Windows

Installation

~12min read

INSTALLATION

PRECAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass on a vehicle equipped with a forward recognition camera, be sure to use a genuine Toyota part. If a non-genuine Toyota part is used, the forward recognition camera may not be installable due to a missing bracket. In addition, the Dynamic Radar Cruise Control system, Lane Departure Warning system, Pre-Collision System, Forward Recognition Camera system or Automatic High Beam system may not operate properly due to a difference in transmission or black ceramic border.

PROCEDURE

1. CLEAN WINDSHIELD GLASS

(a) If reusing the windshield glass:

(1) Using a scraper, remove any remaining adhesive weatherstrip residue and adhesive from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.

(2) Clean the outer edges of the windshield glass using a residue-free solvent.

NOTICE:

  • Do not touch the windshield glass after cleaning it.
  • Even if the windshield glass is new, clean it with a residue-free solvent.

2. INSTALL WINDSHIELD GLASS STOPPER NO. 1 (2-piece stopper)

(a) Install the 2 new windshield glass stoppers No. 1 to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are supplied as replacement parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

3. INSTALL WINDSHIELD GLASS STOPPER NO. 2 (2-piece stopper)

(a) Using a brush or sponge, apply a coat of G primer to the installation area of the 2 new windshield glass stoppers No. 2.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Install the 2 new windshield glass stoppers No. 2 to the windshield glass as shown in the illustration.

Standard dimension:

Area

Measurement

a

13.7 to 14.7 mm (0.539 to 0.579 in.)

HINT:

Only 2-piece type windshield glass stoppers are supplied as replacement parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.

*a

Windshield Glass Rear Side

*b

Ceramic notch

*c

Side edge of windshield glass

4. INSTALL WINDSHIELD OUTER MOULDING

(a) Using a brush or sponge, apply a coat of G primer to the installation area of the new windshield outer moulding.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(b) Install the new windshield outer moulding to the windshield glass as shown in the illustration.

Standard dimension:

Area

Measurement

a

6.5 mm (0.256 in.)

b

2.5 to 7.5 mm (0.098 to 0.295 in.)

*a

Windshield Glass Rear Side

*b

Curved Surface Edge

5. INSTALL GLASS ADHESIVE WEATHERSTRIP

(a) Cut a new glass adhesive weatherstrip to the appropriate length as shown in the illustration.

Standard dimension:

Area

Measurement

a

297.9 cm (9.77 ft)

*a

Cut

(b) Using a brush or sponge, apply a coat of G primer to the installation area of the new glass adhesive weatherstrip.

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(c) Install the glass adhesive weatherstrip to the windshield glass as shown in the illustration.

*a

Windshield Glass Rear Side

*b

Ceramic notch

*c

Center position of glass adhesive weatherstrip

-

-

G primer

-

-

6. INSTALL FRONT WINDSHIELD INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of the front windshield inner center moulding is necessary.

(a) Using a brush or sponge, apply a coat of G primer to the installation area of the new front windshield inner center moulding.

Standard dimension:

Area

Measurement

a

14.5 mm (0.571 in.)

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

*a

Windshield Glass Rear Side

G primer

(b) Install the new front windshield inner center moulding to the windshield glass as shown in the illustration.

Standard dimension:

Area

Measurement

a

0.5 mm (0.020 in.) max.

NOTICE:

Be careful not to damage the front window center inside moulding.

*a

Windshield Glass Rear Side

*b

Alignment Mark

(c) Remove the alignment marks.

7. INSTALL WINDSHIELD GLASS

(a) Clean and correct the contact surface of the vehicle body.

(1) On the contact surface of the vehicle body, use a knife to remove excess adhesive as shown in the illustration.

NOTICE:

Leave as much adhesive as possible on the vehicle body.

(2) Clean the contact surface of the vehicle body with a piece of cloth soaked in residue-free solvent.

(b) Position the windshield glass.

(1) Using suction cups, correctly position the windshield glass.

(2) Check that the entire contact surface of the glass edge is flush.

(3) Align the alignment marks on the windshield glass and the vehicle body.

NOTICE:

Make sure the windshield glass stoppers are properly engaged with the vehicle body.

(4) Remove the windshield glass.

*a

Alignment Mark

(c) Using a brush, apply M primer to the mounting surface of the vehicle body.

NOTICE:

  • Do not apply M primer to the adhesive.
  • Do not apply too much M primer.
  • Allow the M primer coat to dry for at least 3 minutes.
  • Discard unused M primer.

HINT:

If any area other than the specified area is accidentally coated, wipe off the M primer before it dries using a clean piece of cloth.

(d) Using a brush or sponge, apply a coat of G primer to the adhesive tape application area.

