Seat Belt

Disposal

~13min read
4special tools
0102030405012.59N·mlb·ft
Tightening torque found on this page

DISPOSAL

PRECAUTION / NOTICE / HINT

CAUTION:

Before disposing of any SRS component, read and carefully follow all environmental and hazardous material regulations. Deployment before disposal may be considered a hazardous material treatment.

PROCEDURE

1. PRECAUTIONS

CAUTION:

  • Wear gloves and protective glasses when handling a rear outer seat belt assembly (3-point type) whose pretensioner has deployed.
  • Always wash your hands with water after completing the work.
  • Do not apply water, etc. to a rear outer seat belt assembly (3-point type) with a deployed pretensioner.
  • Always use the specified service tool to deploy the seat belt pretensioner (SRS airbag activation tool). Perform this operation in a location free from electrical noise.
  • Never dispose of a rear outer seat belt assembly (3-point type) whose pretensioner has not deployed.
  • The rear outer seat belt assembly (3-point type) produces an explosion noise when the pretensioner deploys. Therefore, perform this operation outdoors, in a place where it will not disturb nearby residents.
  • When deploying the seat belt pretensioner, perform the operation at least 10 m (32.8 ft) away from the vehicle.

HINT:

Before scrapping a vehicle equipped with a seat belt pretensioner, or disposing of a rear outer seat belt assembly (3-point type) with a seat belt pretensioner, always deploy the seat belt pretensioner beforehand following the procedure described below. If any abnormality occurs when deploying the seat belt pretensioner, contact the distributor's SERVICE AND REPAIR DEPARTMENT immediately.

2. DISPOSAL OF REAR OUTER SEAT BELT ASSEMBLY (3-POINT TYPE) (INSTALLED IN VEHICLE)

NOTICE:

  • When disposing of a rear outer seat belt assembly (3-point type) with a pretensioner, never deploy the pretensioner inside the customer's vehicle.
  • Be sure to follow the procedure below when deploying a seat belt pretensioner.

HINT:

Prepare a battery to be used as the power supply for deploying the seat belt pretensioner.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Refer to the Precautions.

Click here

(c) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Remove the roof side interior garnish assembly.

Click here

(e) Disconnect the seat belt pretensioner connector (for LH side).

(1) Remove the 3 bolts.

(2) Release the guides to detach the LH rear seat outer seat belt assembly (3-point type) with bracket.

(3) Release the clip.

*a

Lock button

*b

Protective tape

(4) Using a screwdriver whose tip has been wrapped with protective tape, pull out the lock button to release the lock, then disconnect the pretensioner connector as shown in the illustration.

(f) Disconnect the seat belt pretensioner connector (for RH side).

(1) Release the clip.

*a

Lock button

*b

Protective tape

(2) Using a screwdriver with the tip wrapped in protective tape beforehand, pull out the lock button to release the lock and disconnect the pretensioner connector as shown in the illustration.

(g) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Move the SST at least 10 m (32.8 ft) away from the front of the vehicle.

*a

Battery

*b

10 m (32.8 ft) minimum

CAUTION:

  • Do not perform deployment with any door or window open.
  • If deployment is performed with any window or door open, dust or gas may come into contact with the eyes or be inhaled.

(3) Close all doors and windows of the vehicle.

NOTICE:

Be careful not to damage the SST wire harness.

(h) Install the rear seat outer belt assembly LH (3-point type) (for left side).

(1) Engage the guides to temporarily install the rear seat outer belt assembly LH (3-point type) with bracket.

Bolt (A)

Bolt (B)

(2) Temporarily install the 3 bolts.

(3) Tighten the 3 bolts in the order shown in the illustration.

Torque:

Bolt (A):

12.5 N·m {127 kgf·cm, 9 ft·lbf}

Bolt (B):

42 N·m {428 kgf·cm, 31 ft·lbf}

(i) Deploy the seat belt pretensioner.

(1) Make sure that no one is in the vehicle or within a 10 m (32.8 ft) radius of the vehicle.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner deploys when the SST LED lights up.

CAUTION:

  • The rear outer seat belt assembly (3-point type) produces an explosion noise when the pretensioner deploys. Therefore, perform this operation outdoors, in a place where it will not disturb nearby residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(j) Dispose of the rear seat outer belt assembly (3-point type).

(1) Remove the rear outer seat belt assembly (3-point type) and the special service tool.

(2) Place the rear outer seat belt assembly (3-point type) in a plastic bag, seal the bag securely, and dispose of it in accordance with applicable regulations.

