING SUB-ASSEMBLY

HINT:

When removing the front door outer moulding sub-assembly, heat the vehicle body and the front door outer moulding sub-assembly using a heat light.

Heating Temperature

Item

Temperature

Vehicle Body

40 à 60 °C

Front door outer moulding sub-assembly

20 à 30 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body or the moulding.

(a) Using a heat light, heat the front door outer moulding sub-assembly.

(b) Apply protective tape around the front door outer moulding sub-assembly as shown in the illustration.

*a

Double-sided adhesive tape

Remove in this direction (1)

Remove in this direction (2)

Protective tape

(c) Using a D-type moulding remover, release the clip and guide, and remove the double-sided tape and sponge seal to remove the front door outer moulding sub-assembly, as shown in the illustration.

4. DETACH FRONT DOOR WEATHERSTRIP

(a) Using a clip remover, release the clips to detach the front door weatherstrip.

5. REMOVE UPPER DOOR FRAME GARNISH

Click here

6. REMOVE FRONT DOOR GLASS RUN

Click here

7. REMOVE FRONT DOOR LOWER FRAME SUB-ASSEMBLY

Click here

8. REMOVE FRONT DOOR FIXED GLASS

Click here

9. REMOVE FRONT DOOR UPPER GLASS MOULDING

(a) Install a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Wrap tape around the 4.0 mm (0.157 in.) drill bit at 5.0 mm (0.197 in.) from the tip, as shown in the illustration.

Standard measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

This tape on the 4.0 mm (0.157 in.) drill bit prevents it from drilling too deep.

*a

Tape

(c) Lightly press the drill against the rivets to drill out the rivet heads, and remove the 6 rivets.

CAUTION:

Caution: Drilled rivets may be hot. Handle with care.

NOTICE:

  • Excessive pressure on the drill will cause the rivet to spin and not be drilled.
  • Prying on the rivets with the drill may damage the rivet holes or the drill bit.

(d) Using a vacuum cleaner, remove rivet fragments and chips from the drilled areas.

(e) Release the guide to remove the front door upper glass moulding from the door frame.

10. REMOVE FRONT DOOR SCUFF PLATE

Click here

11. REMOVE COWL SIDE TRIM PANEL

Click here

12. REMOVE FRONT DOOR GLASS FRONT MOULDING

(a) Disconnect each connector.

(b) Release each clip.

(c) Remove the 5 bolts and the front door panel sub-assembly.

NOTICE:

To prevent damage, when removing the front door panel sub-assembly, make sure there are enough people to hold it properly.

(d) Install a 4.0 mm (0.157 in.) drill bit into a drill.

(e) Wrap tape around the 4.0 mm (0.157 in.) to 5.0 mm (0.197 in.) drill bit from the tip as shown in the illustration.

Standard measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

This tape on the 4.0 mm (0.157 in.) drill bit prevents it from drilling too deep.

*a

Tape

(f) Lightly press the drill against the rivets to drill out the rivet heads, and remove the 2 rivets and the front door glass front moulding.

CAUTION:

Caution: Drilled rivets may be hot. Handle with care.

NOTICE:

  • Excessive pressure on the drill will cause the rivet to spin and not be drilled.
  • Prying on the rivets with the drill may damage the rivet holes or the drill bit.

(g) Using a vacuum cleaner, remove rivet fragments and chips from the drilled areas.