Supplemental Restraint Systems

Disposal

~9min read
2special tools

DISPOSAL

PRECAUTION / NOTICE / HINT

CAUTION:

Before disposing of any SRS component, read and carefully follow all environmental and hazardous material regulations. Deployment before disposal may be considered a hazardous material treatment.

PROCEDURE

1. PRECAUTIONS

CAUTION:

  • An airbag or pretensioner may be deployed accidentally by static electricity. To prevent this, be sure to touch a metal surface with bare hands to discharge static electricity before performing this operation.
  • Never dispose of an undeployed front seat airbag assembly.
  • The airbag makes an explosive noise when it deploys. Therefore, perform this operation outside, in a place where it will not disturb neighbors.
  • When deploying the airbag, always use the specified SST (SRS airbag deployment tool). Perform this operation in a place free from electrical noise.
  • Always stand at least 10 m (32.8 ft) away from the front seat airbag assembly when deploying it.
  • The front seat airbag assembly becomes hot after deployment. Therefore, do not touch it for at least 30 minutes.
  • Wear gloves and protective goggles when handling a front seat airbag assembly that has deployed.
  • Do not pour water or other liquids on a front seat airbag assembly that has deployed.
  • Always wash your hands with water after completing the work.

HINT:

Before scrapping a vehicle equipped with the SRS system or disposing of a front seat airbag assembly, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs during airbag deployment, immediately contact the service and repair department of TOYOTA MOTOR SALES, U.S.A, INC.

2. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (when installed in the vehicle)

NOTICE:

  • When disposing of the front seat airbag assembly, never use the customer's vehicle to deploy the airbag.
  • Be sure to perform the following procedure when deploying the airbag.

HINT:

Prepare a battery to be used as the power source for airbag deployment.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Refer to the Precautions.

Click here

(c) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Disconnect the front seat airbag assembly connector under the front seat assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push the white housing lock and slide the yellow CPA. (At this stage, the connector cannot be disconnected.)

*a

White housing lock

*b

Yellow CPA

Slide

(2) Push the white housing lock again and disconnect the connector.

NOTICE:

Do not press the part (A) shown in the illustration when disconnecting the connector.

(e) Install the SST.

CAUTION:

Make sure nothing is loose in the front seat assembly.

(1) After connecting the following SSTs to each other, connect them to the front seat airbag assembly.

SST: 09082-00700

SST: 09082-00820

NOTICE:

To prevent damage to the SST connector or wire harness, do not engage the secondary lock of the double lock.

(2) Move the SST at least 10 m (32.8 ft) away from the front side window of the vehicle.

*a

Battery

*b

10 m (32.8 ft) minimum

(3) Close all vehicle doors and windows, leaving just enough space to pass the SST wire harness through the front side window.

NOTICE:

Be careful not to damage the SST wire harness.

(4) Connect the SST red clip to the battery positive (+) terminal and the SST black clip to the battery negative (-) terminal.

(f) Deploy the airbag.

(1) Make sure that no one is in the vehicle or within a 10 m (32.8 ft) radius of the vehicle.

(2) Press the SST activation switch to deploy the airbag.

CAUTION:

  • Before deploying, make sure no one is inside or near the vehicle.
  • The front seat airbag assembly becomes hot after deployment. Therefore, do not touch it for at least 30 minutes.
  • Wear gloves and protective goggles when handling a front seat airbag assembly that has deployed.
  • Do not pour water or other liquids on a front seat airbag assembly that has deployed.
  • Always wash your hands with water after completing the work.

HINT:

The airbag deploys when the LED on the SST activation switch lights up.

3. DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (when not installed in the vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.

HINT:

Prepare a battery to be used as the power source for airbag deployment.

(a) Check that the SST operates correctly.

Click here

SST: 09082-00700

(b) Remove the front seat airbag assembly.

