Removal
REMOVAL
PRECAUTION / NOTICE / HINT
The procedures required (adjustment, calibration, initialization or registration) that must be performed once the parts have been removed, installed or replaced during windshield glass removal/installation are listed below.
Procedures Required After Replacement / Removal / Installation of PartsReplaced Part or Performed Procedure | Required Procedure | Effects / Inoperative Function When Necessary Procedure Not Performed | Link |
|---|---|---|---|
Windshield Glass |
Adjust Forward Recognition Camera |
|
NOTICE:
When replacing the windshield glass on a vehicle equipped with a forward recognition camera, be sure to use a genuine Toyota part. If a non-genuine Toyota part is used, the forward recognition camera may not be installable due to a missing bracket. In addition, the Dynamic Radar Cruise Control system, Lane Departure Warning system, Pre-Collision System, Forward Recognition Camera system or Automatic High Beam system may not operate properly due to a difference in transmission or black ceramic border.
PROCEDURE
1. REMOVE FRONT WINDSHIELD LH OUTER MOULDING
Click here![]()
2. REMOVE FRONT WINDSHIELD RH OUTER MOULDING
HINT:
Perform the same procedure as for the left side.
3. REMOVE FRONT WIPER ARM CAP
Click here![]()
4. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
Click here![]()
5. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
Click here![]()
6. REMOVE COWL TOP VENTILATOR GRILLE SUB-ASSEMBLY
Click here![]()
7. REMOVE INSIDE REAR VIEW MIRROR ASSEMBLY
Click here![]()
8. REMOVE RAIN SENSOR (with rain sensor)
Click here![]()
9. REMOVE FORWARD RECOGNITION CAMERA (with Toyota Safety Sense P system)
Click here![]()
10. REMOVE READING LIGHT ASSEMBLY
Click here![]()
11. REMOVE COURTESY LIGHT ASSEMBLY
Click here![]()
12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
![]()
13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Perform the same procedure as for the left side.
14. REMOVE FRONT PILLAR GARNISH LH
Click here
![]()
15. REMOVE FRONT PILLAR GARNISH RH
HINT:
Perform the same procedure as for the left side.
16. REMOVE ASSIST GRIP COVER
Click here![]()
17. REMOVE ASSIST GRIP SUB-ASSEMBLY
Click here![]()
18. REMOVE SUN VISOR BRACKET COVER
Click here![]()
19. REMOVE SUN VISOR ASSEMBLY LH (with courtesy light)
Click here![]()
20. REMOVE SUN VISOR ASSEMBLY RH (with courtesy light)
HINT:
Perform the same procedure as for the left side.
21. REMOVE SUN VISOR ASSEMBLY LH (without courtesy light)
Click here![]()
22. REMOVE SUN VISOR ASSEMBLY RH (without courtesy light)
HINT:
Perform the same procedure as for the left side.
23. REMOVE SUN VISOR BRACKET
Click here![]()
24. DETACH HEADLINING
(a) Lower the front part of the headlining slightly so that the windshield glass can be removed.
NOTICE:
Be careful not to damage the headlining or the interior of the vehicle.
HINT:
It is not necessary to completely remove the headlining.
25. REMOVE WINDSHIELD GLASS
(a) with windshield defroster system:
(1) Disconnect the windshield defroster connector.
(b) Apply protective tape to the body area around the windshield glass installation position to prevent scratching.
![]() |
Protective tape |
(c) Using a knife, cut the windshield outer moulding as shown in the illustration. |
|
(d) Make alignment marks on the windshield glass and the vehicle body at the locations shown in the illustration. HINT: Alignment marks are not necessary if the windshield glass is not to be reused. |
|
(e) From inside the vehicle, insert a piano wire between the vehicle body and the windshield glass. |
|
(f) Attach both ends of the wire to wooden blocks or similar objects that can be used as handles.
(g) Cut the adhesive by moving the piano wire around the perimeter of the windshield glass.
NOTICE:
- When removing the windshield glass, be careful not to damage the paint or the interior and exterior trim.
- To prevent scratching the instrument panel safety pad assembly when removing the windshield glass, place a plastic sheet between the piano wire and the instrument panel safety pad assembly.
- Be careful not to damage the front window center inside moulding.
(h) Release the windshield glass stoppers.
*A |
1 piece(s) |
*B |
2 piece(s) |
*1 |
Windshield Glass Stopper No. 1 |
*2 |
Windshield Glass Stopper No. 2 |
NOTICE:
- The windshield glass stopper No. 1 and windshield glass stopper No. 2 are attached to the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting the tape.
- To prevent the windshield glass from falling during this procedure, hold it in place using suction cups.
HINT:
Depending on the vehicle, either 1-piece or 2-piece type stoppers may be used.
(i) Using suction cups, remove the windshield glass.
NOTICE:
- Be careful not to drop the windshield glass.
- Leave as much tape as possible on the vehicle body when removing the windshield glass.
26. REMOVE WINDSHIELD GLASS ADHESIVE
(a) If reusing the windshield glass:
(1) Using a scraper, remove the windshield glass adhesive. NOTICE:
|
|
27. REMOVE WINDSHIELD OUTER MOULDING
(a) If reusing the windshield glass:
(1) Using a scraper, remove the windshield outer moulding. NOTICE:
|
|
28. REMOVE WINDSHIELD GLASS STOPPER NO. 1 (1 piece(s) stopper)
(a) If reusing the windshield glass:
(1) Using a scraper, remove the 2 windshield glass stoppers No. 1. NOTICE:
|
|
29. REMOVE WINDSHIELD GLASS STOPPER NO. 2 (2 piece(s) stopper)
(a) If reusing the windshield glass:
(1) Using a scraper, remove the 2 windshield glass stoppers No. 2. NOTICE:
|
|
30. REMOVE WINDSHIELD GLASS STOPPER NO. 1 (2 piece(s) stopper)
(a) Remove the 2 windshield glass stoppers No. 1 from the vehicle body. NOTICE: Be sure to replace the No. 1 windshield glass stoppers with new ones. |
![]() |
31. REMOVE FRONT WINDSHIELD INNER CENTER MOULDING
HINT:
Perform the following procedure only when replacement of the front windshield inner center moulding is necessary.
(a) Make alignment marks on the windshield glass at the locations shown in the illustration. |
|
(b) Using a scraper, remove the front windshield inner center moulding.
NOTICE:
- Be careful not to damage the windshield glass.
- Be sure to replace the front windshield inner center moulding with a new one.
.gif)
.png)