*a

Windshield Glass Rear Side

*b

Adhesive Application Area

*c

Ceramic notch

-

-

G primer

-

-

Standard dimension:

Area

Measurement

a

7.0 mm (0.276 in.)

b

10.0 mm (0.394 in.) minimum

c

11.0 mm (0.433 in.) minimum

d

19.0 mm (0.748 in.) minimum

NOTICE:

  • Do not apply too much G primer.
  • Allow the G primer coat to dry for at least 3 minutes.
  • Discard unused G primer.

HINT:

  • Apply G primer to the ceramic frit.
  • If any area other than the specified area is accidentally coated, wipe off the G primer before it dries using a clean piece of cloth.

(e) Apply adhesive to the windshield glass.

Adhesive:

Genuine Toyota windshield adhesive (high modulus type) or equivalent

(1) Cut the end of the cartridge nozzle as shown in the illustration.

Standard dimension:

Area

Measurement

a

12.0 to 15.0 mm (0.472 to 0.591 in.)

b

8.0 to 11.0 mm (0.315 to 0.433 in.)

*a

Cartridge Nozzle

(2) Load the cartridge into the sealer gun.

(3) Apply adhesive to the windshield glass as shown in the illustration.

*a

Windshield Glass Rear Side

*b

Adhesive Center Position

*c

Center position of glass adhesive weatherstrip

*d

Ceramic notch

Adhesive

-

-

Standard dimension:

Area

Measurement

a

9.5 mm (0.374 in.)

b

3.0 mm (0.118 in)

c

6.6 mm (0.260 in.)

d

8.0 mm (0.315 in.)

HINT:

Apply adhesive to the ceramic frit.

(f) Install the windshield glass.

(1) Using suction cups, position the windshield glass so that the alignment marks line up, then press it gently along the edge.

NOTICE:

  • Make sure the windshield glass stoppers are properly engaged with the vehicle body.
  • Check the clearance between the vehicle body and the windshield glass.

(2) Press lightly on the outer surface of the glass to seat it properly on the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf.) minimum.

(3) Using a scraper, remove any adhesive beads or excess adhesive.

(4) Hold the windshield glass in place with protective tape until the applied adhesive hardens.

HINT:

Follow the adhesive manufacturer's instructions or the product instructions for the minimum waiting time before the vehicle can be driven.

*a

Alignment Mark

(g) When replacing the windshield glass or the front window center inside moulding:

(1) Remove the 2 protective retainers from the front window center inside moulding.

NOTICE:

Be careful not to damage the front window center inside moulding.

HINT:

Be sure to remove the protective retainers.

(h) With windshield defroster system:

(1) Connect the windshield defroster connector.

8. CHECK FOR WATER LEAKS

(a) Once the adhesive has hardened, apply water from the outside of the vehicle. Check for water leaks inside the cabin.

(b) If water leaks into the cabin, let the water dry and apply additional adhesive.

(c) Remove the masking tape.

9. INSTALL HEADLINING

(a) Return the front section of the headlining to its original position.

10. INSTALL SUN VISOR BRACKET

Click here

11. INSTALL LH SUN VISOR ASSEMBLY (with vanity light)

Click here

12. INSTALL RH SUN VISOR ASSEMBLY (with vanity light)

HINT:

Perform the same procedure as for the left side.

13. INSTALL LH SUN VISOR ASSEMBLY (without vanity light)

Click here

14. INSTALL RH SUN VISOR ASSEMBLY (without vanity light)

HINT:

Perform the same procedure as for the left side.

15. INSTALL SUN VISOR BRACKET COVER

Click here

16. INSTALL GRAB HANDLE COVER

Click here

17. INSTALL GRAB HANDLE SUB-ASSEMBLY

Click here

18. INSTALL LH FRONT PILLAR GARNISH

Click here

19. INSTALL RH FRONT PILLAR GARNISH

HINT:

Perform the same procedure as for the left side.

20. CONNECT LH FRONT DOOR OPENING TRIM WEATHERSTRIP

Click here

21. CONNECT RH FRONT DOOR OPENING TRIM WEATHERSTRIP

HINT:

Perform the same procedure as for the left side.

22. INSTALL COURTESY LIGHT ASSEMBLY

Click here

23. INSTALL READING LIGHT ASSEMBLY

Click here

24. INSTALL FORWARD RECOGNITION CAMERA (with Toyota Safety Sense P)

Click here

25. INSTALL RAIN SENSOR (with rain sensor)

Click here

26. INSTALL INSIDE REAR VIEW MIRROR ASSEMBLY

Click here

27. INSTALL UPPER HEADER VENTILATOR GRILLE SUB-ASSEMBLY

Click here

28. INSTALL LH FRONT WIPER ARM AND BLADE ASSEMBLY

Click here

29. INSTALL RH FRONT WIPER ARM AND BLADE ASSEMBLY

Click here

30. INSTALL FRONT WIPER ARM CAP

Click here

31. INSTALL LH WINDSHIELD OUTER MOULDING

Click here

32. INSTALL RH WINDSHIELD OUTER MOULDING

HINT:

Perform the same procedure as for the left side.