Exterior Panels / Trim

Removal

~6min read

REMOVAL

PRECAUTION / NOTICE / HINT

The procedures required (adjustment, calibration, initialization or registration), which must be performed once the parts have been removed and installed, or replaced when removing/installing the masking tape, are indicated below.

Procedure Required After Replacing / Removing / Installing Parts

Replaced Part or Performed Procedure

Required Procedure

Effect/Inoperative Function When Required Procedure Is Not Performed

Link

Disconnect the cable from the negative (-) battery terminal.

Initialize Back Door Lock

Door Lock Control System

Memorize Steering Angle Neutral Point

Lane Departure Alert System (with Steering Control)

Pre-Collision System

  • Front door power window regulator assembly
  • Front door glass sub-assembly
  • Front door glass run

Initialize Power Window Control System

  • Automatic Open and Close Function
  • Anti-Pinch Function
  • Anti-Pinch Function Operation
  • Remote Control Function
  • Key-Linked Function
  • Function Linked to Remote Control Transmitter
  • Keyless Operation
  • Power Window Open Warning Function

HINT:

  • Repeat the same procedure for the right side and the left side.
  • The following procedure applies to the left side.

PROCEDURE

1. PRECAUTIONS

NOTICE:

After turning the ignition switch OFF, a waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, be sure to read the precautions for disconnecting the cable from the negative (-) battery terminal before performing the work.

Click here

2. DISCONNECT THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

Click here

NOTICE:

When the cable has been disconnected, some systems must be reset after the cable is reconnected.

Click here

3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL CLIP

Click here

4. REMOVE MULTIPLEX NETWORK MAIN SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Click here

5. REMOVE POWER WINDOW SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Click here

6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here

7. REMOVE FRONT DOOR FRAME LOWER GARNISH

Click here

8. DETACH FRONT DOOR WEATHERSTRIP

Click here

9. REMOVE FRONT DOOR BELT MOULDING SEAL

Click here

10. REMOVE FRONT DOOR WINDOW INNER WEATHERSTRIP

Click here

11. REMOVE FRONT DOOR VENTILATION SEAL

Click here

12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY

Click here

13. REMOVE FRONT DOOR ACCESS HOLE COVER

Click here

14. REMOVE FRONT DOOR WINDOW SUB-ASSEMBLY

Click here

15. REMOVE DOOR FRAME UPPER GARNISH

Click here

16. REMOVE FRONT DOOR WINDOW REGULATOR SASH

Click here

17. REMOVE FRONT DOOR FRONT FRAME LOWER SUB-ASSEMBLY

Click here

18. REMOVE FRONT DOOR FIXED WINDOW GLASS

Click here

19. REMOVE FRONT DOOR GARNISH MOLDING NO. 4

HINT:

When removing the front door garnish molding No. 4, heat the vehicle body and the front door garnish molding No. 4 using a heat light.

Heating Temperature

Item

Temperature

Front Door Garnish Molding No. 4 and Vehicle Body

40 à 60 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body.

(a) Using a heat light, heat the front door garnish molding No. 4 and the vehicle body.

(b) Pull one end of the No. 4 front door garnish molding rearward to remove it.

HINT:

When pulling the No. 4 front door garnish molding, pull it parallel to the vehicle body.

20. REMOVE FRONT DOOR OUTER GARNISH MOLDING

HINT:

When removing the front door outer garnish molding, heat the vehicle body and the front door outer garnish molding using a heat lamp.

Heating Temperature

Item

Temperature

Front Door Outer Garnish Molding and Vehicle Body

40 à 60 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body.

(a) Using a heat lamp, heat the front door outer garnish molding and the vehicle body.

(b) Pull one end of the front door outer garnish molding rearward to remove it.

HINT:

When pulling the front door outer garnish molding, pull it parallel to the vehicle body.

21. REMOVE NO. 2 FRONT DOOR GARNISH MOLDING

HINT:

When removing the No. 2 front door garnish molding, heat the vehicle body and the No. 2 front door garnish molding using a heat lamp.

Heating Temperature

Item

Temperature

No. 2 Front Door Garnish Molding and Vehicle Body

40 à 60 °C

CAUTION:

  • Do not touch heated parts or the heat lamp. Touching them may cause burns.
  • Prolonged contact with heated parts may cause burns.

*a

Hot Surface

*b

Heat Lamp

NOTICE:

Do not overheat the vehicle body.

(a) Using a heat lamp, heat the No. 2 front door garnish molding and the vehicle body.

(b) Pull one end of the No. 2 front door garnish molding rearward to remove it.

HINT:

When pulling the No. 2 front door garnish molding, pull it parallel to the vehicle body.