Click here

CAUTION:

  • Before removing the front airbag assembly, wait at least 90 seconds after turning the ignition switch to OFF and disconnecting the cable from the battery negative (-) terminal.
  • When storing the front seat airbag assembly, make sure the deployment side is facing up.

    Deployment side

(c) Using twisted wire, attach the front seat airbag assembly to an unused tire.

*a

Cable diameter

*b

Cross-sectional area of the grooved part of the cable

Cable:

Cross-section of the grooved part of the cable

1.25 mm2 (0.0019 in.2) minimum

CAUTION:

If the cable is too thin or if another object is used to attach the front seat airbag assembly, it may break when the airbag deploys. Always use an automotive cable with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).

HINT:

To calculate the cross-sectional area of the grooved part of the cable:

Cross-sectional area = 3.14 x (diameter)2 / 4

(1) Reinstall the 2 nuts on the front seat airbag assembly.

(2) Wrap at least 2 cables around the threaded studs of the front seat airbag assembly, as shown in the illustration.

(3) Place the front seat airbag assembly in the tire with the airbag deployment side facing inward.

*a

Width

*b

Inside diameter

Minimum tire dimensions:

Width

185 mm (7.28 in.)

Inside diameter

360 mm (1.18 ft)

CAUTION:

  • Make sure the cables are tightly secured. If the cables have slack, the front seat airbag assembly may break when the airbag deploys.
  • Always secure the front seat airbag assembly with the deployment side facing the inside of the tire, as shown in the illustration.

    Deployment side

NOTICE:

Airbag deployment may damage the tire. Use an unused tire.

(d) Install the SST.

(1) Connect the SST connector to the front seat airbag assembly connector.

SST: 09082-00820

(e) Position the tires.

(1) Place at least 2 tires below the tire to which the front seat airbag assembly is attached.

Minimum tire dimensions:

Width

185 mm (7.28 in.)

Inside diameter

360 mm (1.18 ft)

NOTICE:

Do not place the SST connector under the tire, as this could damage it.

*a

Tires (2 minimum)

*b

Inside diameter

*c

Width

(2) Place at least 2 tires above the tire to which the front seat airbag assembly is attached. The upper tire must be placed on a wheel.

NOTICE:

The wheel and tires may be damaged by airbag deployment. Make sure to use a wheel and tires that have not been used.

(3) Tie the tires together using 2 cables.

CAUTION:

Make sure the cables are tightly secured. If the cables are not tight, the tires will come apart when the airbag deploys.

(f) Install the SST.

(1) Connect the SST connector.

SST: 09082-00700

NOTICE:

To avoid damaging the SST connector or wire harness, do not engage the secondary lock of the double lock. Also, leave slack in the SST wire harness inside the tire.

*1

Front seat airbag assembly

*a

Battery

*b

10 m (32.8 ft) minimum

(2) Move the SST at least 10 m (32.8 ft) away from the airbag secured to the tire.

(g) Deploy the airbag.

(1) Connect the red SST clip to the battery positive (+) terminal and the black SST clip to the battery negative (-) terminal.

(2) Make sure no one is within 10 m (32.8 ft) of the tire to which the front seat airbag assembly is attached.

(3) Press the SST activation switch to deploy the airbag.

CAUTION:

Before deploying the airbag, make sure no one is near the airbag.

HINT:

The airbag deploys when the LED on the SST activation switch lights up.

(h) Dispose of the front seat airbag assembly.

CAUTION:

  • The front seat airbag assembly becomes hot after deployment. Therefore, do not touch it for at least 30 minutes.
  • Wear gloves and protective goggles when handling a front seat airbag assembly that has deployed.
  • Do not pour water or other liquids on a front seat airbag assembly that has deployed.
  • Always wash your hands with water after completing the work.

(1) Remove the front seat airbag assembly from the tire.

(2) Place the front seat airbag assembly in a plastic bag, seal it tightly, and dispose of it in accordance with local regulations.