CAUTION:

  • The rear outer seat belt assembly (3-point type) becomes very hot when the pretensioner deploys. Wait at least 30 minutes after deployment before touching it.
  • Do not apply water, etc. to a rear outer seat belt assembly (3-point type) with a deployed pretensioner.
  • If water is applied to the rear outer seat belt assembly (3-point type) immediately after deployment, the steam may cause burns.
  • Always wear gloves and protective goggles when handling a rear outer seat belt assembly (3-point type) whose pretensioner has deployed.
  • If a rear outer seat belt assembly (3-point type) whose pretensioner has deployed is touched without wearing gloves and protective goggles, hot parts may cause burns and dust may enter the eyes.
  • After removal, quickly place the rear outer seat belt assembly (3-point type) in a plastic bag and seal it airtight.
  • Never dispose of a rear outer seat belt assembly (3-point type) whose pretensioner has not deployed.
  • If a rear outer seat belt assembly (3-point type) whose pretensioner has not deployed is disposed of and then deploys accidentally, unexpected injuries may occur.
  • Always wash your hands with water after completing the work.

HINT:

When scrapping a vehicle, deploy the seat belt pretensioners, then scrap the vehicle with the front outer seat belt assemblies installed.

3. DISPOSAL OF REAR OUTER SEAT BELT ASSEMBLY (3-POINT TYPE) (when not installed in vehicle)

NOTICE:

  • When disposing of a rear outer seat belt assembly (3-point type) with a pretensioner, never deploy the pretensioner inside the customer's vehicle.
  • Be sure to follow the procedure below when deploying a seat belt pretensioner.

HINT:

Prepare a battery to be used as the power supply for deploying the seat belt pretensioner.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Refer to the Precautions.

Click here

(c) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Remove the rear seat outer belt assembly (3-point type).

Click here

(e) Wind the seat belt webbing onto the retractor.

*a

Cut

*b

100 mm (3.94 in)

(f) When the seat belt webbing is sufficiently wound, cut it at approximately 100 mm (3.94 in.) from the retractor, as shown in the illustration.

HINT:

The retractor resistance increases in proportion to the length of seat belt webbing wound.

(g) Connect the SST.

(1) After connecting the following SSTs to each other, connect them to the seat belt pretensioner.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the pretensioner connector.

(2) Place the rear outer seat belt assembly (3-point type) on the floor and cover it with an unused wheel and tire assembly.

NOTICE:

  • Place the rear outer seat belt assembly (3-point type) as shown in the illustration.
  • The wheel and tire assembly may be damaged by the deployment of the seat belt pretensioner. Therefore, be sure to use an unused wheel and tire assembly.

(3) Place the SST and keep it at least 10 m (32.8 ft) away from the wheel and tire assembly.

NOTICE:

Be careful not to damage the SST wire harness.

(h) Deploy the seat belt pretensioner.

*a

Battery

*b

10 m (32.8 ft) minimum

(1) Make sure that no one is within a 10 m (32.8 ft) radius of the wheel and tire assembly.

(2) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(3) Press the SST activation switch to deploy the seat belt pretensioner.

HINT:

The seat belt pretensioner deploys when the SST LED lights up.

CAUTION:

  • The rear outer seat belt assembly (3-point type) produces an explosion noise when the pretensioner deploys. Therefore, perform this operation outdoors, in a place where it will not disturb nearby residents.
  • If this procedure is performed indoors or on a poor road where safety cannot be ensured, there is a risk of injury. Also, if this procedure is performed near a residential area, the deployment noise may disturb residents.

(i) Dispose of the rear seat outer belt assembly (3-point type).

(1) Remove the wheel and tire assembly and the SST.

(2) Place the rear outer seat belt assembly (3-point type) in a plastic bag, seal the bag securely, and dispose of it in accordance with applicable regulations.

CAUTION:

  • The rear outer seat belt assembly (3-point type) becomes very hot when the pretensioner deploys. Wait at least 30 minutes after deployment before touching it.
  • Do not apply water, etc. to a rear outer seat belt assembly (3-point type) with a deployed pretensioner.
  • If water is applied to the rear outer seat belt assembly (3-point type) immediately after deployment, the steam may cause burns.
  • Always wear gloves and protective goggles when handling a rear outer seat belt assembly (3-point type) whose pretensioner has deployed.
  • If a rear outer seat belt assembly (3-point type) whose pretensioner has deployed is touched without wearing gloves and protective goggles, hot parts may cause burns and dust may enter the eyes.
  • After removal, quickly place the rear outer seat belt assembly (3-point type) in a plastic bag and seal it airtight.
  • Never dispose of a rear outer seat belt assembly (3-point type) whose pretensioner has not deployed.
  • If a rear outer seat belt assembly (3-point type) whose pretensioner has not deployed is disposed of and then deploys accidentally, unexpected injuries may occur.
  • Always wash your hands with water after completing the work.